RADIOSHACK 2604734 (01) PDF Document

The RADIOSHACK 2604734 mouse has the following components:

Top View:

• Left click button

• Right click button

• Middle key contact roller (scroll wheel)

• DPI button

• Return to desktop button

• Charging reminder light

• LOGO light

• Receiver storage compartment

Bottom View:

• Type-C charging port

• Optical engine

• Mouse switch (Power ON/OFF)

• Mode light

• Device key change button

To connect using the USB receiver, follow these steps:

1. Open the front cover of the mouse to take out the USB receiver.

2. Insert the receiver into your computer’s USB port and wait a few seconds for the driver to automatically install.

3. Switch the mouse power switch on the bottom to “ON”.

4. Short press the dual mode button (labeled as 12 in the manual) repeatedly until the Mode light (11) turns red and flashes. The red light will turn off after the mouse is connected successfully.

5. Move the mouse or press the left and right buttons to begin using it normally.

The RADIOSHACK 2604734 mouse can connect to two different devices via Bluetooth (BT1 and BT2).

1. Switch the power at the bottom of the mouse to ON.

2. Press the dual mode button (12) to select either BT1 or BT2. The corresponding light will flash to indicate it is in pairing mode (green for BT1, blue for BT2).

3. Open your tablet, computer, or phone’s Bluetooth settings.

4. Select the Bluetooth interface and click “RS2604734 CH1” (for BT1) or “RS2604734 CH2” (for BT2) to connect. The light will turn off, signaling that it is connected successfully.

5. Move the mouse or click the left and right buttons to use it normally.

To reconnect to a previously paired Bluetooth device, you can long press the device key change button for 2 seconds.

To switch between three connected devices (2.4GHz, Bluetooth 1, and Bluetooth 2), press the device switch button (12) on the bottom of the mouse. The corresponding mode light will flash before turning off, enabling normal operation on the selected device.

Charge the mouse via the computer’s USB interface using the Type-C charging port. The charging reminder light will flash during charging and remain on when fully charged.

Please follow these charging instructions:

1. Charge the mouse using the computer’s USB interface.

2. Avoid using fast-charging mobile phone chargers.

3. Do not use low-quality, non-standard power adapters.

4. Refrain from using power adapters with overvoltage or overcurrent.

5. Keep away from high-temperature equipment while charging.

6. Do not charge the mouse while in use.

7. The red indicator light will be on during charging and will turn off when charging is complete.

8. Turn off the power switch if the mouse will not be used for an extended period.

Connection Mode Lights (Mode light):

• Flashing Red: The mouse is in 2.4G pairing mode.

• Flashing Green: The mouse is in Bluetooth 1 (BT1) pairing mode.

• Flashing Blue: The mouse is in Bluetooth 2 (BT2) pairing mode.

The light turns off once the connection is successful.

Charging and Battery Lights (Charging reminder light):

• Flashing Light: The mouse is charging.

• Solid Light: The mouse is fully charged.

• Last Grid of Battery Light Flashes: This is a low voltage prompt, indicating the mouse is about to run out of power and needs to be charged.

The charging reminder also displays the charge level when charging (25/50/75/100%).

1. If the mouse cursor moves slowly, check the battery level and charge it promptly. A flashing light on the last grid of the battery indicator signals low power.

2. If the mouse won’t connect, ensure the power switch on the bottom is on, select the correct connection method (2.4G, BT1, or BT2), or try a different USB port for the receiver.

The mouse will automatically enter sleep mode after a period of inactivity to conserve power. To wake it up, simply move the mouse or press any key.

To further conserve power, you can manually turn off the power switch on the bottom of the mouse if it is not in use for an extended period.

• Do not disassemble or modify the product, except for battery removal and replacement.

• Disassembling or attempting repairs may cause damage.

• Avoid pointing infrared or laser beams at eyes or reflective surfaces.

• Do not immerse the product in liquids or expose it to hot or humid conditions.

• If the product is exposed to temperatures outside the specified range, disconnect the power until it stabilizes within the operating range.

• This product should be used with certified ITE computers and accessories.

• It is not suitable for children under 14 years old.

• Prolonged use for repetitive actions may cause nerve or muscle damage. If you experience pain, numbness, weakness, swelling, burning, cramps, or stiffness, consult a healthcare professional.

• Under normal conditions, this product poses no safety hazards. For malfunctioning issues, contact support. Ensure an authorized service center handles any necessary repairs.

• Do not disassemble or attempt to repair the product, as this may cause damage.