NOMA 52-8867-6 (01) PDF Document

The NOMA 52-8867-6 digital timer includes the following features:

• Real-time clock with Weekday, Hour, Minute and Second reading

• Display in selectable 12 or 24 hour display format

• 6 on/off program pairs with Weekday, Hour and Minute setting

• Settings can operate individually either on a specific day, Monday to Friday, Monday to Saturday or every day

• Daylight Savings Time

• Manual on/off

• Master/individual disable for pre-set program(s)

The 1.5V batteries come pre-installed in the timer. To activate them, you must completely remove the piece of ribbon that is protruding from the battery compartment.

Note: The batteries serve to back up the clock and programs while the timer is unplugged. The battery life is around 1 year when the timer is not connected to a power outlet. If you plan to leave the timer unplugged for a long period of time, you may want to remove the batteries from the timer.

If the display on your NOMA 52-8867-6 timer is dim or abnormal, you should replace the button cell batteries. If the display is abnormal or blank and you wish to clear all settings, you can perform a reset.

When an abnormal or blank display appears, or if you want to clear all programs, use a round object such as a ball-point pen to push the RESET key. After the reset is complete, the clock and all programs will be cleared.

The program modes of the timer are arranged in a continuous pattern: Clock → Pgm.1 On → Pgm.1 Off → Pgm.2 On → … → Pgm.6 Off → Clock…

• The PROG symbol will light up to denote a Program is being displayed.

• Press either the Up (▲) or Down (▼) key to scroll through the clock and programs. If the key is pressed for more than 1 second, it will repeat itself.

• To return to the Clock display from any other mode, simply press both the Up (▲) and Down (▼) keys together.

1. To set the clock, press the SET key while the clock is displayed. “SET” will appear on the display and the day of the week will be flashing.

2. Press the Up (▲) or Down (▼) key to select the correct day. Hold the key to skip through the days.

3. Once the correct day has been selected, press the SET key. The Hour will begin flashing.

4. Press the Up (▲) or Down (▼) key to select the hour.

5. Press the SET key. The Minutes will begin flashing.

6. Press the Up (▲) or Down (▼) key to select the minutes.

7. Press the SET key. The Seconds will begin flashing.

8. For the setting of Seconds, either the Up (▲) or Down (▼) key will set the seconds to 00.

9. Press SET to exit the clock setting function. The “SET” display will disappear and the timer will return to the normal clock display.

To change between 12-hour and 24-hour display, press the ON/OFF and SET keys together briefly. This will toggle between the two formats.

You can set up to 6 On/Off programs. Follow this example for setting Program 1 to turn ON Monday at 8:15 and OFF at 15:45.

1. Press the Up (▲) or Down (▼) key until PROG 1 ON appears on the Display.

2. Press the SET key. “SET” will appear on the display and the Weekday will be flashing at the top of the screen.

3. Press the Up (▲) key to select the day(s) for the program to be active. The day displayed will sequence through MO-SU (everyday), MO to SU (individually), MO to FR, then MO-SA, SA-SU and repeat again. For this example, select MO (Monday).

4. Press the SET key when MO appears on the display. The Hour should be flashing.

5. Use the Up (▲) or Down (▼) key to change the hour to 8, then press the SET key.

6. The Minute should be flashing. Change it to 15.

7. Press the SET key to finish the setting of Program 1-On.

8. Press the Up (▲) key and PROG 1 OFF will appear at the display. Use the same method to set the off time (15:45).

To set more programs, press the Up (▲) key until PROG 2 ON appears and repeat the above procedures. If no key is pressed for 1 minute, the timer will return to the Clock display automatically.

To activate Summertime mode, press and hold both the Up (▲) and Down (▼) keys at the same time while in the Clock mode display. The hour will advance by one and the Summertime symbol (a sun icon) will light up.

To return to normal time, press and hold the two keys again in Clock mode.

The timer can be turned on or off at any time without affecting the programs by using the ON/OFF key. The flashing ON or OFF on the display will indicate that the Manual On/Off function is activated.

To disable one particular program:

1. Use the Up (▲) or Down (▼) keys to display the program you wish to disable (e.g., PROG 1 ON).

2. Press the SET key. The display will start flashing and the word SET will light up.

3. Press the ON/OFF key. The X symbol will appear to indicate that this particular program is disabled.

4. If the display is still flashing, press the SET key until the display is not flashing.

To re-enable the program, use the same method as above to turn off the X symbol for that program.

To disable all 6 programs (Master Disable):

1. While in the Clock display, press the SET key.

2. Then, press the ON/OFF key.

3. The X symbol will appear on the Clock Display Mode and indicate that all pre-set programs are disabled.

To cancel this Disable function and re-enable all programs, just use the same method as above to turn off the X symbol.

Program: 6 programs per day or per week

Minimum switching time: 1 minute

Ratings: 120V AC 5A

Maximum load: 600 W

Yes. This timer is equipped with a 2-pin polarized receptacle. An appliance with a 2-pin power cord is suitable to connect with it. Before plugging the timer in, it is recommended to view the correct polarization of the pin. Do not force the plug or power cord into the receptacle. Do not remove the ground pin of a 3-pin plug to plug into the timer receptacle.