LANBO LB-ERK24RC-B (01) PDF Document

Before operating the LANBO LB-ERK24RC-B for the first time, you must burn off the protective coating on the heating elements and burners. For the oven heating elements, set the temperature to 450 degrees Fahrenheit. Turn the function selector to the Bake element and the Broil element separately for approximately 15 minutes each. It is important to ensure adequate ventilation during this period.

For the burners, set the burner selector to the maximum setting for 5 minutes. Ensure there is adequate ventilation during this process. Once finished, switch off the burners and allow them to cool down completely.

To install the backsplash on your LANBO LB-ERK24RC-B, follow these step-by-step instructions:

1. Fix 2 screws (M4*8) into the corresponding holes at the back of the cover, leaving a gap of approximately 3mm.

2. Position the backsplash plate on the cover, ensuring the large holes pass over the heads of the screws.

3. Push the backsplash plate so that the small holes align with the screws.

4. Secure the assembly by tightening the screws with a screwdriver.

The anti-tip bracket prevents the LANBO LB-ERK24RC-B from tipping over if the open door is overloaded. It can be installed on either the left or right side of the appliance:

1. Place the anti-tip bracket on the floor at the location where the range will be installed.

2. Locate and mark the drill positions through the 6 holes in the bracket, then set the bracket aside.

3. Use a 5/16 inch masonry drill bit to drill two holes at a suitable depth.

4. Insert 6 plastic anchors into the holes and place the bracket back into position.

5. Secure the bracket to the floor using the supplied screws.

6. Slide the appliance into its final position.

The LANBO LB-ERK24RC-B is equipped with four ceramic surface elements. The specifications are as follows:

To operate the surface units on the LANBO LB-ERK24RC-B, lightly press the control knob inward and rotate it to the desired position. The control knobs allow for a variable power output from LO to HI. When an element is ignited, the indicator light will be lit regardless of the setting.

Important safety tips for surface units:

Never leave surface units unattended at high heat settings to avoid boil-overs that may cause smoking or greasy spillovers that could ignite.

Ensure that pan handles are turned inward and do not extend over adjacent surface units to minimize the risk of burns or unintentional contact.

Always turn all control knobs to the OFF position and ensure indicator lights are out when you are finished cooking.

The mechanical controls for the LANBO LB-ERK24RC-B oven offer the following mode settings:

To operate the oven, you must set the Cooking Mode knob, the Oven Temperature knob, and the Timer knob simultaneously for the oven to begin working.

The numbers printed on the LANBO LB-ERK24RC-B control panel indicate values in Fahrenheit. Refer to the table below for Celsius equivalents:

To facilitate thorough cleaning of the LANBO LB-ERK24RC-B, you can remove the oven door by following these steps:

1. Open the oven door to its full extent.

2. Turn the hinges as shown in the manual illustrations.

3. Hold the door firmly on both sides.

4. Gently close the door partway and withdraw the hinge pins from their location.

To replace the door, repeat these steps in the reverse order.

The storage drawer of the LANBO LB-ERK24RC-B is removable for cleaning or service access:

1. To remove: Lift the left small hook upward while simultaneously pushing the right small hook downward, then pull the drawer out.

2. To replace: Align the drawer with the rails and push it inward until it is secure.

Warning: Do not store flammable materials in the storage drawer or the oven.

If the surface cooking elements of the LANBO LB-ERK24RC-B fail to operate, check the following potential causes:

You may have blown a household fuse or tripped a circuit breaker.

Verify that you have set the control knobs correctly for the intended element.

Ensure you are pushing the surface unit control knobs in before attempting to turn them.

To maintain the LANBO LB-ERK24RC-B, follow these cleaning guidelines:

Before cleaning, disconnect the appliance from the electrical supply and ensure it is cold.

Clean the oven interior regularly using a soft cloth soaked in very hot soapy water.

For enameled parts, use a sponge with soapy water only. Avoid using chlorine-based or acidic cleaning products.

For stainless steel parts, rinse with water and dry with a soft, clean cloth, wiping along the grain direction. Use specific non-abrasive detergents for difficult dirt.

Do not use steel wool or steel brushes on the cooktop surface to avoid damage.

If your LANBO LB-ERK24RC-B features a display, it may show the following error codes:

E1: The cooling fan is defective. The range is forbidden to use.

E2: The oven temperature sensor is defective. The oven is forbidden to use, though the cooktop may still be used.

E3: Both the oven temperature sensor and cooling fan are defective. The range is forbidden to use.

E4: External power supply over-voltage. The machine automatically stops for protection. You must wait until the voltage returns to normal and the signal disappears before using the appliance again.