PIONEER DDJ-WEGO2 (01) PDF MANUAL

1. Turn on the computer’s power.
2. Insert the included CD-ROM into the computer’s CD drive. The CD-ROM menu is displayed. If the CD-ROM menu does not appear when the CD-ROM is inserted, open the CD drive from [Computer (or My Computer)] in the [Start] menu, then double-click the [CD_menu.exe] icon.
3. When the CD-ROM menu appears, select [Install Driver Software (Pioneer_DDJ_WeGO2_Driver_X.XXX)], then click [Start].
4. Proceed with installation according to the instructions on the screen. If [Windows Security] appears on the screen while the installation is in progress, click [Install this driver software anyway] and continue with the installation. After installing the driver software, install the VIRTUAL DJ LE software.
• When installing on Windows XP, if [Hardware Installation] appears on the screen while the installation is in progress, click [Continue Anyway] and continue with the installation.
5. Select [Install VIRTUAL DJ LE(DDJ-WeGO2)] from the CD-ROM’s menu, then click [Start]. The VIRTUAL DJ LE installer is launched.
6. Once the VIRTUAL DJ LE installer is launched, click [Next].
7. Read the contents of the [End-User License Agreement] carefully, and if you agree, check [I accept the terms in the License Agreement], then click [Next]. If you do not agree to the terms of the [End-User License Agreement], click [Cancel] to cancel installation.
8. Select the type of installation for VIRTUAL DJ LE, then click [Next].
• When [Typical] is selected, plug-ins and other components are installed simultaneously. Normally select [Typical].
• When [Custom] is selected, you can select which components to install.
9. When the screen below is displayed, click [Install]. Installation begins. The message of successful installation appears once installation is completed.
10. Click [Finish]. This completes the installation procedure. VIRTUAL DJ LE is launched if [Launch VirtualDJ] on the screen is checked when [Finish] is clicked.
11. Input the serial number printed on this unit’s bottom panel (XXXX-XXXX-XXXXX/WEGO2), then click [OK].

1. Connect this unit to your computer via a USB cable.
2. Slide this unit’s [ON/OFF] switch to the [ON] position. Turn on the power of this unit. The message [Installing device driver software] may appear when this unit is first connected to the computer or when it is connected to a different USB port on the computer. Wait a while until the message [Your devices are ready for use] appears.

This unit functions as an audio device conforming to the ASIO standards.

• If an application using this unit as the default audio device (DJ software, etc.) is running, quit that application before adjusting the buffer size.
• If the buffer size is made large, drops in audio data (breaks in the sound) occur less easily, but the time lag due to the delay in the transfer of the audio data (latency) increases.
• If the kernel buffer number is made large, breaks in the sound occur less easily, but the time lag due to latency increases.
• Operate referring to the procedure below to adjust the buffer size and kernel buffer.

If there are interruptions in the sound with the default settings: Set the kernel buffer size to [4], then set the buffer size to the minimum value at which there are no interruptions in the sound. If there are no interruptions in the sound with the default settings:

1. Gradually decrease the buffer size, setting it to the minimum value at which there are no interruptions in the sound.
2. Set the kernel buffer size to [2] and check whether there are interruptions in the sound.
• If there are interruptions in the sound, set the kernel buffer size to [3].

To use an iPhone/iPad, mount the included iPhone/iPad stand.

1. Remove the three screw covers.
2. Fasten the included screws in the order shown on the diagram below. Do not use any screws other than the included ones.

Cautions on using the iPhone/iPad stand

• This stand is exclusively for use with an iPhone/iPad. Do not place tablets other than iPads or large devices on the stand.
• Set the iPhone/iPad on the stand in the horizontal direction. It may be unstable if set in the vertical direction.
• Do not apply excessive force to the stand. Doing so may damage this unit.
• Do not move with an iPhone/iPad placed on the stand. The iPhone/iPad could fall off.
• If there is a cover on the iPhone/iPad, remove the cover before placing the iPhone/iPad on the stand. If the cover is left on, the iPhone/iPad could be unstable.

1. Connect this unit to your computer via a USB cable.
2. Boot up the connected computer.
3. Slide this unit’s [ON/OFF] switch to the [ON] position. Turn on the power of this unit.

1. Turn the rotary selector while pressing the [SHIFT] button to select a folder or item. When a folder or item with the [+] mark is selected and the rotary selector is pressed while pressing the [SHIFT] button, that folder or item is opened or closed.
2. Release the [SHIFT] button then turn the rotary selector to select the track.
3. Press the [LOAD] button to load the selected track onto the deck.
4. Press the [►/II] button to play the track. When this button is pressed again during playback, playback pauses.

• Adjust the volume of the powered speakers, etc., connected to the [MASTER OUT] terminals to an appropriate level. Note that if the volume is set too high, the output sound could be very loud.

1. Operate the channel faders to adjust the audio level output from the respective decks.
2. Operate the crossfader to switch the deck whose sound is output from the speakers.
• Left edge: Sound is output from deck [A] or [C].
• Center: The sound of all the decks is mixed and output.
• Right edge: Sound is output from deck [B] or [D].
3. Turn the [MASTER VOL] control to adjust the audio level of the speakers.

Turn the [EQ (HI, MID, LOW)] controls on the respective decks.

1. Quit VIRTUAL DJ LE.
2. Slide this unit’s [ON/OFF] switch to the [OFF] position.
3. Disconnect the USB cable from your computer.

1. In the pause mode, press the [CUE] button to set a cue point at the position at which playback is paused. When no hot cue is set at any of buttons [1] to [4], the cue point is simultaneously set as hot cue [1]. If hot cues have already been set, the hot cue last operated is reset at the cue point position.
2. During playback, press the [CUE] button to return to the last operated hot cue point and pause there (Back Cue).
3. After returning to the cue point, keep pressing the [CUE] button to continue playing (Cue Sampler).

Loops with a maximum length of approximately 4 seconds can be created.

1. During playback, press the [AUTO LOOP] control while pressing the [SHIFT] button to set the loop in point.
2. After the loop in point is set, press the [AUTO LOOP] control while pressing the [SHIFT] button to set the loop out point and start loop playback.

1. During playback, turn the [AUTO LOOP] control to set the length for loop playback in number of beats.
2. Press the [AUTO LOOP] control to start loop playback. The length of the loop can be changed by turning the [AUTO LOOP] control during loop playback.

With this function, playback can be started instantaneously from the position at which a hot cue is set. Up to four hot cues can be set and stored per track.

1. During playback or in the pause mode, press a [HOT CUE (DELETE)/SAMPLER] button to set a hot cue.
2. Press the [HOT CUE (DELETE)/SAMPLER] button at which the hot cue is set to call out the hot cue.

Hot cue operations can be performed when the [SAMPLER] button is not lit.

The sounds of up to 8 sampler slots can be operated in addition to deck operations. Press a [HOT CUE (DELETE)/SAMPLER] button to start playback of the sampler slot. On this unit, sampler slot operations can be performed when the [SAMPLER] button is lit. Playback returns to the beginning of the sample and continues by pressing the [HOT CUE (DELETE)/SAMPLER] button while pressing the [SHIFT] button when the sample is playing.

Press the [CUE] button while pressing the [SHIFT] button to change the color of the illumination of the jog dial. The color of the illumination changes in the order shown below.

Illumination color and Illumination mode Table

Illumination color	Illumination mode
Frosty white	Pulse Mode Active
Red
Orange
Yellow
Green
Emerald green
Aqua
Blue	Pulse Mode Normal
Violet
Off