Free English PCE INSTRUMENTS PCE-ACO 9500 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PCE INSTRUMENTS PCE-ACO 9500 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the safety instructions for the PCE INSTRUMENTS PCE-ACO 9500 Air Compressor?
To avoid fire, hurt body, electric shock, and other accidents, please read and follow these safety instructions before using the PCE INSTRUMENTS PCE-ACO 9500:
1. Keep the work place clean.
2. Do not put the machine in wet or harsh conditions (dusty or full of explosive gas).
3. Electric shock: Do not touch grounded objects, such as conduit pipes, heating pipes, etc.
4. Keep kids and unrelated people away from the machine when it is working.
5. When not in use, release the air and dust water from the tank and store it in a dry place.
6. Please follow the rating volt and speed.
7. Cable Protection: Do not tighten the power cable and keep it away from hot resources and oil.
8. Maintenance: Clean the filter, check the cable and accessories. If not in good condition, please exchange them. Turn off the power source and the switch of the air compressor when not in use.
9. Avoid over-pressure setting: The maximum pressure for the PCE-ACO 9500 is 0.9Mpa.
10. Warning: Please use our factory’s parts for repair.
11. Power volt: Check the voltage, such as 100V – 120V. If not correct, the machine will be damaged by abnormal voltage.
13. The compressor is only for air pressurization, not for other gas, dust, or explosive material.
14. Do not use forced flammable and combustible air and liquid.
15. Do not touch the hot parts of the compressor, such as the motor cover, exhaust pipe, etc.
16. The cable section should not be less than 2 square mm and not be excessively long.
17. It is forbidden to crash. Please place it in a suitable position when you work with it.
What are the main parameters of the PCE INSTRUMENTS PCE-ACO 9500 Air Compressor?
| Model | Pressure | Flow | Rated Power | Voltage | N.W. | Speed |
| PCE-ACO 9500 | 0.3-0.9Mpa | 125L/min | 1000W | AC110V | 7.5kg | 2800Rpm |
What are the main features of the PCE INSTRUMENTS PCE-ACO 9500?
The main features of the PCE INSTRUMENTS PCE-ACO 9500 are:
1. Air Line Outlet
2. Safety Valve
3. Sensor
4. Silencer
5. Solenoid Valve
6. LCD control panel
How do I operate the LCD Controller System on the PCE INSTRUMENTS PCE-ACO 9500?
1. Pressure Setting Scope: The pressure can be set between 0.3-0.9Mpa. The system will start working automatically if the pressure falls lower than 10% of the set scope.
2. Voltage: Please choose the right voltage, 100V-120V.
3. Start/Stop: Use the On/Off button to start and stop the machine.
4. Speed Adjustment (Fast/Silence): The Fast/Silence button adjusts the working speed.
– Fast Mode: The speed is 3000rpm, and the display shows a running speed of 99%.
– Silence Mode: The speed is 1500rpm, and the display shows a running speed of 50%.
5. Adjusting Pressure: Use the left arrow (“+”) and right arrow (“-“) buttons to adjust the setting pressure. One press adjusts the pressure by 5 Psi. For example, if the setting pressure is 100Psi, the machine will start once the pressure drops below 90Psi.
6. Stopping the Machine: When not in use, press the on/off button to stop the machine.
How do I set up the PCE INSTRUMENTS PCE-ACO 9500 for use?
1. When unwrapped from the carton, pull up the stopper.
2. Install the silencer.
3. First, connect the air tools you need, then start the machine.
What is the use scope and efficiency of the PCE INSTRUMENTS PCE-ACO 9500?
The maximum loading power of the PCE INSTRUMENTS PCE-ACO 9500 can drive 2 pcs F30 Pneumatic Nailers.
Common applications include:
– Woodworking Pneumatic Nailer
– Tire air charging
– Pneumatically cleaning dust
– Pneumatic Screwdriver
What are the maintenance procedures for the PCE INSTRUMENTS PCE-ACO 9500?
ATTENTION: All maintenance processes must be done after stopping the power and exhausting all of the air. Otherwise, it could hurt your body.
1. Please keep the machine clean and perform termly maintenance.
2. Safety valve: Regularly check the safety valve. If it is not good, replace it.
3. Filter and Piston Cup: Clean the silencer’s filter every 500 hours. The piston cup should be exchanged every 5000 hours. The LCD shows the work time to help track this.
What does fault code E01 mean on the PCE INSTRUMENTS PCE-ACO 9500?
The fault code E01 indicates an overvoltage or low-voltage protection error.
What is the detailed parts list for the PCE INSTRUMENTS PCE-ACO 9500?
| S/N | CODE | NAME & SPECIFICATION |
| 1 | 1330033 | Hexagonal nail M6X30 (three) |
| 2 | 3900397 | Solenoid valve group |
| 3 | 2500690 | Up lid(right) |
| 4 | 2190268 | Check valve |
| 5 | 4200219 | Square washer(right) |
| 6 | 1310049 | Cross recessed pan head screw |
| 7 | 2500693 | Piston cup fastener |
| 8 | 2200417 | Valve block |
| 9 | 2500697 | Center cover(right) |
| 10 | 2200316 | Small square gasket 10 X 12 X 0.6 |
| 11 | 1310084 | Cruciform head head screw |
| 12 | 2190149 | Silencer |
| 13 | 4200162 | O-ring ￠ 63 X 3 ￠ |
| 14 | 2130045 | Cylinder ￠ 69 X ￠ 63.7 X 24.5 |
| 15 | 1360003 | Hexagon socket countersunk head screws M8X20 |
| 16 | 2500699 | Piston cup fastener(right) |
| 17 | 4200165 | Piston cup ￠ 48 X ￠ 68 X 0.8 |
| 18 | 2500457 | Piston |
| 19 | 1100141 | Deep groove ball bearing6006RS/SYBS |
| 20 | 1330047 | Hexagon socket cap screwsM5×20 |
| 21 | 1340006 | Hexagon socket set screw M8 |
| 22 | 2200317 | Fastener |
| 23 | 2190143 | Crank |
| 24 | 1310040 | Cross recess pan head screw(three) |
| 25 | 4101032 | Handle |
| 26 | 2190148 | 26 2190148 Aluminium pipe ￠ 12.6 X 117.5 2 |
| 27 | 4200163 | O-ring ￠ 10 X ￠ 2 |
| 28 | 4101033 | Handle cover |
| 29 | 1200005 | Cross recessed pan head tapping screws ST4X16 |
| 30 | 2500691 | Up cover(left) |
| 31 | 4200218 | Square washer(left) |
| 32 | 2500696 | Center cover(right) |
| 33 | 2190144 | Straight joint(G1/4) |
| 34 | 2190145 | Copper four-way connection(G1/4) |
| 35 | 2190189 | Coupling(G1/4) |
| 36 | 2190165 | Safety valve(G1/4) |
| 37 | 3900371 | Sensor(G1/4) |
| 38 | 1310080 | Cross recess pan head screw M4×14 |
| 39 | 4100902 | Fans cover |
| 40 | 1500015 | Shaft ring ￠ 14 |
| 41 | 4100903 | Fan A |
| 42 | 1600026 | Hexagon nut with flange M4 |
| 43 | 2500452 | Tank 1 |
| 44 | 1100142 | Deep groove ball bearing 6203RS/CW |
| 45 | 3110161 | Stator |
| 46 | 3900380 | Hall plate |
| 47 | 1310068 | Cross recessed pan head screw M4×95 |
| 48 | 3110162 | Rotor |
| 49 | 2500453 | Tank 2 |
| 50 | 1310069 | Cross recessed pan head screw M4×145 |
| 51 | 4100904 | Fans B |
| 52 | 4200164 | Rubber shock pad |
| 53 | 1400066 | Gasket ￠ 6 X ￠ 14X1 |
| 54 | 1310032 | Cross recessed pan head screw M6×20 |
| 55 | 5400867 | Power label |
| 56 | 2500449 | Aluminium case for main board |
| 57 | 1310040 | Cross recess pan head screw M4×14(three) |
| 58 | 3900382 | Main board |
| 59 | 1310065 | Cross recess pan head screw M3×10(three) |
| 60 | 1200040 | Cross recessed pan head tapping screw ST2×6-C |
| 61 | 1200053 | Cross recessed pan head tapping screw ST2.5×8-C |
| 62 | 3210097 | Power line with jacket 3×0.75×2.6m |
| 63 | 5400868 | Nameplate |
| 64 | 3900344 | LCD control pannel |
| 65 | 4100905 | Cover of main board |
| 66 | 5400869 | Label for operation |
How should the PCE INSTRUMENTS PCE-ACO 9500 and its batteries be disposed of?
For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament applies. Due to the contained pollutants, batteries must not be disposed of as household waste. They must be given to collection points designed for that purpose.
To comply with the EU directive 2012/19/EU, devices should not be disposed of as household waste. They can be returned for re-use or given to a recycling company that disposes of devices in line with the law. For countries outside the EU, batteries and devices should be disposed of in accordance with your local waste regulations.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD PCE INSTRUMENTS PCE-ACO 9500 (01) PDF DOCUMENT