NEMCO 9101A (01) PDF Document

When using the NEMCO 9101A, basic safety precautions should be followed, including the following:

1) Read all instructions before using the appliance.

2) Read and follow the specific “PRECAUTIONS TO AVOID POSSIBLE ELECTRIC SHOCK”.

3) This appliance must be grounded. Connect only to a properly grounded outlet.

4) Use this appliance only on the specified electrical circuit.

5) Install or locate this appliance only in accordance with the provided installation instructions.

6) Do not heat any sealed cans on the induction range. A sealed can may explode.

7) Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors on this appliance.

8) As with any appliance, close supervision is necessary when used by or around children.

9) Do not operate this appliance if it has a damaged cord or plug, broken or cracked glass surface, if it is not working properly, or if it has been damaged or dropped.

10) This appliance should be serviced only by qualified service personnel.

11) Do not cover or block any openings on the appliance. Allow 4″ clearance from all vent openings.

12) Do not place the range in, on or near open flames, electric burners, ovens or other high temperature surroundings.

13) Do not move the range while cooking or while hot.

14) Do not store this appliance outdoors. Do not use this product near water – for example, near a kitchen sink, in a wet basement, near a swimming pool, or similar locations.

15) Do not immerse cord or plug in water.

16) Keep cord away from heated surfaces.

17) Do not let cord hang over edge of table or counter.

18) When cleaning, use only mild, nonabrasive soaps or detergents applied with a sponge of soft cloth.

19) Do not clean with metal scouring pads. These will scratch and damage the glass and control surfaces.

20) Do not touch the hot surface of the glass cooktop.

21) Do not heat empty pots/pans. Using an empty pan can result in extremely high temperatures that may damage the pan and the range.

22) Keep pacemakers at least 2 feet from the cooktop.

1. Plug the unit into the appropriate power outlet. The display will show four red dots when voltage is present.

2. Press the red power on/off button. The display will show ‘00’ and the unit is now in the ready state.

3. Place an appropriate pan on the glass cooktop, centering it on the target.

4. Press the ‘Start/Stop’ button. The display will show ‘5’ or ‘6’, and the fan will start. The range is now warming or cooking at the displayed power level.

5. Rotate the knob to the right to increase the power setting.

6. Rotate the knob to the left to decrease the power level.

7. For the NEMCO 9101A Warming Unit, the power will adjust from H1 to H7. See the chart for approximate holding temperatures. Power levels H1 thru H7 are hold settings, designed to keep food warm at a constant temperature for serving.

8. While warming, press the ‘Start/Stop’ button to stop the cooking cycle, or remove the pan. If the pan is removed and replaced within approximately 40 seconds while the ‘00’ symbol is flashing, the system will automatically resume heating. After 40 seconds with no pan, the display will show a steady ’00’. Pressing ‘Start/Stop’ will resume operation if the pan is present.

9. The power level can be adjusted ‘on the fly’ at any time while the unit is heating.

10. When the unit is turned off using the Power On/Off button, the cooling fan may continue to operate for a short period of time.

11. Do not unplug the unit until the fan has stopped running.

The NEMCO 9101A will not operate without an appropriate pan or vessel in place on the cooktop. After a few seconds, the display will flash ‘00’ indicating that no pan is present. If the pan is removed during cooking, the unit will turn off after about 40 seconds and the display will show ‘00’. To resume cooking, place the pan back on the cooktop and press the ‘Start/Stop’ button.

If the temperature of the cooktop reaches 260° C or 500° F, the NEMCO 9101A will turn off automatically and display an error code. This can happen if a pan is empty or is allowed to boil dry. Allow the unit to cool off, then restart it by pressing the power on/off button.

If the voltage or current in the NEMCO 9101A is abnormal, it will shut itself off and display an error code.

Small objects such as a knife or spoon will not be ‘seen’ as a valid pan by the NEMCO 9101A, and it will not operate. However, you should not place items other than induction cookware on the range surface.

The following chart shows an approximate temperature guide for the NEMCO 9101A warming unit. Results will vary depending on the type of pan, and the type and volume of food being held.

Warmer Setting	H1	H2	H3	H4	H5	H6	H7
Temp °F	95	105	122	140	160	180	195

Temperature control mode is not available on this model. If you press the ‘Mode’ button the display will show ‘000F’, but it will have no effect on the operation of the unit. Pressing the ‘Start/Stop’ button in this mode will result in an ‘E5′ error message after a few seconds. Press the red ‘Power’ button to turn the unit off and clear the error message.

The timer function on the NEMCO 9101A allows you to set a timer from 1 second up to 719 minutes. The timer resets to 719 minutes every time the power is turned off/on. The timer always runs in the background, so if the unit runs continuously for 12 hours (719 minutes), the timer will run out and the unit will turn off. To reset, turn the power off/on, or manually set the timer.

• With the unit powered on and in the Ready state (display shows a steady ’00’), press the ‘TMR’ button. The display will show ‘0719’.

• To change the timer setting, press the ‘MIN/SEC’ button. The display will flash ‘719’.

• Turn the knob to adjust the number of minutes. Turning the knob to the left will reduce the number of minutes. If you turn the knob to the right past 719, the display will go to ‘00.59’ or 59 seconds. Keep turning to the right to increase the minutes.

• If you want to set seconds, for instance 3 minutes and 30 seconds, turn the knob until the display shows ‘03.59’ minutes. Then press the ‘MIN/SEC’ button again. The ‘seconds’ field will flash. Use the knob to adjust the seconds to 30. The display will show ‘03.30’.

• When the time is set to what you want, press the ‘Start/Stop’ button. The power will come on and the timer will count down. When the timer counts down to 0, the unit will stop heating.

• While the unit is heating, the display will alternate between the timer and the power setting. You can always adjust the power setting while the display is showing the power level.

• If you press the TMR button while the unit is heating, the display will stop alternating between the timer and the power level. The timer will continue to run. Pressing the TMR button again will resume alternating the display.

• While the unit is heating, the timer display decimal points will flash.

• Once the timer counts down to zero, pressing the ‘Start/Stop’ button will restart the cycle at the time that you set previously. Turning the unit off/on using the ‘Power’ Button will reset the timer to 719 minutes.

After the NEMCO 9101A has cooled down, clean as follows:

Glass Cooktop: Wipe with a damp cloth or use a mild, non-abrasive cleaning solution.

Control Panel: Wipe with a damp cloth only. Do not spray with cleaning solutions! Do not use sharp or metal objects to press the buttons! Only press the buttons using your finger!

DO NOT USE SHARP OBJECTS OR ABRASIVES ON THE GLASS COOKTOP. SCRATCHES IN THE GLASS CAN WEAKEN IT AND LEAD TO BREAKAGE!

Cooking with the NEMCO 9101A requires the use of induction compatible pots/pans. In general, this means that the vessel must be magnetic. If a magnet sticks to it, it will probably be a good induction pan.

Other things to consider are the size and shape of the pan:

• Pans should have a minimum bottom diameter of 4.75 inches.

• The bottom of the pan should be flat within about 1/8 of an inch.

• For best results, the maximum bottom diameter of the pan should not exceed 10.25 inches.

Materials that will NOT work with induction ranges include glass, ceramics, earthenware, bronze, copper, aluminum, or 300 series stainless steel.

To test a pan for compatibility, place it on the range, press the Start button, and increase the power level. If the display flashes ’00’, the pan is not compatible with induction cooking.

Model	9101A
Frequency	50/60Hz
Voltage	120
Amps	2.2
Power	270 W
Weight	14 lbs.
Dimensions	L 14 9/16″ W 11 5/8″ D 3 1/8″

Always ensure that the glass surface of the range is mounted FLUSH with the counter top. The exposed edge of the glass is fragile and can be easily chipped or broken by side impact.

If flush mounting is not feasible, you can purchase the optional Stainless Steel Trim Ring which allows you to make a simple cut-out in the counter top. The Trim Ring supports the unit and protects the glass edge from damage.

With either mounting method, seal around the unit (and Trim Ring) with silicone caulking to keep liquids from penetrating and getting below the surface.

If the units are mounted in a closed cabinet, you must ensure that there is adequate air flow. Each unit draws in cooling air from the back and exhausts warm air from the front. In a closed cabinet, you must provide adequate openings for both the intake and the exhaust air.

Flashing Display Indication	Cause	Solution
U	No pan or non-induction pan	Place an appropriate pan on the cooktop target
1	Over current	Check for abnormal conditions like water, moisture or broken parts or cord. Unplug the unit. Plug it back in. If the error continues, contact customer service.
2	Over Voltage	Check to verify that the outlet voltage is correct and within limits. Unplug the unit. Plug it back in. If the error continues, contact customer service.
3	Under Voltage	Check to verify that the outlet voltage is correct and within limits. Unplug the unit. Plug it back in. If the error continues, contact customer service.
4	Main Heat Sink Over Temp	Check to verify that the fans are working. Check to make sure the air flow is unrestricted.
5	External Temp. Probe problem	Temp mode not available on BKT series.
6	Pan is Overheated	Make sure the pan is not empty. Allow the unit to cool down.
7	Power Frequency is Unstable	Check the incoming power for frequency stability. Unplug the unit. Plug it back in. If the error continues, contact customer service.
8	OP Amp Offset Error	Unplug the unit. Plug it back in. If the error continues, contact customer service.
9	Main Coil Overcurrent	Unplug the unit. Plug it back in. If the error continues, contact customer service.