THULE VENTURE 933 (01) PDF MANUAL

THULE VENTURE 933 (01) PDF SUMMARY:

What should be done before installing the bike carrier?

Clean the trunk/hatch and rear of the car.

---

Where can I find the recommended fit number for my vehicle?

Look up your vehicle in the Fit Guide (included with these instructions) for the recommended fit number.

---

What should I do after finding the correct fit number in the Fit Guide?

Remove both 2 Wing Adjustment Knobs and adjust to the correct fit numbers.

---

How should the carrier arms be inserted into the hub?

With buttons squeezed in, firmly slide the carrier arms into the hub.

---

How should the carrier arms be rotated once inserted?

Rotate the arm until the button engages in the hub.

---

What should I check after rotating the carrier arms?

Ensure that buttons are visibly engaged in the hub when finished.

---

How do I install the cradle strap?

Install the cradle strap as illustrated.

---

How should the bottom straps be attached?

Attach bottom straps (narrow, grey hooks) according to the Fit Tips for your car. Always make sure that straps are out of the way of hot exhaust gases and not in contact with the muffler or exhaust pipe.

---

What should I check when positioning the lower arm of the carrier?

Be sure the lower arm is in the correct position.

---

How do I mount the carrier to the back of the vehicle?

Mount the carrier to the back of the vehicle. Refer to Fit Tips for specific placement instructions.

---

What is the correct position for the carrier arms?

Arms should be level or pointing slightly upward.

---

How should I attach the top strap?

Attach the top strap according to the Fit Tips for your car.

---

How do I tighten the top straps?

Tighten top straps, by pulling on the loose end, so the carrier stays in position.

---

What should I do if a versa clip is required?

If a versa clip is required for proper mounting, go to step 15 before continuing.

---

How much should I tighten the straps?

Tighten straps only enough to hold the rack in place without changing its position as instructed in the fit tips.

---

How do I attach the side straps?

Attach side straps to the side seams of the trunk, hatch, or door.

---

What should I do after attaching all straps?

Retighten all straps to ensure a snug fit to the vehicle.

---

What do I do with the loose ends of the straps?

Roll up loose strap ends and secure.

---

How do I secure the straps around the bike frame?

Ensure straps are tightened securely around bike frame.

---

What should I check regarding the bicycle wheels after mounting?

Ensure adequate ground clearance for bicycle wheels.

---

What should I do when loading bikes?

Alternate direction of bikes when loading.

---

Which bike should be loaded first?

Load the heaviest bike first onto the innermost cradle.

---

How can I adjust the cradles?

Cradles can be either rotated or shifted on bars to accommodate different bike geometries.

---

How do I attach the anti-sway cage?

To attach the anti-sway cradle, hold horizontal with the smooth edge facing down and slide the C-slot opening onto the bottom cradle bar. Swing down to the vertical position. Place the smooth curved surface against the bicycle down-tube and attach the strap as shown.

---

How should all bikes be secured to the rack?

Using the blue load strap provided, secure all bikes to the frame of the rack as illustrated.

---

How do I release the arms for bike arm storage?

Squeeze buttons on the hub to release arms.

---

What should I do with the arms after releasing them?

Rotate arms down.

---

What should I check after rotating the arms down for storage?

Ensure buttons are engaged in the hub when finished.

---

How do I use the versa clip?

Remove the upper strap from the carrier buckle. Thread the loose end through the slot in the hook. Pull the strap through. Open the hatch/trunk. Hang the hook inside the trunk or vehicle. Close hatch, pull strap tight and install carrier (steps 6-9).

---

What should I check before every trip?

Make sure all knobs, bolts, screws, straps, and locks are firmly attached, tightened, and locked before every trip.

---

What should be periodically inspected for signs of wear, corrosion, and fatigue?

Knobs, bolts, screws, straps, and locks must be periodically inspected for signs of wear, corrosion, and fatigue.

---

What should be checked during stops during the trip?

Check your load at stops during the trip to ensure continued fastening security.

---

What should I be aware of regarding the width and height of my cargo?

Be aware of the width and height of your cargo since low clearance branches, bridges, and parking garages can affect the load.

---

When should Thule racks and accessories be removed?

Remove your Thule rack and accessories when they are not in use and before entering automatic car washes.

---

How often should locks be turned and moved?

All locks must be turned and moved periodically to ensure smooth operation.

---

What should I use to help with smooth operation of the locks?

Use graphite or dry lubricant to help this.

---

What should I do with valuable gear if the vehicle is unattended?

Remove valuable gear if your vehicle is unattended for an extended period.

---

Where should I place at least one key?

Place at least one key in the glove compartment.

---

What driving practices should I follow for safety?

Obey all posted speed limits and traffic cautions. Adapt your speed to the conditions of the road and the load being carried.

---

What should loads be secured with?

All loads must be secured using the provided straps.

---

Where should bicycle tires be kept away from?

Keep bicycle tires away from hot exhaust.