PIONEER DDJ-WEGO (01) PDF MANUAL

1. Turn on the computer’s power.
2. Insert the included CD-ROM into the computer’s CD drive.
3. When the CD-ROM menu appears, select [Install Driver Software (Pioneer_DDJ_WeGO_Driver_X.XXX)], then click [Start].
4. Proceed with installation according to the instructions on the screen. If [Windows Security] appears on the screen while the installation is in progress, click [Install this driver software anyway] and continue with the installation.

• If [Hardware Installation] appears on the screen while the installation is in progress, click [Continue Anyway] and continue with the installation.
• When the installation program is completed, a completion message appears.

1. Connect this unit to your computer via a USB cable.
2. Slide this unit’s [ON/OFF] switch to the [ON] position. Turn on the power of this unit.

• The message [Installing device driver software] may appear when this unit is first connected to the computer or when it is connected to a different USB port on the computer. Wait a while until the message [Your devices are ready for use] appears.

This unit functions as an audio device conforming to the ASIO standards.

• If an application using this unit as the default audio device (DJ software, etc.) is running, quit that application before adjusting the buffer size.

Click the Windows [Start] menu>[All Programs]> [Pioneer]>[DDJ_WeGO]>[DDJ_WeGO ASIO Settings Utility].

• If the buffer size is made large, drops in audio data (breaks in the sound) occur less easily, but the time lag due to the delay in the transfer of the audio data (latency) increases.
• If the kernel buffer number is made large, breaks in the sound occur less easily, but the time lag due to latency increases.

If there are no interruptions in the sound with the default settings

1. Gradually decrease the buffer size, setting it to the minimum value at which there are no interruptions in the sound.
2. Set the kernel buffer size to [2] and check whether there are interruptions in the sound. If there are interruptions in the sound, set the kernel buffer size to [3].

If there are interruptions in the sound with the default settings

1. Set the kernel buffer size to [4], then set the buffer size to the minimum value at which there are no interruptions in the sound.

1. Insert the included CD-ROM into the computer’s CD drive.
2. When the CD-ROM’s menu is displayed, select [Install VIRTUAL DJ LE(DDJ-WeGO)], then click [Start]. The VIRTUAL DJ LE installer is launched.
3. Once the VIRTUAL DJ LE installer is launched, click [Next].
4. Read the contents of the [End-User License Agreement] carefully, and if you agree, check [I accept the terms in the License Agreement], then click [Next].
5. Select the type of installation for VIRTUAL DJ LE, then click [Next].
6. When the screen below is displayed, click [Install].
7. Click [Finish].
8. Enter the serial number printed on this unit’s bottom panel (XXXX-XXXX-XXXXX/WEGO), then click [OK].

1. Insert the included CD-ROM into the computer’s CD drive. The [CD_menu] icon appears on the screen. Double-click it.
2. When the CD-ROM’s menu is displayed, select [Install VIRTUAL DJ LE(DDJ-WeGO)], then click [Start]. The VIRTUAL DJ LE installer is launched.
3. Once the VIRTUAL DJ LE installer is launched, click [Continue].
4. Read the contents of the license agreement carefully, click [Continue] and then click [Agree] to accept the license agreement.
5. Select the type of installation for VIRTUAL DJ LE, then click [Install]. To select standard installation, click [Install]. To install in a different location, click [Change Install Location…] and choose the place of installation.
6. Click [Close].

1. USB terminal – Connect to a computer.
2. ON/OFF switch – Turns this unit’s power on and off.
3. PHONES terminals – Connect headphones here.
4. MIC jack – Connects a microphone here.
5. Kensington security slot
6. MASTER OUT terminals – Connect powered speakers, etc., here.

• Turn: The cursor moves in section A of the diagram.
• [SHIFT] + turn: The cursor moves in section B of the diagram.
• [SHIFT] + press: Folders in section B of the diagram open and close.

• Press: Sets a cue point or moves the cue point.
• [SHIFT] + press: The playing position moves to the beginning of the track.

• Press: Synchronizes to the master deck’s tempo.
• [SHIFT] + press: Sets the master deck for synchronization.

• Press: Turns key control on and off.
• [SHIFT] + press: Turns key control, the filter and effects 1 to 3 all off at once.

• Press: Turns the filter on and off.
• [SHIFT] + press: Turns key control, the filter and effects 1 to 3 all off at once.

• Press: Turns effect 1 on and off.
• [SHIFT] + press: Switches the effect types of FX1.

• Press: Turns effect 2 on and off.
• [SHIFT] + press: Switches the effect types of FX2.

• Press: Turns effect 3 on and off.
• [SHIFT] + press: Switches the effect types of FX3.

• Turn: Changes the loop length for playback.
• Press: Turns loop playback on and off.
• [SHIFT] + turn: Moves the beat grid position.
• [SHIFT] + press: Sets the manual loop’s in and out points. Turns manual loop playback on and off.

• Press: When the sampler mode is off, sets or calls out the hot cue point. When the sampler mode is on, plays/stops playback of the sample sound.
• [SHIFT] + press: When the sampler mode is off, cancels the hot cue set at the button that is pressed. When the sampler mode is on, if a sample sound is playing, playback returns to the beginning of the sample sound and continues from there.

• Scratch – When turned while touching a metallic part of the top of the jog dial, the sound is played according to the direction and speed at which the jog dial is turned.
• Pitch bend – The playing speed can be adjusted by turning the outer part of the jog dial during playback.
• Manual search – When the jog dial is spun while pressing [SHIFT] button during playback, the track is fast-forwarded/fast-reversed.

1. Connect this unit to your computer via a USB cable.
2. Boot up the connected computer.
3. Slide this unit’s [ON/OFF] switch to the [ON] position.

1. From the Windows [Start] menu, click the [All Programs] > [VirtualDJ] > [VirtualDJ LE (DDJ-WeGO)] icon.
2. Click [CONFIG] in the top right of the computer’s screen. The [Settings] screen appears. Settings should be selected on the [Sound Setup] tab in the following order:
   1. [Inputs]: Select [NONE].
   2. [Sound card]: Select [ASIO DRIVER] and [Pioneer DDJ_WeGO ASIO].
   3. [Outputs]: Select [HEADPHONES] and [Master: Chan 1&2/Headphones: Chan 3&4].
3. Click [Apply], then click [OK].

1. In Finder, open the [Application] folder, then double-click the [VirtualDJ LE] icon.
2. Click [CONFIG] in the top left of the computer’s screen. The [Settings] screen appears. Settings should be selected on the [Sound Setup] tab in the following order:
   1. [Inputs]: Select [NONE].
   2. [Sound card]: Select [4-OUT CARD] and [Pioneer DDJ-WeGO].
   3. [Outputs]: Select [HEADPHONES] and [Master: Chan 1&2/Headphones: Chan 3&4].
3. Click [Apply], then click [OK].

1. Turn the rotary selector while pressing the [SHIFT] button to select a folder or item.
2. Release the [SHIFT] button then turn the rotary selector to select the track.
3. Press the [LOAD] button to load the selected track onto the deck.
4. Press the [►/II] button to play the track.

1. Operate the channel faders to adjust the audio level output from the respective decks.
2. Operate the crossfader to switch the deck whose sound is output from the speakers.
   • Left edge: Sound is output from deck [A] or [C].
   • Center: The sound of all the decks is mixed and output.
   • Right edge: Sound is output from deck [B] or [D].
3. Turn the [MASTER VOL] control to adjust the audio level of the speakers.

1. Connect headphones to the [PHONES] terminal.
2. Press the [CUE ?] button for the deck you want to monitor.
3. Turn the [HEADPHONES MIX] control.
   • Turn counterclockwise: The volume of the deck whose [CUE ?] button is pressed increases relatively.
   • Turn clockwise: The [MASTER OUT] volume increases relatively.
4. Turn the [HEADPHONES VOL] control.

1. Operate the [TEMPO] slider to match the playing speed on one deck to the playing speed on the other deck.
   • Move towards the + (front) side: The playing speed increases.
   • Move towards the – (back) side: The playing speed decreases.
2. If the beats of the two decks are off, use the jog dial’s pitch bend function to correct for this offset. The playing speed can be adjusted by turning the outer part of the jog dial during playback.
   • Spin clockwise: The playing speed increases.
   • Spin counterclockwise: The playing speed decreases.
   • Stop spinning: Playback at the normal speed resumes.
3. Operate the channel faders or crossfader to mix the sound of the two decks and switch between them.

1. Connect the microphone to the [MIC] terminal.
2. Adjust the audio level input to the [MIC] terminal.

1. Quit VIRTUAL DJ LE.
2. Slide this unit’s [ON/OFF] switch to the [OFF] position.
3. Disconnect the USB cable from your computer.

This unit is equipped with 5 types of JOG FX modes.

1. Press the [COLOR] button.
2. Select the desired background color.
3. Select the desired jog color.

1. In the pause mode, press the [CUE] button to set a cue point at the position at which playback is paused.
2. During playback, press the [CUE] button to return to the last operated hot cue point and pause there (Back Cue).
3. After returning to the cue point, keep pressing the [CUE] button to continue playing (Cue Sampler).

1. During playback, press the [AUTO LOOP] control while pressing the [SHIFT] button to set the loop in point.
2. After the loop in point is set, press the [AUTO LOOP] control while pressing the [SHIFT] button to set the loop out point and start loop playback.

1. During playback, turn the [AUTO LOOP] control to set the length for loop playback in number of beats.
2. Press the [AUTO LOOP] control to start loop playback.

1. During playback or in the pause mode, press a [HOT CUE (DELETE)/SAMPLER] button to set a hot cue.
2. Press the [HOT CUE (DELETE)/SAMPLER] button at which the hot cue is set to call out the hot cue.