SONY BRAVIA KDL-22BX320 (04) PDF Document

To clean the screen of your SONY BRAVIA KDL-22BX320, be sure to unplug the power cord first. Wipe the LCD screen gently with a soft cloth. Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water. Never use strong solvents such as a thinner, alcohol or benzine.

Sudden temperature changes may cause moisture condensation on your SONY BRAVIA KDL-22BX320. This may cause the TV to show poor picture or poor color. Should this occur, allow the moisture to evaporate completely before powering the TV on.

Connect the 75-ohm coaxial cable from your antenna or cable system to the CABLE/ANTENNA input on the rear of your SONY BRAVIA KDL-22BX320.

It is strongly recommended that you connect the CABLE/ANTENNA input on your SONY BRAVIA KDL-22BX320 using a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm twin lead cable can easily be affected by radio frequency interference, resulting in signal degradation.

To reset your SONY BRAVIA KDL-22BX320 to factory default settings: Turn on the TV. While holding down the up arrow button on the remote, press the power button on the TV set. The TV will turn itself off, then back on again. Release the up arrow button when the TV is on. Note that this will clear all customized settings including the Parental Lock.

If you lose or cannot remember the password for your SONY BRAVIA KDL-22BX320, enter the master password: 4357. This password clears your previous password and allows you to enter a new one.

You can adjust the volume on your SONY BRAVIA KDL-22BX320 by using the VOL +/- buttons on the remote control or the volume buttons on the TV panel.

Press the MUTING button on the remote control to mute the sound on your SONY BRAVIA KDL-22BX320. Press the button again or press the VOL + button to restore the sound.

Press the INPUT button on your SONY BRAVIA KDL-22BX320 remote control repeatedly to toggle through the list of available external inputs and TV mode.

Your SONY BRAVIA KDL-22BX320 supports the following formats for USB playback:

Photo: JPEG (files with the extension .jpg and conforming to DCF 2.0 or Exif 2.21).

Music: MP3 (files with the extension .mp3 that have not been copyrighted).

Video: MPEG1, MPEG2 (files with the extension .mpg).

To run Auto Program on your SONY BRAVIA KDL-22BX320, press the HOME button, select Settings, then go to Channel settings and select Auto Program.

You can turn on closed captions on your SONY BRAVIA KDL-22BX320 by pressing the CC button on the remote control to cycle through the available settings: On, Off, and On when Muting.

Press the WIDE button on your SONY BRAVIA KDL-22BX320 remote control repeatedly to cycle through the available wide mode settings.

The Scene Select button on your SONY BRAVIA KDL-22BX320 optimizes picture and sound quality based on the content genre. Options include Cinema, Sports, Photo, Music, Game, Graphics, General, and Auto.

While tuned to the channel on your SONY BRAVIA KDL-22BX320, press the HOME button, select Favorites, then highlight Add to Favorites and press the center button.

To use PIP on your SONY BRAVIA KDL-22BX320, press the OPTIONS button while in PC mode, select PIP, and the sub window will appear.

To swap audio in PIP mode on your SONY BRAVIA KDL-22BX320, press the OPTIONS button, select Audio Swap, and then highlight the window you want to be audible.

On your SONY BRAVIA KDL-22BX320, press the HOME button, go to Settings, then Setup, and select Label Video Inputs under AV Setup to assign labels to your connected equipment.

To change automatic shut-off settings on your SONY BRAVIA KDL-22BX320, check the Sleep Timer setting under the Setup menu or the Idle TV Standby and Auto Shut Off settings under the Eco Settings menu.

Ensure your connected equipment supports Control for HDMI. On your SONY BRAVIA KDL-22BX320, go to Settings, Setup, HDMI Settings, and set Control for HDMI to On. Then use the SYNC MENU button to control your connected devices.

The Light Sensor on your SONY BRAVIA KDL-22BX320 detects ambient room light levels and automatically adjusts the screen brightness to optimize picture quality and power consumption.

On your SONY BRAVIA KDL-22BX320, go to the Parental Lock settings menu and select Channel Block. You will need to enter your password to access these settings.

Yes, you can use your SONY BRAVIA KDL-22BX320 as a PC monitor by connecting an HD15-HD15 cable to the PC IN jack or by using an HDMI connection.

Your SONY BRAVIA KDL-22BX320 provides several power-saving levels under the Eco Settings menu: Off, Low, High, and Picture Off. Selecting High will reduce power consumption more than other settings.

To fine-tune color on your SONY BRAVIA KDL-22BX320, go to Picture Settings, then Advanced Settings, and select White Balance to make manual adjustments.

On your SONY BRAVIA KDL-22BX320, go to the Sound Settings menu, select Speakers, and set it to Audio System. This will disable the TV’s internal speakers and route audio to your external system.

On your SONY BRAVIA KDL-22BX320, navigate to the Product Support menu in the Settings and select Signal Diagnostics to view information for the current signal.

If you have no sound on your SONY BRAVIA KDL-22BX320, check the volume level, ensure Muting is not active, and check that the Speakers setting in the Sound menu is set to TV Speakers.

On your SONY BRAVIA KDL-22BX320, go to the Setup menu and select Language to choose between English, Español, or Français.

Go to the Channel Settings menu on your SONY BRAVIA KDL-22BX320 and select Show/Hide Channels to customize which channels appear when using the CH +/- buttons.

The Favorites list on your SONY BRAVIA KDL-22BX320 will be automatically cleared each time you perform an Auto Program scan.

To view PC content on your SONY BRAVIA KDL-22BX320, it is recommended to set the Scene Select to Graphics, Wide Mode to Full, and Display Area to Full Pixel.

To adjust the sharpness of the image on your SONY BRAVIA KDL-22BX320, go to the Picture Settings menu and modify the Sharpness option.

The Picture Off setting on your SONY BRAVIA KDL-22BX320 turns off the screen while maintaining audio. This is found in the Eco Settings menu.

Go to the Setup menu, select AV Setup, then Label Video Inputs on your SONY BRAVIA KDL-22BX320 to select and rename your inputs.

Yes, for the SONY BRAVIA KDL-22BX320, use only the compatible Wall-Mount Bracket (SU-WL100). Always have the installation performed by a professional and ensure the wall can support four times the weight of the TV.

You can check the software version of your SONY BRAVIA KDL-22BX320 by navigating to the Product Support menu within the Settings section.

To move the picture position vertically on your SONY BRAVIA KDL-22BX320, go to the Screen Settings menu and use the Vertical Center option (available in certain modes).

In the Picture Settings menu of your SONY BRAVIA KDL-22BX320, you can select from Cool, Neutral, or Warm 1/Warm 2 under the Color Temperature setting.

CineMotion on your SONY BRAVIA KDL-22BX320 improves picture movement and reduces graininess for film-based content. Select Auto to let the TV optimize this automatically.

You can disable the power-on sound on your SONY BRAVIA KDL-22BX320 by setting the Start-up Sound option to Off in the Setup menu.

On your SONY BRAVIA KDL-22BX320, navigate to the Setup menu and select Sleep Timer to choose between 15, 30, 45, 60, 90, or 120 minutes.

In the Sound Settings menu of your SONY BRAVIA KDL-22BX320, set the Sound Mode to Custom, then select Equalizer to adjust your specific frequency response curves.

Yes, your SONY BRAVIA KDL-22BX320 supports digital closed captioning. You can configure these settings under the Setup menu under Closed Captions (CC) and then Digital CC Options.

Navigate to the Parental Lock settings on your SONY BRAVIA KDL-22BX320 and choose External Input Block to restrict access to connected inputs.

The Display Area settings on your SONY BRAVIA KDL-22BX320 allow you to choose between Full Pixel, +1, Normal, or -1 to control how the image fits the screen.

In the Channel Settings menu on your SONY BRAVIA KDL-22BX320, select Label Channels. Use the directional buttons to select the channel number and the label characters.

If you are using your SONY BRAVIA KDL-22BX320 as a PC monitor, go to the PC settings menu and select Reset to restore default values.

Your SONY BRAVIA KDL-22BX320 offers Surround sound effects such as Cinema, Music, Sports, and Game. These can be adjusted in the Sound Settings menu.

Yes, you can adjust the backlight intensity of your SONY BRAVIA KDL-22BX320 via the Backlight option in the Picture Settings menu.

If you are experiencing poor picture quality on an analog channel on your SONY BRAVIA KDL-22BX320, navigate to the Channel Settings menu and select Analog Fine Tune to adjust the tuning manually.