TOYOTA CAMRY 2025 (02) PDF MANUAL

The steering wheel controls allow you to operate various vehicle systems without taking your hands off the wheel.

Left Side Controls:

Multi-Information Display (MID) control switches: Navigate menus and make selections on the display in the instrument cluster.

Audio volume control switch: Increase or decrease the audio volume.

Voice command talk switch: Activate the voice recognition system.

Telephone switch: Answer or end phone calls.

Right Side Controls:

Lane Tracing Assist (LTA) switch: Toggles the LTA system on or off.

Full-Speed Range Dynamic Radar Cruise Control (DRCC) switches: Activate, set, resume, or cancel cruise control, and adjust the following distance.

Audio control switches: Change tracks or radio stations.

Paddle shifters (if equipped): Manually shift gears when in “S” mode.

The control panel to the left of the steering wheel includes the following buttons:

Automatic High Beams (AHB) switch: Turns the AHB system on or off.

VSC OFF switch: Turns off Vehicle Stability Control (VSC) and Traction Control (TRAC).

Instrument panel light control switch: Adjusts the brightness of the instrument panel lights.

Panoramic View Monitor (PVM) switch (if equipped): Activates the PVM display.

Trunk opener switch: Opens the trunk.

Fuel tank door release switch: Releases the fuel tank door.

Unlocking Doors:

While carrying the Smart Key, you can either press the unlock button on the remote or grasp the driver’s door handle. Pressing the unlock button once unlocks the driver’s door; pressing it twice unlocks all doors. This function can be programmed to unlock all doors on the first press. Grasping the front passenger door handle will unlock all doors.

Note: If a door is not opened within 60 seconds of unlocking, all doors will relock for safety.

Locking Doors:

While carrying the Smart Key, you can either press the lock button on the remote or touch the sensor on the exterior of the front door handles.

Unlocking/Opening the Trunk:

Press and hold the trunk button on the Smart Key remote.

Panic Button:

Press and hold the red panic button on the remote to sound an alarm and flash the vehicle’s lights. Press any button on the remote to turn it off.

To start the vehicle, the Smart Key must be inside the car.

1. Ensure the shift lever is in the Park (P) position.

2. Firmly depress the brake pedal.

3. Press the “POWER” button. The “READY” indicator will illuminate in the instrument cluster, indicating the vehicle is on and ready to be driven.

Without depressing the brake pedal, pressing the “POWER” button will cycle through the operation modes in the following succession:

Off: All systems are OFF. Emergency flashers can be used.

ACCESSORY: Some electrical components, such as the audio system, can be used.

ON: All electrical components can be used.

Fuel Tank Door:

1. Press the fuel tank door release switch located on the instrument panel to the left of the steering wheel.

2. Turn the fuel cap counter-clockwise to open.

3. When closing, tighten the cap until one click is heard. If the cap is not tightened enough, the Check Engine indicator may illuminate.

Hood:

1. Pull the hood lock release lever located under the instrument panel on the driver’s side.

2. Go to the front of the vehicle, pull the secondary latch lever to the left, and raise the hood.

3. Secure the hood by inserting the support rod into its designated slot.

The vehicle must be on and the brake pedal depressed to shift out of Park (P).

Shift Positions:

P: Park

R: Reverse

N: Neutral

D: Drive – For normal driving.

S: Sequential Mode – For manual-style shifting.

“S” (Sequential) Mode:

From the “D” position, move the shift lever to the “S” position. You can then manually change gears.

Using the Shift Lever: Push the lever forward (+) to upshift and pull it back (-) to downshift.

Using Paddle Shifters (if equipped): Pull the right paddle (+) to upshift and the left paddle (-) to downshift.

Downshifting can increase power for climbing hills or provide engine braking for descending hills. For the best fuel economy, always drive in the “D” position for normal driving conditions.

To maximize your vehicle’s fuel efficiency, follow these tips:

Ensure tire pressures are maintained at the levels specified in the “Owner’s Manual”.

When possible, link trips to reduce engine cold starts.

Avoid driving at speeds that are higher than necessary, especially on the highway.

When possible, avoid sudden stops to maximize regenerative braking energy.

Minimize use of the air conditioning.

When using a smartphone as a Digital Key, please be aware of the following:

The Digital Key requires communication between the smartphone and a server. It may become unusable if the smartphone is not connected to the Internet.

If the smartphone battery is depleted, it cannot be used as a Digital Key.

If the Smart Key system is deactivated in vehicle settings, the Digital Key will also be disabled.

Radio wave environment can affect the Digital Key’s usability.

Delete Digital Keys when transferring vehicle ownership.

If the vehicle is not operated for 14 days or more, the Digital Key may take some time to connect and operate after a door handle is touched.

If your smartphone is lost or stolen, contact your Toyota dealer immediately.

When taking your vehicle for inspection or repairs, bring the electronic key.

With the Digital Key alone, no vehicle lights will illuminate when you approach the vehicle.

Automatic door locks can be programmed to operate in different modes or turned OFF.

Default Setting: Shift position linked

Doors lock when shifting from Park (P).

Doors unlock when shifting into Park (P).

Customized Setting: Speed linked

Doors lock when the vehicle speed is approximately 12 mph (20 km/h) or higher.

Customized Setting: Driver’s door linked

Doors unlock when the driver’s door is opened.

Door Lock Switches:

Switches are located on both the driver’s and front passenger’s door panels. Press the switch to lock or unlock all doors simultaneously.

Power Windows:

The driver’s door has controls for all windows.

All window auto up/down: Press a window switch completely down or pull it completely up and release to fully open or close the window. To stop the window partway, operate the switch lightly in the opposite direction.

Window lock switch: Press this switch to deactivate all passenger window controls. The driver’s window remains operable.

To adjust the steering wheel’s position:

1. Locate the lock release lever below the steering column.

2. Push the lever down to unlock the steering column.

3. Hold the steering wheel and move it to the desired angle (tilt) and length (telescopic).

4. Return the lever to its original position to lock the steering wheel in place.

Note: Do not attempt to adjust the steering wheel while the vehicle is in motion.

Electric Parking Brake (EPB):

Manual Mode: While the vehicle is stopped and the brake pedal is depressed, pull the EPB switch up to set the parking brake. To release, depress the brake pedal and press the EPB switch down.

Automatic Mode: To turn ON, while stopped, pull and hold the EPB switch until a buzzer sounds. In this mode, shifting into Park (P) will automatically set the brake. Shifting out of P will automatically release it. To turn OFF, press and hold the EPB switch until a buzzer sounds.

Brake Hold System:

Press the “HOLD” button to activate the system. It keeps the brakes applied after you’ve come to a complete stop with the shift lever in D, S, or N, even if you release the brake pedal. The brake releases automatically when the accelerator pedal is depressed (in D or S) for a smooth start.

Use the MID control switches (arrow buttons and “OK” button) on the left side of the steering wheel to change and select information. Press the back-arrow button to return to the previous screen.

The MID can show the following information categories:

Driving information display: Shows trip data, fuel economy, etc.

Driving support system information display: Shows the status of systems like LTA and DRCC.

Audio system-linked display: Shows current audio source information.

Vehicle information display: Shows tire pressure and other vehicle data.

Settings display: Access and customize various vehicle settings.

Warning message display: Shows any active warnings or system alerts.

The Head-Up Display (HUD) projects driving information onto the windshield. To change the display type or settings, press the MID control switches, select the settings icon, and then select the HUD options.

The HUD can display information such as:

1. Content display area (Driving support system info, navigation, tachometer)

2. Speed limit/Road Sign Assist (RSA) display area

3. Shift position/shift range

4. Speedometer

5. Driving support system information display

Front Seat Adjustments (Power Seat):

Controls are located on the outboard side of the seat cushion.

Seat position: Use the horizontal control to move the seat forward and backward.

Seatback angle: Use the vertical control to recline or raise the seatback.

Vertical height & Seat cushion angle: Use the front or rear part of the cushion height control to raise or lower the whole seat or just the front edge.

Lumbar support (driver’s side only): Use the round control to increase or decrease lower back support.

Folding Rear Seats:

The release levers are located in the trunk. Pull the lever for the desired side to release the seatback, then fold it down from inside the cabin.

Head Restraints:

To raise, simply pull up. To lower, press the lock release button on the side of the head restraint post base and push down.

1. On the audio multimedia main menu, press the settings icon.

2. Select “General” on the submenu.

3. Select “Date & Time”.

4. Select the desired items to be set, such as time zone or 24-hour time.

Note: It is recommended to set the “Set date & time by GPS” feature to ON for automatic time updates based on your location.

The light controls are on a stalk on the left side of the steering column.

Headlights:

Rotate the end of the stalk to select a mode:

DRL OFF: Daytime Running Lights off.

AUTO: Headlights turn on/off automatically based on ambient light.

Parking lights: Turns on parking lights, taillights, and license plate lights.

Headlights: Turns on headlights and all lights above.

High Beams: Push the stalk forward to turn on the high beams. Pull it back to its original position to turn them off.

High Beam Flasher: Pull the stalk toward you to flash the high beams.

Automatic High Beams (AHB): With the headlight switch in AUTO, press the AHB button on the dashboard. The system will automatically switch between high and low beams as appropriate.

Turn Signals:

Push the stalk up for a right turn signal or down for a left turn signal. For a lane change, move the lever partway and release; the signals will flash three times.

The wiper controls are on a stalk on the right side of the steering column. Move the stalk to select a speed.

Intermittent Wipers (if equipped):

MIST: Single wipe.

OFF: Wipers off.

INT: Intermittent operation. Rotate the ring on the stalk to adjust the frequency of the wipe.

LO: Slow, continuous wipe.

HI: Fast, continuous wipe.

Rain-Sensing Wipers (if equipped):

OFF: Wipers off.

AUTO: Wipers operate automatically when rain is detected. Rotate the ring on the stalk to adjust sensor sensitivity.

LO: Slow, continuous wipe.

HI: Fast, continuous wipe.

Washers: Pull the stalk toward you to spray washer fluid and activate the wipers.

Electronic Sunshade:

Open: Slide and hold the rearward switch. It will open fully automatically. A quick slide and release will also open it fully.

Close: Slide and hold the forward switch. It will close fully automatically. A quick slide and release will also close it fully.

Panoramic Moonroof (Glass Panel):

Slide Open: Slide and hold the rearward switch. The moonroof and sunshade will open together automatically.

Slide Close: Slide and hold the forward switch. The moonroof will close fully automatically.

Tilt-Up: Press the center of the switch to tilt the moonroof up.

Tilt-Down: Press and hold the center of the switch to tilt the moonroof down from the tilt-up position.

You can stop the moonroof or sunshade partway by operating the switch again in either direction while it is in motion.

Sliding Operation:

Press the “OPEN” side of the switch once to open the moonroof partway. Press it again to open completely.

Press the “CLOSE” side of the switch to close it.

Tilting Operation:

Press the “UP” side of the switch to tilt the moonroof open.

Press the “DOWN” side of the switch to close it from the tilted position.

Lightly pressing either side of the switch while it’s in motion will stop it partway.

After pairing a Bluetooth-enabled phone, you can use the controls on the steering wheel.

Start and end call button: Press to answer an incoming call or end an active call.

Volume control: Adjust the call volume.

Voice command talk switch: Press to activate your phone’s voice assistant.

“MODE” button: Press to change the audio mode. Press and hold to mute or pause audio.

“< >” buttons: Use to search within a selected audio feature.

The vehicle must be in the “ACCESSORY” or “IGNITION ON” mode to use the wireless charger.

1. Place a compatible mobile device on the charging tray, centering it on the charging area for best results.

2. An amber indicator light will illuminate while charging is in progress.

3. When charging is complete, the indicator will illuminate green. Note that some phones or cases may not cause the green light to illuminate even when fully charged.

Automatic Mode:

Press the “AUTO” button. Set your desired temperature using the temperature control dials. The system will automatically adjust fan speed, airflow mode, and air intake to maintain that temperature.

Key Controls:

Temperature control dials: Adjust for the driver and passenger sides. Press the “SYNC” button to link both sides to the driver’s setting.

Fan speed control: Press the up/down arrows to manually adjust fan speed.

Airflow mode buttons: Manually select where the air flows (face, feet, windshield).

A/C button: Toggles the air conditioning compressor on and off.

Recirculate/Fresh air button: Toggles between recirculating inside air and drawing in fresh outside air.

Windshield defogger button: Directs airflow to the windshield to clear fog or frost.

Rear window defogger button: Activates the heating elements in the rear window and outside mirrors.

The vehicle must be on to use these features.

Heated/Ventilated Seats (if equipped):

The buttons are located on the center console. Press the button to cycle through the settings. For heated seats, there are multiple heat levels (e.g., high, medium, low) and an off setting. For ventilated seats, there are multiple fan speeds and an off setting.

Heated Steering Wheel (if equipped):

Press the button with the steering wheel icon on the center console to turn the feature on or off. An indicator light will show when it is active.

Driving Mode Select Switches:

Use the “ECO” and “SPORT” buttons on the center console to change the driving mode.

Normal mode: The default mode, suitable for normal driving.

ECO mode: Helps achieve lower fuel consumption by adjusting throttle response and climate control. The ECO indicator will appear on the dash.

SPORT mode: Provides a higher level of response for more spirited driving. The SPORT indicator will appear on the dash.

EV Drive Mode:

Press the “EV MODE” button on the center console. This mode uses only the electric motor for power, ideal for short-distance, low-speed driving to reduce noise and emissions. The EV mode indicator will appear on the dash. This mode has limitations based on battery charge, vehicle speed, and other factors.

The Vehicle Stability Control (VSC) and Traction Control (TRAC) systems help maintain control under adverse conditions.

To help free a stuck vehicle from mud or snow, you may need to turn these systems off.

To disable TRAC only: While the vehicle is stopped, press the “VSC OFF” switch. A “Traction Control Turned OFF” message will appear.

To disable both VSC and TRAC: While the vehicle is stopped, press and hold the “VSC OFF” switch for at least 3 seconds.

Blind Spot Monitor (BSM):

The system uses radar sensors to detect vehicles in the blind spots on either side of your vehicle. When a vehicle is detected, an indicator in the corresponding outside rear view mirror will illuminate. If you activate your turn signal while a vehicle is in your blind spot, the indicator will flash.

Rear Cross-Traffic Alert (RCTA):

When you are backing up (in Reverse), the system detects vehicles approaching from the right or left. If an approaching vehicle is detected, the outside rear view mirror indicators will flash, a buzzer will sound, and an icon will be displayed on the multimedia screen.

Turning the System On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select the BSM or RCTA icon.

3. Press “OK” to turn the system On or Off.

Safe Exit Alert (SEA) is a system that uses rear-side radar sensors to help warn occupants of an approaching vehicle or bicycle that may collide with an opened door. It functions before or as a door is being opened to reduce the possibility of a collision.

To turn the system On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select the “SEA” option.

3. Press “OK” to turn the system On or Off.

4. Press the back-arrow button to exit the menu.

This system uses sensors to detect objects around the vehicle during low-speed maneuvers like parking. If it determines a collision is possible, it provides warnings. If it determines a collision is extremely likely, it can automatically apply the brakes to help avoid or reduce the impact.

The system functions for:

Static objects: When traveling at low speed and the brake pedal is not depressed or is depressed late, or if the accelerator is pressed excessively, or if the wrong shift position is selected (e.g., Drive instead of Reverse).

Rear-crossing vehicles: When reversing and an approaching vehicle is detected, and the brake is not depressed or is depressed late.

Rear pedestrians: When reversing and a pedestrian is detected behind the vehicle, and the brake is not depressed or is depressed late.

To turn the system On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select the “PKSB” (Parking Support Brake) option and press “OK” to turn the system On or Off.

The parking assist sonar system uses sensors to measure the distance to nearby obstacles when parking or maneuvering at low speeds. It communicates this information via the Multimedia Display and a beeping sound.

As you get closer to an obstacle, the indicator on the display will change from solid (far) to blinking (near), and the beeping will switch from intermittent to continuous.

To turn the system On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select the Parking Assist icon (a “P” with radiating lines) and press “OK” to turn the system On or Off.

Traffic Jam Assist (TJA), under active driver supervision, provides lane keeping, acceleration, deceleration, and stopping support on certain controlled access highways at speeds of approximately 25 mph (40 km/h) and below. It requires Dynamic Radar Cruise Control (DRCC) and Lane Tracing Assist (LTA) to be active. When TJA is operating, it is possible to take your hands off the steering wheel, but you must remain attentive and ready to take control at any time.

TJA Display Statuses in the MID:

Turning TJA On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select “Vehicle Settings”.

3. Select “TrafficJamAsst” and press “OK” to turn the system On or Off.

The Driver Monitor Alert system uses a camera to detect the position and direction the driver is facing, and whether their eyes are open or closed. If the system determines the driver is not paying attention to the road, their eyes are closed, or they have poor driving posture, a buzzer will sound and a message will be displayed to warn the driver.

To turn the system On/Off:

1. Use the arrow switches on the steering wheel to navigate to the settings menu in the Multi-Information Display (MID).

2. Select “Vehicle Settings”.

3. Select “Driver Monitor Settings”.

4. Select “Driver Monitor Alert” and press “OK” to turn the system On or Off.

Lane Change Assist provides steering assistance during a lane change signaled by the driver while Dynamic Radar Cruise Control and Lane Tracing Assist are activated. The vehicle speed must be between approximately 55 and 85 mph (90 and 140 km/h). This function should only be used on highways and expressways.

The steering assist operation can be overridden by the steering wheel operation of the driver. The lane change assist function is not designed to operate when changing lanes at exits or when merging.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select “Vehicle Settings” and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “LCA” or “Lane Change Assist” and then press “OK” to turn LCA On/Off.

(4) Press the back button to go back to the menu.

If the turn signal lever is held in the first position, the lane change direction will be displayed and the function will operate.

When approaching an intersection, pulling out of a driveway, exiting a parking area, etc., at a low speed, vehicles approaching from the left and right of the front of the vehicle can be detected and the driver informed of these vehicles.

Operation of the Front Cross Traffic Alert is controlled by the following situations:

– When the system detects a vehicle approaching from the left or right of the front of your vehicle when approaching an intersection, a notification will be displayed.

– When the system determines that your vehicle may be about to enter an intersection even though a vehicle is approaching from the left or right in front of your vehicle, a buzzer will sound and a message will be displayed to urge you to depress the brake pedal.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select “Vehicle Settings” and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “FCTA” or “Front Cross Traffic Alert” and then press “OK” to turn FCTA On/Off.

(4) Press the back button to go back to the menu.

When all of the following conditions are met, the system will be operated:

• A shift position other than P or R is selected.

• The vehicle speed is approximately 10 mph (15 km/h) or less.

• A vehicle is approaching from the left or right of the front of your vehicle at a speed between approximately 7 to 37 mph (10 to 60 km/h).

• There are no vehicles in front of your vehicle.

• The accelerator pedal is not being strongly depressed.

• The brake pedal is not being strongly depressed.

Toyota Safety Sense™ (TSS) 3.0 is a suite of safety and driver assistance technologies designed to support driver awareness, decision making, and vehicle operation. TSS includes features such as Pre-Collision System with Pedestrian Detection, Lane Departure Alert with Steering Assist, and Dynamic Radar Cruise Control.

Pre-Collision System with Pedestrian Detection (PCS w/PD) is designed to help detect a vehicle, pedestrian, bicyclist, or motorcyclist and provide an audible/visual forward-collision warning under certain circumstances. If you don’t react, the system is designed to provide automatic emergency braking.

Lane Tracing Assist (LTA) is designed to help keep the vehicle in the center of a lane. LTA assists the driver with steering control while DRCC is in use.

Lane Departure Alert with Steering Assist (LDA w/SA) detects lane markings or the road’s edge at speeds above 30 mph (50 km/h). LDA w/SA is designed to provide an audible/visual warning if an inadvertent lane departure is detected. If no corrective action is taken, Steering Assist is designed to provide gentle corrective steering for lane-keeping assistance.

Full-Speed Range Dynamic Radar Cruise Control (DRCC) is an adaptive cruise control system that is designed to be set at speeds above 20 mph (30 km/h). DRCC uses vehicle-to-vehicle distance control to help maintain a preset distance from the vehicle ahead of you.

Automatic High Beams (AHB) is designed to detect headlights of oncoming vehicles and taillights of preceding vehicles. AHB automatically toggles between high and low beams as appropriate.

Road Sign Assist (RSA) uses the forward-facing camera to recognize specific road signs, such as speed limit, stop, and yield signs. RSA provides sign information to the driver via the Multi-Information Display (MID).

Proactive Driving Assist (PDA) uses the vehicle’s camera and radar, when system operating conditions are met, to provide gentle braking and/or steering to support driving tasks such as distance control between your vehicle and a preceding vehicle, pedestrian, or bicyclist. PDA can also provide gentle braking into curves.

TSS 3.0 combines a forward-facing camera mounted in front of the inside rear view mirror and a grille-mounted radar mounted in the front grille. These sensors support the driving assist systems. Side radar sensors may also be included if equipped.

Pre-Collision Warning: When the system determines that the possibility of a frontal collision is high, a buzzer will sound and an icon and warning message will be displayed on the Multi-Information Display (MID) to urge the driver to take evasive action.

Pre-Collision Brake Assist: If the driver notices the hazard and brakes, the system may provide additional braking force using Brake Assist. This system may prime the brakes and may apply greater braking force in relation to how strongly the brake pedal is depressed.

Pre-Collision Brake Control: If the driver does not brake in a set time and the system determines that the possibility of a collision with a preceding vehicle is extremely high, the system may automatically apply the brakes, reducing speed in order to help the driver reduce the impact and in certain cases avoid the collision.

Under certain conditions, the PCS included with TSS 3.0 may also help to detect a pedestrian, bicyclist or motorcyclist in front of your vehicle using the forward-facing camera and the front radar sensor. The forward-facing camera of PCS detects a potential pedestrian, bicyclist or motorcyclist based on size, profile, and motion. However, detection may vary depending on conditions like surrounding brightness, motion, posture, size, and angle, which could prevent the system from operating.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PCS icon, then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “Warning timing” and then press “OK” to change the desired setting. Each time it is pressed, the PCS warning timing changes between “Later”, “Default”, or “Earlier”.

(4) Press the back button to go back to the menu.

Note: PCS is enabled each time the vehicle is turned on. The system can be disabled/enabled and the alert timing of the system can be changed. (Alert timing only, brake operation remains the same.)

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PCS icon, and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select the PCS icon, and then press “OK” to turn PCS On/Off.

(4) Press the back button to go back to the menu.

Press the LTA switch on the steering wheel to turn LTA ON/OFF.

Note: Operation of LTA and setting adjustments continues in the same condition regardless of power switch modes until changed by the driver or the system is reset. The LTA indicator is illuminated when LTA is on.

By detecting visible lane markings or the road’s edge at speeds above 30 mph (50 km/h), Lane Departure Alert with Steering Assist (LDA w/SA) is designed to issue a visual alert and audio or steering vibration alert if an inadvertent lane departure is detected. If the driver does not take corrective action, the Steering Assist function is designed to provide gentle corrective steering.

If the Lane Departure Alert (LDA) system detects that the vehicle is swaying, a message will be displayed and a warning buzzer will sound to urge the driver to take a break.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the LDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select the LDA icon and then press “OK” to turn LDA On/Off.

(4) Press the back button to go back to the menu.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the LDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “Alert Timing” and then press “OK” to change the desired setting. Each time it is pressed, the LDA alert timing changes “Default” or “Earlier.”

(4) Press the back button to go back to the menu.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the LDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “Alert Options” and then press “OK” to change the desired setting. Each time it is pressed, the LDA alert options changes between “Vibration” or “Beep.”

(4) Press the back button to go back to the menu.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select “Vehicle Settings” and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select the “Driver Break Suggestion” icon and then press “OK” to turn the system On/Off.

(4) Press the back button to go back to the menu.

(1) Press the “MODE” switch to select DRCC. The dynamic radar cruise control indicator will illuminate and the message “Adaptive Cruise Mode” will be displayed on the MID.

(2) Using the accelerator pedal, accelerate or decelerate to the desired vehicle speed (approximately 20 mph [30 km/h] or more), and press the “-” switch to set the set vehicle speed. The set vehicle speed will be displayed on the Multi-Information Display (MID).

To change the set vehicle speed, press the “+” (increase) or “-” (decrease) switch until the desired speed is displayed. Press and hold to continuously adjust the speed in 1 mph (1.6 km/h) increments, or use a single press to adjust in individual increments of 1 mph (1.6 km/h).

You can also press the “CANCEL” switch to cancel the speed control. Press the “RES+” switch to resume control. The speed control may also be canceled by depressing the brake pedal.

Press the vehicle-to-vehicle distance switch to cycle through the settings (Short, Medium, Long, Extra Long), which will change progressively. The actual vehicle-to-vehicle distance varies in accordance with the vehicle speed.

(1) Constant speed cruising when there are no vehicles ahead: The vehicle travels at the speed set by the driver. If the set vehicle speed is exceeded while driving down a hill, the set vehicle speed display will blink and a buzzer will sound.

(2) Deceleration cruising and follow-up cruising when a preceding vehicle driving slower than the set vehicle speed is detected: When a slower vehicle is detected, the vehicle automatically decelerates. If a greater reduction in vehicle speed is necessary, the brakes may be applied. The vehicle is controlled to maintain the set distance. If deceleration is not sufficient, a warning will sound.

(3) Acceleration when there are no longer any preceding vehicles driving slower than the set vehicle speed: The vehicle accelerates until the set vehicle speed is reached and then resumes constant speed cruising.

(4) Starting off: If a preceding vehicle stops, your vehicle will also stop (controlled stop). After the preceding vehicle starts off, pressing the “RES” switch or depressing the accelerator pedal will resume follow-up cruising.

When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the display will flash and the buzzer will sound to alert the driver. An example of this would be if another driver cuts in front of you while you are following a vehicle. Depress the brake pedal to ensure an appropriate vehicle-to-vehicle distance.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select “Vehicle Settings” then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “DRCC” and then press “OK”.

(4) Press the “< >” or directional switches to select a DRCC setting from the menu, and the press “OK” to change the desired setting.

(5) Press the back button to go back to the menu.

Intended for highway use, Cruise Control lets you drive at a preset speed. The system is designed to function at speeds greater than 20 mph (30 km/h).

(1) Press the “MODE” switch to select “Cruise Control Mode.” The cruise control indicator will illuminate.

(2) Using the accelerator pedal, accelerate or decelerate to the desired vehicle speed (approximately 20 mph [30 km/h] or more), and press the “-” switch to set the speed. The set vehicle speed will be displayed on the Multi-Information Display (MID).

To change the set vehicle speed, press the “+” (increase) or “-” (decrease) switch until the desired speed is displayed. Press and hold to continuously adjust the speed in 1 mph (1.6 km/h) increments, or use a single press to adjust in individual increments of 1 mph (1.6 km/h).

Press the “CANCEL” switch to cancel the speed control. Press the “RES+” switch to resume control. The speed control may also be canceled by depressing the brake pedal.

(1) Press the “A” switch.

(2) Turn the headlight switch to the “AUTO” or headlight “ON” position.

The AHB indicator “A” will come on when the headlights are on and the headlight switch lever is in the low beam position to indicate the system is active.

Note: Push the lever away from you to manually turn on high beams. Press the AHB switch to turn the AHB system off.

When all of the following conditions are met, the high beams will be automatically turned on (after approximately 1 second):

• Vehicle speed is approximately 21 mph (34 km/h) or more.

• The area ahead of the vehicle is dark.

• There are no oncoming or preceding vehicles with headlights or taillights turned on.

• There are few streetlights or other lights on the road ahead.

If any of the following conditions occur, the high beams will be automatically turned off:

• Vehicle speed drops below approximately 17 mph (27 km/h).

• The area ahead of the vehicle is not dark.

• Oncoming or preceding vehicles have headlights or taillights turned on.

• There are many streetlights or other lights on the road ahead.

Pull the lever rearward and then return it to its original position to switch to the low beams temporarily. The high beams will illuminate while the lever is pulled. However, after the lever is returned to its original position, the low beams will remain on for a certain period of time. Afterwards, the Automatic High Beams will be activated again.

Using the forward-facing camera and/or navigation system (if equipped), Road Sign Assist (RSA) is designed to detect certain road signs and display them on the instrument cluster. The following types of road signs can be displayed:

• Speed limit

• Do Not Enter

• No U-turn

• No Turn On Red

• Stop

• Yield

• Warning

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the RSA icon and then press “OK” to turn RSA On/Off.

(3) Press the back button to go back to the menu.

Note: If the vehicle was last turned off while a speed limit sign was displayed on the Multi-Information Display (MID), the same sign displays again when the vehicle is turned back ON.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the RSA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches to select an RSA setting from the menu, and press “OK” to select or change a desired setting.

(4) Press the back button to go back to the menu.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PDA icon and then press “OK” to turn PDA On/Off.

(3) Press the back button to go back to the menu.

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “Sensitivity” and then press “OK” to change the desired setting. Each time it is pressed, the timing options changes “Later”, “Default” or “Earlier.”

(4) Press the back button to go back to the menu.

Obstacle Anticipation Assist (OAA) is designed to detect vehicles parked on the side of the road, or pedestrians or bicyclists on the side of the road or crossing the road. Depending on the circumstances, OAA may provide mild braking and/or steering assist to control distance between the detected object and the vehicle. This system operates at vehicle speeds of approximately 20-35 mph (30-60 km/h).

To turn OAA On/Off:

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “OAA” or “Obstacle Anticipation Assist” and then press “OK” to turn the system On/Off.

(4) Press the back button to go back to the menu.

Deceleration Assist (DA) is designed to provide braking assist and gently reduce vehicle speed when the system detects preceding vehicles or certain upcoming curves in the road and the driver is not pressing on the accelerator or brake pedals. This feature operates at speeds above approximately 15 mph (20 km/h). DA does not provide steering support and will not bring the vehicle to a complete stop.

To turn DA On/Off:

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “DA” or “Deceleration Assist” and then press “OK” to turn the system On/Off.

(4) Press the back button to go back to the menu.

PDA Steering Assist (SA) is designed to detect the lines of the roadway and vary the assistance from the power steering to help the driver stay within the lane. Steering Assist does not actively steer the vehicle. This feature is designed to operate at vehicle speeds between 5-80 miles per hour and does not require DRCC to be engaged.

To turn SA On/Off:

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the PDA icon and then press and hold “OK”. The setting screen is displayed.

(3) Press the “< >” or directional switches and select “SA” or “Steering Assist” and then press “OK” to turn the system On/Off.

(4) Press the back button to go back to the menu.

The seat belt should be kept as low on the hips as possible. It should not be positioned too high on the waist. After buckling, pull the shoulder belt up to take up any slack.

If a passenger’s seat belt is fully extended, then retracted even slightly, the Automatic Locking Retractor (ALR) will prevent it from being re-extended beyond that point, unless fully retracted again. This feature is used to help hold child restraint systems securely.

To adjust the shoulder belt anchor, you can push it up. To lower it, squeeze the lock release and move it down.

On the inside of the rear door, there is a lever. Moving the lever downward to the “Lock” position will allow the door to be opened only from the outside.

Safety Connect is a subscription-based telematics service that uses Global Positioning System (GPS) data and embedded cellular technology to provide safety and security features to subscribers. Safety Connect is staffed with live agents at the Toyota response center, which operates 24 hours per day, 7 days per week.

Services for subscribers include:

• Automatic collision notification

• Stolen vehicle locator

• Emergency assistance (“SOS” button)

• Enhanced roadside assistance

(1) Press the “< >” or directional switches and select the gear icon from the Multi-Information Display (MID).

(2) Press the “< >” or directional switches and select the “Vehicle Settings” icon and then press and hold “OK”.

(3) Press the “< >” or directional switches and select “TPWS setting” and then press “OK”.

(4) Press the “< >” or directional switches and select “Tire Pressure Setting” and then press “OK”.

From here, you can choose to set by specified pressure or current pressure.

NOTE: The warning light may come on due to temperature changes or changes in tire pressure from natural air leakage. If the system has not been initialized recently, setting the tire pressures to factory specifications should turn off the light.

After navigating to the “Tire Pressure Setting” screen:

(5) Press the “< >” or directional switches and select “Setting by Specified Pressure” and then press “OK”.

Then select the desired front and rear tire pressures, select “Yes” and then press “OK”. The tire pressure warning light will slowly blink three times.

After navigating to the “Tire Pressure Setting” screen:

(5) Press the “< >” or directional switches and select “Setting by Current Pressure” and then press “OK”.

And select “Yes” and then press “OK”. The tire pressure warning light will slowly blink three times and a message indicating that tire pressure is being set will be displayed on the MID.

If the tire pressure indicator flashes for approximately 1 minute and then remains on, take the vehicle to your local Toyota dealer.

The spare tire and tools are located under the floor of the trunk. Depending on the vehicle model (Type A or Type B), the arrangement of the jack, wheel nut wrench, jack handle, and wheel lock key may vary, but they are all stored with the spare tire.

(1) Remove the tool tray that sits above the spare tire.

(2) Loosen the center fastener that secures the spare tire to remove it.

The trunk lid can be opened by pulling up the glow-in-the-dark lever located on the inside of the trunk lid. The lever will continue to glow for some time after the trunk lid is closed.

Your vehicle comes standard with the Star Safety System™, which combines:

• Anti-lock Braking System (ABS)

• Brake Assist (BA)

• Electronic Brake-force Distribution (EBD)

• Smart Stop Technology (SST)

• Traction Control (TRAC)

• Vehicle Stability Control (VSC)

Toyota’s Anti-lock Brake System detects which wheels are locking up and limits wheel lockup by “pulsing” each wheel’s brakes independently. Pulsing releases brake pressure repeatedly for fractions of a second. This helps the tires attain the traction that current road conditions will allow, helping you to stay in directional control.

Brake Assist is designed to detect sudden or “panic” braking, and then add braking pressure to help decrease the vehicle’s stopping distance. When there’s only a split second to react, Brake Assist can add additional brake pressure more quickly than just the driver alone can.

Toyota’s ABS technology has Electronic Brake-force Distribution (EBD) to help maintain control and balance when braking. EBD responds to sudden stops by redistributing brake force to enhance the braking effectiveness of all four wheels.

Smart Stop Technology automatically reduces engine power when the accelerator and brake pedals are pressed simultaneously under certain conditions. SST engages when the accelerator is depressed first and the brakes are applied firmly for longer than one-half second at speeds greater than five miles per hour. SST doesn’t engage if the brake pedal is depressed before the accelerator pedal, allowing vehicles to start on a steep hill and safely accelerate without rolling backward.

Enhanced Vehicle Stability Control provides cooperative control of the ABS, TRAC, VSC and EPS. Enhanced VSC helps to maintain directional stability when loss of traction occurs during a turn.

VSC helps prevent loss of traction during cornering by reducing engine power, and Traction Control helps maintain traction on loose gravel and wet, icy, or uneven surfaces by applying brake force to the spinning wheel(s). Toyota’s TRAC sensors are activated when one of the drive wheels starts to slip. TRAC limits engine output and applies the brakes to the spinning wheel. This transfers power to the wheels that still have traction to help keep you on track.

To keep your floor mat properly positioned, follow these steps:

• Only use Toyota floor mats designed for your specific model.

• Only use one floor mat at a time, using the equipped fasteners to keep the mat in place. Always align the triangle marks on the fastener and mat.

• Install floor mats right side up.

The Toyota app allows access to valuable information about your vehicle and control of capable features equipped with your vehicle. Features include:

• Manuals & Warranties

• Schedule Maintenance

• Roadside Assistance

• Vehicle Health Report

• SiriusXM® Radio

• Safety Recalls

• Toyota Financial Services – Vehicle Payment

Remote Connect equipped vehicle functions (*if equipped):

• Lock/Unlock

• Start Vehicle*

• Vehicle Finder

• Guest Driver settings

• Hazard Lights On*

• Horn Alert*

• Buzzer Alert*

• Lock/Unlock Hatch*

• Remote Climate*

• Digital Key*

You can search for “Toyota” at your applicable app store (Apple App Store or Google Play). If you have a Toyota Owner’s account, use your credentials to “Sign In”. If you do not have an account, “Register” now to get started with the Toyota app.

Note: Do not attempt the Bluetooth® Pairing process while driving.

STEP 1: Select the [GEAR ICON] from the main menu, then “Bluetooth & Devices.”

STEP 2: Ensure Bluetooth is turned on for your phone.

STEP 3: On the vehicle’s screen, select “Manage devices”, then “Search for devices.”

STEP 4: Your phone should appear in the “Available devices” list on the vehicle screen. Select your “Device name” to register.

STEP 5: A PIN code will be displayed on the vehicle screen. Check that this PIN code matches the PIN code displayed on your Bluetooth® device, and then select [OK] on the vehicle screen.

STEP 6: If your device supports Apple CarPlay / Android Auto, a prompt will appear on the vehicle screen. Select “Yes” to enable.

STEP 7: While pairing your device, a message may display on the vehicle screen asking to check your device to allow syncing contacts and allow messaging. You may need to operate your phone to grant these permissions.

STEP 8: On your phone’s Bluetooth settings for the vehicle connection, turn on “Show Notifications” for iPhone® or “ON” for Android.

STEP 9: A confirmation will appear on the vehicle screen once your phone has been paired and connected.

• (SOS) EMERGENCY ASSISTANCE BUTTON

• AUTOMATIC COLLISION NOTIFICATION

• ROADSIDE ASSISTANCE

• STOLEN VEHICLE LOCATOR

The following features are available if the vehicle is equipped:

• START VEHICLE*

• VEHICLE STATUS ALERTS

• HAZARD LIGHTS ON*

• BUZZER ALERT*

• REMOTE CLIMATE*

• LOCK/UNLOCK VEHICLE DOORS

• VEHICLE FINDER

• HORN ALERT*

• LOCK/UNLOCK HATCH*

• DIGITAL KEY*

Completing the registration process is required to enable Remote Connect.

The following services are available if the vehicle is equipped:

• VEHICLE HEALTH REPORT

• VEHICLE MAINTENANCE ALERT NOTIFICATION

Completing the registration process is required to enable Service Connect.

• CLOUD NAVIGATION

• DESTINATION ASSIST

• INTELLIGENT ASSISTANT

Multiple mobile devices

• Connect up to 5 Wi-Fi enabled devices

• Passengers can use smartphones, laptops and tablets

Infotainment

• Browse the internet

• Send and receive email

• Stay connected on social media

• Access favorite apps

• Stream movies

STEP 1: Ensure Siri® is enabled on your phone.

STEP 2: Plug a compatible iPhone® into the USB media port using an Apple® approved cable or have the smartphone and vehicle connected through Bluetooth®.

STEP 3: On the multimedia system, select “Yes” when asked if you would like to Enable Apple CarPlay®.

STEP 4: Select Allow to use CarPlay® while the phone is locked.

STEP 5: To launch Apple CarPlay®, select the Apple CarPlay® icon on the top of the side menu bar.

STEP 6: Apple CarPlay® is now ready to operate. You can go back to the Toyota multimedia system by using the Toyota icon in the Apple CarPlay® screen.

Note: Bluetooth® functions will be inoperable while CarPlay® is in use. Wireless CarPlay® is supported.

Press and hold the voice command talk switch on the steering wheel for 2-3 seconds to activate. Once Siri® is activated you can ask to: make calls, send and receive text messages, listen to music and more.

STEP 1: With Android 9 or below, the Android Auto™ app download is required. With Android 10, Android Auto™ is built in and the app is NOT required.

STEP 2: Open Android Auto™ app and tap get started.

STEP 3: Ensure Android Auto™ is enabled on the phone.

STEP 4: Plug a compatible Android™ smartphone into the USB media port using an Android approved cable or have the smartphone and vehicle connected through Bluetooth®.

STEP 5: On the multimedia system, select “Yes” when asked if you would like to Enable Android Auto™.

STEP 6: To launch Android Auto™, select the Android Auto™ icon on the top of the side menu bar.

STEP 7: Android Auto™ is now ready to operate. You can go back to the Toyota multimedia system by using the Toyota icon in the Android Auto™ screen.

Requirements: Bluetooth® functions will be inoperable while Android Auto™ is in use. Wireless Android Auto™ is supported. Features may vary by vehicle model and phone.

Press and hold the voice command talk switch on the steering wheel for 2-3 seconds to activate. Once Google Assistant is activated, you can ask to: make calls, send and receive text messages, listen to music and more.

Toyota vehicles equipped with SiriusXM® come with a 3-month trial subscription. You get 425+ channels, including 165+ channels in your vehicle to enjoy ad-free music, plus sports, news, talk, comedy and more. Experience even more on the SiriusXM® App, featuring a collection of podcasts, Xtra channels of music, personalized Pandora® stations, SiriusXM video and more.

The Toyota Audio Multimedia system is capable of over-the-air, over Wi-Fi®, and through USB flash drive updates. To use this function it is necessary to opt-in to the Connected Service Master Data Consent. When the system software is updated, the operating methods of functions may change. Each update will identify the proper updating method to one or all of the following methods:

• Update the software using the Data Communication Module (DCM)

• Update the software using Wi-Fi

• Update the software using a USB flash drive