ORBEGOZO ADR 71 (01) PDF DOCUMENT

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must never play with the appliance. Cleaning and user maintenance must never be carried out by children without supervision.

2. Children should be supervised to ensure that they do not play with the appliance.

3. Keep the appliance and the cable cord out of the reach of children less than 8 years old.

4. WARNING: In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

5. If the supply cord is damaged it must be repaired by the Authorized Service Agent in order to avoid hazards.

6. Never pull on the cord when unplugging.

7. Do not use the unit with a damaged cord or plug, or if it is not working properly.

8. Do not handle the appliance with wet hands.

9. Never immerse the appliance in water or any other liquid.

10. Make sure the appliance has been unplugged before cleaning.

11. This appliance must be installed following the national regulations for electrical installations.

12. This appliance is for household use only.

13. In case that you need a copy of the instruction manual, you can find it in the provided documentation.

14. WARNING: In case of misuse, there is a risk of possible injury.

The R290 refrigerant gas complies with European environmental regulations.

This device contains approximately 175g of R290 refrigerant gas.

The maximum nominal surface area is 330 m3/h.

Do not perforate or damage.

Use only utensils recommended by the manufacturer to defrost or clean.

Do not use the appliance in a home with any ignition sources that are in continuous operation (for example, gas appliances in operation or an electric heater in operation).

Do not perforate any components in the refrigerant circuit.

The refrigerant gas may be odorless.

An area greater than 9 m2 is required for installation, use and installation of the device.

Possible leaks of refrigerant gas in homes without ventilation could cause a fire or possible explosion if the refrigerant comes into contact with electrical heaters, estufas or other ignition sources.

Keep the appliance in place to avoid mechanical failures.

You can only work in refrigerant circuits for authorized persons who are competent and accredited by an agency that certifies them for refrigerant handling, in conformity with the legislation of the sector.

All maintenance and repairs that require the assistance of your qualified personnel must be carried out under the supervision of specialists in the use of flammable refrigerants.

Please leave the product sitting outside the box for 24 HOURS before plugging it in. The product may have been tilted or placed upside down during shipping. Leave the product for 24 hours so the oil in the compressor can settle from the move. Not doing so can affect the performance or life span of the product.

The functions act just like the touch controls on the air conditioner. All key functions can be accessed from the remote control. Do not leave the remote control exposed to direct sunlight.

Press this key to turn on the machine, and then press it to turn off. To boot the system, press the Power key once. The buzzer will beep, and the display and various instructions will light up accordingly. The function keys on the panel can be operated at this time.

The ORBEGOZO ADR 71 has three work modes: Cool (cold), Dehu (dehumidifier) and Fan (fan). Each time the MODE key is pressed, the operating mode and the light indicator for each mode change. The modes change in the following order: Cool → Dehu → Fan.

The TIMER is used to configure a timed start or shutdown up to 24 hours.

Press the SLEEP button to activate or deactivate this mode. When the device is in sleep mode, the air speed automatically changes to low. In this mode all the lights turn off except the “Sleep” indicator which remains slightly lit. In sleep mode, press the Sleep key to stop it.

In the power on/off state, long press the “LOCK” key for 3 seconds to activate or deactivate the child lock. Once the lock is activated, no key will work except “Lock”, which must be pressed again for 3 seconds to unlock the keyboard.

Press the SPEED key once to select low or high air speed. The corresponding indicator icons light up in the following order: Low → High.

INCREASE “+”:

In cold mode: Press to increase the temperature by 1 °C with each pulse. Hold the button to fast forward. The display will flash to show the set temperature.

Timer mode: Press this key to adjust the set time upwards, increasing by 1 hour with each press. Hold the button to fast forward. The screen will flash to show the set time.

DECREASE “-“:

In cold mode: Press to decrease the temperature by 1 °C with each pulse. Hold the button to fast forward. The display will flash to show the set temperature.

Timer mode: Press this key to adjust the set time downward, decreasing by 1 hour each press. Hold the button to fast forward. The screen will flash to show the set time.

Cold mode (Cool):

Temperature adjustment range: 17 – 30 °C.

The screen shows the set temperature.

The Cool mode indicator lights up.

You can choose the air speed between high and low.

Dehumidifier mode (Dehu):

Temperature/humidity cannot be adjusted.

The display shows “dH”.

Air speed cannot be set; it always works in low mode.

The Dehu mode indicator lights up.

The equipment automatically establishes the working conditions according to the environmental conditions.

Fan mode (Fan):

You cannot adjust the temperature.

The display shows “25”.

The Fan mode indicator lights up.

You can choose the air speed between low and high.

You can set a scheduled start in sleep (power off) state or a scheduled shutdown in a working state, up to a maximum of 24 hours.

Scheduled start/shutdown setting method:

1- Press the “Timer” key to activate the function or view the timer status, the “Timer” indicator icon will flash.

2- Press the “+” or “-” keys to adjust the set time with an interval of 1 hour.

3- If no operation is performed or any other key except “+” and “-” is pressed within 5 seconds during the “Timer” indicator flashing, the displayed value will be automatically confirmed.

This device has non-volatile memory.

If you start the equipment and a power failure occurs, it will turn on after being reconnected and will continue to operate with the previous parameters.

If the equipment is turned off before a sudden power outage, when the power returns it will remain off.

When the internal tank of the device is full of water, the “Full” icon flashes and the display shows E7, indicating that the water tank is full. At this time, the customer must turn off the equipment, drain the water, and restart so that the equipment can restore normal operation.

1. Take out the outer connector and air outlet tube and remove the plastic bags.

2. Insert the screw into the hole of window partition A.

3. Insert the window partition B into the window partition A from the side (the wing screw head needs to be stuck into the slot of the window partition B), and adjust the assembly length as required.

4. Turn over the window partition, put the gasket and wing screw in turn and tighten them.

5. Insert the wing screw into the hole of the window partition C.

6. Insert the window partition C into the window partition B from the side (the wing screw head needs to be stuck into the slot of the window partition B), and adjust the assembly length as required.

7. Turn over the window partition, put the gasket and wing screw in turn and tighten them.

8. Stretch both ends to expand the exhaust duct.

9. Turn the air Exhaust Duct Connector to one end of the exhaust duct (clockwise), and then turn the window plate connector to the other end of the exhaust duct (clockwise). Then the flexible exhaust pipe assembly is finished.

10. Insert the exhaust pipe assembly (the end of the exhaust joint) into the back-panel vent slot (push to the left) and complete the assembly.

1. Half open the window, and mount the window sealing plate assembly to the window. The assembly can be placed in a horizontal and vertical direction.

2. Pull various components of the window sealing plate assembly open, adjust their opening distance to bring both ends of the assembly into contact with the window frame, and fix various components of the assembly.

1. Place the machine on a flat and dry surface, and keep it away from objects at least 30 cm.

2. Insert the air outlet hose into the window adapter, adjust the window opening width to match the sealing plate correctly, the length is adjustable.

3. Free access to the outlet pipe is important, installation errors will negatively affect the machine.

4. Make sure that the air in the outlet tube can circulate smoothly.

Warning: The length of the outlet pipe is adapted to the characteristics of the machine, do not replace or lengthen it freely, otherwise malfunctions will occur.

Note: The extreme length of the drop down exhaust pipe is 1500mm; Shorten the length as much as possible and keep it as level as possible during installation.

Tips: The installation of the exhaust duct depends on the operating mode of the air conditioner. When the air conditioner is in Cool mode, it is necessary to install the duct, but when the air conditioner is in Fan or Dehu mode, it is not necessary to install the outlet duct. Users can compress or stretch the exhaust duct according to usage preferences. Do not extend or bend the outlet duct arbitrarily.

Install the drain hose in Dehumidifier (Dehu) mode:

In dehumidifier mode, a drain hose must be connected to the continuous drain outlet at the top of the rear of the machine.

• Remove the rubber plug from the continuous drain outlet at the top of the rear of the machine.

• Insert one end of the drain hose into the upper continuous drain outlet.

• Connect the other end of the drain hose to a drain or large capacity container. You must take into account that the drain has to be lower than the drain inlet.

Install the drain hose into the lower tank:

• To prevent the lower tank from filling in very humid environments, a drain hose must be connected to the continuous drain outlet on the underside of the rear of the machine.

• Remove the rubber plug from the continuous drain outlet at the bottom of the rear of the machine.

• Insert one end of the drain hose into the lower continuous drain outlet.

• Connect the other end of the drain hose to a drain or large capacity container. You must take into account that the drain has to be lower than the drain inlet.

Caution: To avoid electric shock, you must turn off the appliance and unplug it before performing cleaning and maintenance tasks.

1) Machine cleaning

Clean the machine with a soft, slightly damp cloth.

2) Cleaning the filter screen

• Take out the two filters (1 and 2).

• Clean the filter: Use a vacuum cleaner to gently vacuum the dust from the filter surface. If the filter grate is very dirty, clean it with warm water and a mild detergent and dry it completely.

• Replace filters 1 and 2.

3) Storage

To store the machine if it will be unused for a long time, pay attention to the following steps:

1. Remove the drain plug from the bottom pan and drain the water completely. Clean the machine body and filter grill.

2. Select “Fan” mode to dry the inside of the air conditioner completely.

3. Turn off the power switch, coil and tie the power cord.

4. Place the machine in a cool and dry environment.

Do not place the machine on soft and uneven ground to avoid vibration or movement.

Do not insert rods or hard objects into the machine to avoid failure or danger.

Keep the machine away from heat sources such as heaters and electric kettles when using it.

Close doors and windows to achieve the best cooling effect.

Do not place objects in front of and behind the machine. If the ventilation is blocked, the cooling effect will be affected.

Unplug the air conditioner when not in use for a long period of time.

Wipe the machine body gently with a damp cloth and do not shoot water directly.

Please do not put anything on the machine.

Clean the filter screen once every two weeks (never use hot water over 40°C, alcohol or gasoline).

In continuous drainage, the drain pipe must be placed in a horizontal position, without coiling.

Do not dry the filter in direct sunlight to avoid deformation.

Before moving the machine, drain any water accumulated in the lower tank.