VOLLRATH MIRAGE FAJITA 59510F (01) PDF Document

The VOLLRATH MIRAGE FAJITA 59510F is intended to be used to re-thermalize pre-cooked fajitas in a cast-iron pan from a refrigerated state to a serving temperature of 160°F (71°C) or higher. It is designed for use in commercial food service operations only and is not intended for household, industrial, or laboratory use.

Before using your VOLLRATH MIRAGE FAJITA 59510F for the first time, please follow these setup steps:

1. Remove the unit from the carton and inspect it for any damage that may have occurred during shipping.

2. Remove all packing materials and tape, as well as any protective plastic, from the unit.

3. Place the unit on a flat, level surface.

4. Plug the unit into a grounded electrical outlet that matches the voltage on the rating plate. Do not use a power strip or extension cord with this unit.

5. The unit must be programmed before its first use.

To ensure safe operation of your VOLLRATH MIRAGE FAJITA 59510F, always follow these precautions:

WARNINGS:

Plug the unit only into grounded electrical outlets matching the nameplate-rated voltage.

Do not use an extension cord with this equipment.

Do not operate the unit unattended.

Do not operate any equipment with a damaged cord or plug.

Keep water and other liquids from entering the inside of the equipment. Liquid inside the unit could cause an electric shock.

Keep the equipment and power cord away from open flames, electric burners, or excessive heat.

Turn off, unplug, and allow the machine to cool before cleaning or performing maintenance.

NOTICES:

Use the VOLLRATH MIRAGE FAJITA 59510F only with induction-ready cookware. The included G1 pan must be used.

Do not place empty cookware on the operating unit as it could overheat and cause damage.

Do not place credit cards, magnetic media, or other magnetic-sensitive objects near the unit.

Do not obstruct the air intake or exhaust fan. Maintain a minimum of 4 inches (10 cm) of space around the unit for proper air circulation.

The unit should only be used on a flat, level surface.

This equipment is not designed or intended for use by children.

To ensure safe operation, it is important to understand the meaning of the safety statements for the VOLLRATH MIRAGE FAJITA 59510F:

Warning: This indicates the presence of a hazard that will or can cause severe personal injury or death.

Caution: This indicates the presence of a hazard that will or can cause minor or major personal injury if the caution is ignored.

Notice: This is used to note information that is important but not hazard-related.

The VOLLRATH MIRAGE FAJITA 59510F includes the following features and controls:

A. CONTROL PANEL: Contains all the buttons and display for operating the unit.

B. LED DISPLAY: Shows the current power level, temperature, or timer setting.

C. POWER LIGHT: Illuminates to indicate that the power is on.

D. TEMPERATURE LIGHT: Illuminates when temperature mode is active.

E. FAJITA LIGHT: Illuminates when the dedicated Fajita mode is active.

F. TIMER LIGHT: Illuminates when the timer mode is active.

G. INCREASE ARROW (∧): Increases the power level, temperature, or time.

H. DECREASE ARROW (∨): Decreases the power level, temperature, or time.

I. POWER / TEMP BUTTON: Toggles the unit between power and temperature control modes.

J. TIMER BUTTON: Activates the timer function.

K. ON / OFF BUTTON: Turns the unit on or off.

L. CERAMIC TOP: The cooking surface for the induction-ready pan.

M. AIR INTAKE FAN: Located on the bottom of the unit, it cools the internal components. It is important not to block this opening.

To turn on the VOLLRATH MIRAGE FAJITA 59510F, follow these steps:

Step 1. Place the unit on a flat, stable surface.

Step 2. Plug the power cord into a grounded electrical outlet with the correct voltage.

Step 3. Place an induction-ready pan containing food or liquid on the ceramic top. The unit will not operate without a pan in place.

Step 4. Press the ON / OFF button. The POWER light will illuminate, and the display will show the default Fajita mode settings.

The VOLLRATH MIRAGE FAJITA 59510F offers three cooking modes. Here is how to use them:

Fajita Mode (Default)

This is the default mode when the unit is turned on. The Fajita light will be illuminated. The unit heats for a specified time at a specified power level. When the cycle is complete, the unit will beep, and the display will show “End”. The unit then enters Standby mode, maintaining a set temperature for a set time.

Power Level Mode

1. Press the POWER / TEMP button until the POWER light is illuminated.

2. Use the INCREASE (∧) and DECREASE (∨) arrows to set the power level from 1 to 100.

Temperature Level Mode

1. Press the POWER / TEMP button until the TEMPERATURE light is illuminated.

2. Use the INCREASE (∧) and DECREASE (∨) arrows to set the desired temperature.

To set the timer on your VOLLRATH MIRAGE FAJITA 59510F, follow these steps:

Step 1. After setting the desired cooking mode (Power Level or Temperature Level), press the TIMER button. The TIMER light will illuminate, and the display will flash “0”.

Step 2. Use the INCREASE (∧) and DECREASE (∨) arrows to set the cooking time. The timer can be set in 30-second increments up to 180 minutes.

Step 3. After 3 seconds of inactivity, the timer will begin to count down, and the display will show the remaining time.

Step 4. When the timer reaches “0”, the unit will beep, the display will show “End”, and the unit will shut off.

To switch the temperature display between Fahrenheit (°F) and Celsius (°C) on the VOLLRATH MIRAGE FAJITA 59510F, press and hold the POWER / TEMP button for three seconds.

To prevent settings from being accidentally changed on the VOLLRATH MIRAGE FAJITA 59510F, you can lock the control panel.

To Lock: Press and hold the INCREASE (∧) and DECREASE (∨) arrows simultaneously for three seconds. The display will show “Loc” to indicate that the panel is locked.

To Unlock: Press and hold the INCREASE (∧) and DECREASE (∨) arrows simultaneously for three seconds again. The display will show the current power or temperature setting, indicating the panel is unlocked.

The VOLLRATH MIRAGE FAJITA 59510F must be programmed before first use. Follow these steps to set the parameters for Fajita Mode and Standby Mode:

Step 1. Turn the unit on by pressing the ON/OFF button.

Step 2. Press and hold the TIMER button for three seconds. “P1” will appear on the display, and the FAJITA light will illuminate.

Step 3. Press the TIMER button to cycle through the four programmable settings: P1, P2, P3, and P4.

P1 – Set Maximum Power Level for Fajita Mode (Default: 80)

When “P1” is displayed, use the INCREASE (∧) and DECREASE (∨) arrows to set a value from 1 to 100. Press TIMER to save the setting and move to P2.

P2 – Set Time for Fajita Mode (Default: 30 seconds)

When “P2” is displayed, use the arrows to set a time from 1 to 180 seconds. Press TIMER to save the setting and move to P3.

P3 – Set Standby Temperature (Default: 180°F / 82°C)

When “P3” is displayed, use the arrows to set a temperature from 86° to 400°F (30° to 204°C). Press TIMER to save the setting and move to P4.

P4 – Set Standby Time (Default: 10 minutes)

When “P4” is displayed, use the arrows to set a time from 1 to 180 minutes. Press TIMER to save the setting and exit programming mode.

The following table shows the range and default values for each setting:

To maintain the appearance and prolong the life of your VOLLRATH MIRAGE FAJITA 59510F, follow these daily cleaning instructions:

1. Turn off the unit and unplug the power cord.

2. Allow the unit to cool down completely before cleaning.

3. Wipe the exterior of the unit with a clean, damp cloth.

4. Do not use abrasive materials, scratching cleansers, or scouring pads to clean the unit, as this can damage the finish.

5. Do not immerse the cord, plug, or the unit itself in water or any other liquid.

The air filter on the VOLLRATH MIRAGE FAJITA 59510F should be cleaned daily. Follow these steps:

Step 1. Slide the air filter out from under the unit.

Step 2. Wash the filter in a sink with soap and water, or place it in a dishwasher.

Step 3. Ensure the filter is completely dry, then slide it back into place.

If your VOLLRATH MIRAGE FAJITA 59510F is not operating correctly, please refer to the following troubleshooting guide:

If an error code appears on the display of your VOLLRATH MIRAGE FAJITA 59510F, refer to the table below for its meaning and the corrective action required.

No, there are no user-serviceable parts within the VOLLRATH MIRAGE FAJITA 59510F. To avoid serious injury or damage, you should never attempt to repair the induction range or replace a damaged power cord yourself.