WE-VIBE MOXIE (01) PDF Document

You can control your WE-VIBE MOXIE using its control button.

Turn On: Press the control button.

Change Vibration Mode: Press the control button again to cycle through the different modes.

Turn Off: Press and hold the control button down for 2 seconds.

The buttons also allow you to adjust the intensity.

Increase Intensity: Press the button for On/intensity up.

Decrease Intensity: Press the button for Off/intensity down.

To charge your WE-VIBE MOXIE, connect the included USB charging cable to the charging contacts on the device and a USB power source.

Charging Time: A full charge may take up to 2 hours, but typically takes 90 minutes. The time depends on the amount of charge remaining in the battery.

Indicator Light Status:

Fast Blinking Light: The device is charging.

Solid Light: The device is fully charged.

Light Off: There is no power, or the charging cable is not properly placed.

Additional Charging Information:

There is no need to drain the battery before recharging.

If you use a computer’s USB port, the WE-VIBE MOXIE will not charge if the computer goes into sleep mode. Any USB power adapter can be used for charging.

The WE-VIBE MOXIE will not charge if it is too hot (+45 degrees Celsius). Charging will begin automatically once the temperature reaches a safe level.

For best performance and long battery life, recharge the device before the vibrations weaken. If stored, the charge will gradually diminish over time.

The indicator light on your WE-VIBE MOXIE communicates its status. A slow blinking light indicates that the battery is low and needs to be recharged.

To clean your WE-VIBE MOXIE, wash it with a compatible toy cleaner or soap and water.

To ensure the longevity and safety of your WE-VIBE MOXIE, please adhere to the following guidelines:

Do not use with silicone lubricants as they will damage the product.

Do not clean with products that contain alcohol, petrol, or acetone.

Do not boil, bake, microwave, or put the device in a dishwasher.

Do not store in extreme temperatures.

Do not charge the device near water.

Place the WE-VIBE MOXIE inside your underwear. Use the magnetic clip on the outside of the underwear to hold the device in place. Once secured, it can be worn comfortably during a variety of activities.

It is recommended to apply a water-based lubricant to your WE-VIBE MOXIE before use. Do not use silicone-based lubricants as they can damage the product.

To pair your WE-VIBE MOXIE with your smartphone, download the We-Connect™ app and follow the on-screen instructions. The app allows you to switch between preset vibration modes and customize your own.

If you are unable to pair your WE-VIBE MOXIE with the smartphone app, it may already be paired to its wireless remote. You should first try unpairing it from the remote.

To unpair the remote, press and hold any button on the remote for 5 seconds. The LED light on the remote will flash and then turn off, indicating it has been unpaired. After unpairing the remote, attempt to pair the device with your smartphone again.

To Pair with the Remote:

Step 1. Prepare the WE-VIBE MOXIE for pairing by holding down its control button for 5 seconds until it pulses twice.

Step 2. To complete the pairing, hold either the left or right button on the remote down for 5 seconds.

To Unpair from the Remote:

To unpair the remote, hold the left or right button on the remote down for 5 seconds.

For long-distance play, both you and your partner need to download the We-Connect™ app on your smartphones. The WE-VIBE MOXIE should be paired to the phone that will remain within its Bluetooth range. Once paired, you can send your partner an invitation by selecting “connect lover” from the app menu. This allows for control over any distance.

The WE-VIBE MOXIE comes with several preset vibration modes:

Low

Medium

High

Ultra

Pulse

Wave

Tease

Ramp

Tempo

Massage

Additionally, you can create your own custom vibration patterns in the We-Connect™ app.

For the best connection results when playing in the same room, the WE-VIBE MOXIE connects from up to 30 feet of direct, line-of-sight distance and within approximately 20 feet of 360-degree range. These ranges are based on ideal conditions, with legs uncrossed and with little to no interference.

To preserve battery life, your WE-VIBE MOXIE is set to enter sleep mode after 30 minutes of inactivity. This includes periods with no changes to vibration patterns or intensity settings. You can update this setting to keep the device on standby for up to 4 hours before it enters sleep mode.

To update the sleep mode setting:

Step 1. Pair your WE-VIBE MOXIE using the We-Connect™ app.

Step 2. Go to Settings > Device Settings > We-Vibe Sleep Timeout.

Step 3. Update the time setting.

If your WE-VIBE MOXIE enters sleep mode, simply re-pair it with the app when you’re ready to play again.

The WE-VIBE MOXIE uses Bluetooth® bonding for advanced security, which prevents other signals from disrupting your wireless connection. It pairs with and trusts only two controllers (phones and/or remotes) at a time, though it only connects with one at a time. To change a trusted controller, you must reset the device.

To reset the WE-VIBE MOXIE:

Step 1. Press and hold the control button on the WE-VIBE MOXIE down for 10 seconds. If the device is on, the LED will flash at the 5-second mark and then flash quickly once you’ve reached 10 seconds.

Step 2. Remove the WE-VIBE MOXIE from the Bluetooth device list on your phone.

Step 3. Pair the WE-VIBE MOXIE with the new controller (phone or remote).