PELONIS PFS40A4BBB (01) PDF Document

Please follow these rules for safe operation:

1. Never insert fingers, pencils, or any other object through the grille when the fan is running.

2. Disconnect the fan when moving from one location to another.

3. Disconnect the fan when removing grilles for cleaning.

4. Be sure the fan is on a stable surface when operating to avoid overturning.

5. Do not use the fan in a window. Rain may create an electrical hazard.

6. Ensure that the fan is switched off from the supply mains before removing the grille.

This appliance has a polarized plug, where one blade is wider than the other. To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.

This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.

1. Do not operate any fan with a damaged cord or plug. Discard the fan or return it to an authorized service facility for examination and/or repair.

2. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from the traffic area and where it will not be tripped over.

To assemble the base:

1. Align the column (pole) with the groove on the base.

2. Fix them together using the right-angle bolt from underneath the base.

1. Place the rear grill on the motor housing, aligning it correctly.

2. Secure the rear grill by screwing the lock nut of grill clockwise.

3. Slide the fan blade onto the motor shaft.

4. Secure the blade by screwing the lock nut of blade anticlockwise.

5. After installing, pull the blade to rotate it and ensure that it can be normally rotated.

1. Align the screw holes on the outer ring of both the Front and Rear Guards, with the Positioning Clip aligned as illustrated in the manual.

2. Press down all the Buckles to fasten the Front Guard with the Rear Guard.

3. At the Screw Holes, tighten the separated screw and nut to secure the guards together.

The remote controller has the following keys:

“ON/OFF” key: Turns the fan on or off.

“SPEED” key: Cycles through the available fan speeds.

“TIMER” key: Sets the auto-off timer.

The effective range of the remote control is within a 5-meter distance and a 30-degree deflection in front of the product.

The display lights indicate the fan’s current settings:

Speed display: A series of lights indicate the selected fan speed.

Timer display: Lights labeled 1h, 2h, and 4h will illuminate to show the total time set for the fan to automatically turn off.

The fan body has three control buttons:

ON/OFF: Press to turn the fan on or off.

SPEED: Press to cycle through the fan speed settings.

TIMER: Press to set the auto-off timer.

To control the horizontal swing, use the Swing Pull-knob located on top of the motor housing:

To stop oscillation (static): Pull the knob up.

To start oscillation (swing): Push the knob down.

To adjust the vertical angle of the fan, manually tilt the fan head up or down to your desired position.

To adjust the fan’s height, locate the Height Adjustment Key on the pole. Turn the key counterclockwise to loosen the pole. Adjust the fan to the desired height, and then turn the key clockwise to tighten and lock it in place.

a) Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.

b) Open the fuse cover. Slide the fuse access cover on top of the attachment plug towards the blades.

c) Remove the fuse carefully. Insert the tip of your tool into the fuse slot (close to the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel it is tight, you can try it several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely.

d) Risk of fire. Replace fuse only with a 2.5 Amp, 125 Volt fuse.

e) Close the fuse cover. Slide the fuse access cover on top of the attachment plug closed.

f) Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Notice:

1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damaged or cause an accident.

2. When you feel it is hard to operate, please make sure you have got the right way.

1. Be sure to unplug from the electrical supply source before cleaning.

2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly remove soap film with clean water.

3. Be sure not to allow water or other liquid to enter the inside of the motor.