SAXA 940800-090 (01) PDF Document

For the SAXA 940800-090, you should only use deep cycle batteries as the power source. Both AGM lead-acid batteries and LiFePO4 lithium batteries are suitable. Incorrect or improper use or connection of the battery may cause damage. It is also advised to disconnect the battery when the boat is stored or not in use for an extended period.

When operating the SAXA 940800-090 electric bow motor in shallow water or near obstacles, you should reduce your speed. Raise or pull up the motor in shallow areas. Always be aware of any swimmers in the vicinity of your boat.

After using your SAXA 940800-090, remove any debris from around the propeller and propeller shaft. If the motor has been used in saltwater, it should be rinsed with fresh water. Note that when used in brackish water with low salinity, the motor does not need to be rinsed after every use.

To install the propeller on your SAXA 940800-090:

Step 1. Install the drive pin and align the cross-shaped slots on the propeller with the corresponding parts on the motor.

Step 2. Install the sacrificial anode, stainless steel washer, and self-locking nut onto the drive shaft.

Step 3. Hold the propeller to prevent it from rotating and use the provided propeller wrench to tighten the nut until it is firmly in place. Do not overtighten. The nut should be tightened no more than 1/4 turn after it is “snug.” Overtightening may damage the propeller.

ATTENTION: Use only the propeller wrench provided. Other tools may overtighten and damage the components.

To install the fin on your SAXA 940800-090, first ensure the motor is disconnected from the battery. The nuts, bolts, and fin are provided in a separate plastic bag. Align the fin with the bottom of the motor, making sure the direction is correct before tightening the nuts and bolts.

Before installing the SAXA 940800-090, make sure the battery is disconnected. The motor can be bolted directly to the boat, or if you are using a quick-release plate, attach the plate to the boat. It is recommended to install the motor so that it is aligned longitudinally with the boat or at a slight angle. The motor should be installed as horizontally as possible to operate at its best. The closer the motor is positioned to the boat’s keel line in the driving position, the more efficiently it will move the boat and hold it in position with the sky anchor.

To connect the SAXA 940800-090 to a battery:

1. Use only a deep-cycle battery with the correct voltage (12V). Both lead-acid and lithium-based batteries are suitable.

2. Connect the battery’s positive (+) terminal (red wire) and negative (-) terminal (black wire) to the corresponding motor connectors. The ring terminal should be positioned as low as possible, under the washer.

3. Always ensure the battery is securely fastened and not in contact with metal objects. Using a battery box is recommended.

WARNING: Always disconnect the motor from the battery when charging the battery. Charging without disconnecting may damage the motor’s electronics.

For the SAXA 940800-090, it is recommended to install a 60 A circuit breaker between the battery’s positive terminal (+) and the motor’s red power cable (+). The circuit breaker protects the motor in case of a fault and prevents damage.

Lowering the motor:

Press the lift/lower pedal and gently lower the motor, making sure that the bottom of the depth adjustment ring aligns with the steering collar.

Raising the motor:

Press the foot pedal, grab the motor shaft, head, or body, and lift while pulling back horizontally until the motor clicks into the bracket.

WARNING: During lifting and lowering operations, keep your fingers away from all hinges and joints. Do not let the motor drop freely; lower it in a controlled manner to avoid damage.

To adjust the depth of the SAXA 940800-090, hold the motor shaft, loosen the depth adjustment ring nut, and adjust the motor to the desired depth. Tighten the nut once the depth is correct. When transporting the boat on a trailer with the motor in place, always lock the depth adjustment ring at the gearbox level (the lower end of the shaft) and support the shaft near the top.

To pair the remote with your SAXA 940800-090, press and hold the pairing button on the motor (located below the battery indicator lights) and the minus button on the remote control simultaneously for three (3) seconds. Release both buttons when you hear 3 beeps, which confirms a successful connection.

The status indicator light on the remote for your SAXA 940800-090 works as follows:

1. Press the “ON” button: The light stays on or blinks, indicating the remote is in standby mode.

2. Press any button: The red indicator light blinks, indicating signal transmission.

3. Select the anchor button: The light turns two-tone pink/purple, indicating the motor is in anchor mode (Spot Lock).

4. Press the “OFF” button: The indicator light will turn off.

ATTENTION: If you press the “ON” button and the light does not turn on or stays red continuously, the remote control battery is empty and needs to be charged.

To control the speed of your SAXA 940800-090:

• Press the motor activation button (middle button), then tap the + or – buttons to adjust the motor speed.

• To reach full speed, press and hold the + button.

• To stop the motor, press the motor icon (middle button) again.

To use the Spot Lock function on your SAXA 940800-090, press the anchor button on the remote. This will activate the function, which holds the boat in place. Press the anchor button again to deactivate Spot Lock, which will return the motor to stop mode. After pressing the Spot Lock button, you can use the speed buttons to select the desired speed for holding position.

When you press the cruise direction button on the remote for your SAXA 940800-090, the boat will move in the direction it was heading at that moment. You can press the left or right arrow buttons to adjust the travel direction. To exit the mode, press the cruise direction button again.

To charge the remote for your SAXA 940800-090, remove the waterproof protective cap and connect the provided USB charging cable. The USB end of the cable has a charging status light:

• Red light = charging

• Green light = fully charged

ATTENTION: When charging the remote control for the first time, the light may quickly turn green. Leave the device charging overnight or for several hours. Use only the provided charging cable. The remote can be used for an average of 48 hours continuously. If your boat has a USB charging port, you can use the remote while it is charging.

The SAXA 940800-090 motor features a battery status indicator with 3 LED lights that shows the charge level of the connected battery (100%, 50%, 20%). It is recommended to recharge the battery when the charge level drops to 20%, especially for lead-acid batteries.

If you are using a lithium battery, it contains a Battery Management System (BMS). When the battery reaches its maximum allowed depth of discharge (DoD), it will automatically cut off power. Please note that with lithium batteries, the charge level indicator may not always be completely accurate due to the nature of lithium battery discharge. Many lithium batteries include a Bluetooth function to monitor the exact charge level via a mobile app.

If your SAXA 940800-090 fails to start or seems underpowered, check the following:

• Ensure that the power cable is properly connected.

• Check that the battery terminals are clean and free from corrosion.

• Make sure the battery is fully charged. If it is empty or has low voltage, recharge the battery.

• Check that no fishing line or vegetation is tangled around the propeller. Disconnect the motor from the battery before cleaning and removing any debris.

• Ensure that the propeller drive pin is in good condition.

If your SAXA 940800-090 is vibrating, follow these steps:

• Make sure the propeller is installed correctly. Check the condition of the propeller and the drive pin or shear pin and replace any worn parts if necessary.

• Disconnect the battery and try rotating the propeller by hand. The propeller should rotate freely without significant resistance.

If there is strong resistance or the propeller is jammed, contact service or your dealer.

An overload warning on the SAXA 940800-090 is indicated by a continuous beep. This may be caused by an excessive load, such as a heavy boat or an obstruction in the propeller. Additionally, if the battery voltage drops too low, the motor will shut off to protect itself.

The audio signals for the SAXA 940800-090 indicate the following statuses:

To properly maintain your SAXA 940800-090, follow these steps:

1. Thoroughly wash and clean the motor and propeller after each use, especially after use in saltwater. Regular cleaning is highly recommended to ensure long-term, trouble-free operation.

2. Remove debris such as aquatic plants from around the propeller and propeller shaft after each use.

3. Regularly lubricate moving parts with appropriate lubricant and use proper tools to secure parts when necessary.

4. Apply corrosion protection regularly to protect the motor.

5. Store the motor in a dry and well-ventilated area. The motor can be stored in almost any position.

6. Do not place heavy objects on top of the motor.

7. This product is intended for outdoor use only.

8. This motor is designed for recreational outdoor use. Continuous professional long-distance boating powered by this electric motor is not permitted.