KOGAN KAPSNDLMAKA (01) PDF MANUAL

This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product in a safe way by the person responsible for their safety, and understand the hazards involved.

Remove the product and its accessories from the plastic envelopes, carton packages and or polystyrene parts.

Safely dispose of all packaging. To avoid a risk of suffocation, do not allow children to play with the plastic bags and polystyrene parts.

Ensure that all packaging is disposed of in accordance with your local environmental authority.

Ensure all parts are included. If any pieces are missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.

If this product or any of its components show signs of damage, cease use immediately and contact help.Kogan.com for support.

Before first use, remove all the packaging material and wash any removable components that come in contact with food (refer to “Cleaning & Care section”). Do not submerge or wash the main body with water.

Ensure that everything is completely dry before reassembling the appliance.

This product is designed for indoor use only.

Do not clean the product with steel wool, abrasive cleaners or corrosive liquids. Do not expose this appliance to extended sunlight.

Do not run this product above the capacity of ingredients outlines in the “Operation” section of this guide.

This product is intended for household usage only, it is not intended for professional use.

Avoid using this product with extension cords. If unavoidable, only use extension cords that comply with your local electrical code, of the shortest length possible.

Do not use more than one extension cord at a time.

Do not handle or use this appliance with wet hands.

Before cleaning this appliance, turn it off and unplug it from the power outlet. Remove the plug from the power outlet when not in use.

Remove the plug from the socket by holding it firmly. Do not pull it by the cable.

The voltage shown on the label of the product is present while the product itself remains connected to the socket.

Keep this product away from water. In the event it is dropped into water, do not immerse your hands in the liquid to retrieve the device without having first turned off the power and removed the plug from the wall socket.

Do not use home appliances close to bins containing liquids, taps, sinks, bathtubs, etc.

Do not immerse the main body of this product in water or any other liquid.

Do not wet the plug.

If this appliance comes in contact with water or other liquids, do not insert the plug into a power outlet. Cease use immediately and contact help.Kogan.com for support.

Do not use with any accessories other than those that have been supplied with this product.

Never hold or lift this product from power the cable.

Never twist, kink or wrap the cord around the product as this may cause the insulation to weaken and split, particularly where it enters the unit.

Keep this product away from open flames and other sources of heat.

Avoid using this product, in a corrosive and explosive atmosphere, in presence of dust or sawdust.

To avoid overheating, do not cover the appliance during operation.

This product contains high voltage components. Do not repair, disassemble, or modify the appliance in any way.

Do not use this product for any other purpose other than those outlined in this guide.

Do not insert the power plug in the wall socket until after confirming that the voltage of the socket corresponds to the voltage shown on the appliance’s compliance label.

Do not leave the appliance unattended during operation or while it’s plugged into the power outlet.

This product contains, high torque moving mechanical parts. Avoid contacting any part when it is working. Keep hands, hair, clothing, spatulas and other utensils away from moving parts during operation.

If the any parts become stuck during operation, unplug the product before attempting to remove any blockages.

Ensure the detachable parts are assembled to correctly before connecting the power.

The parts of the pasta and noodle maker and their descriptions are:

1. Top cover: Covers mixing bowl.

2. Mixing bowl: Contains flour and other ingredients.

3. Mixing axle: Mixes and kneads ingredients then extrude pasta.

4. Extruding pipe: Guides the dough towards the extrusion disc.

5. Extruding axle: Feeds the dough through the extruding pipe.

6. Screw nut: Secures extruding discs in place for operation.

7. Fastening nuts: Secures the front panel to the main body.

8. Front panel: Holds the extruding parts.

9. Drawer: Stores the extruding discs and accessories.

10. Main Body: Houses motor assembly and electrical components.

11. Flour cup: Measure flour.

12. Water cup: Measure water, vegetable juice and water/egg mixture.

13. Scraper: Scrape flour when measuring flour, cuts noodles, clean extruding discs.

The extruding discs include: Thin spaghetti, Thick spaghetti, Triangular, Penne, Small fettuccine, Medium fettuccini, Large fettuccini.

IMPORTANT! Ensure the product is disconnected from the power before assembly.

Step 1: Attach the mixing bowl to the main body.

Step 2: Attach the mixing axle into the shaft in the mixing bowl. Rotating the mixing axle slighting, can make it easier to install.

Step 3: Insert extruding pipe into front of the mixing bowl.

Step 4: Insert the extruding axle into the extruding pipe.

Step 5: Attach the front panel to the main body and secure it in place using the fastening nuts.

Step 6: Attach the required extruding disc to the front panel and secure it in place using the screw nut.

Step 7: Attach the top cover to the mixing bowl. Press it down firmly until it ‘clicks’ into place.

Before first use, ensure all removable components have been thoroughly washed and dried.

Power:

Connect the power cord to a power outlet. The machine will then be activated. Press the power button to turn on the machine.

During operation pressing the power button will stop the pasta maker and return back to standby mode.

Automatic Mode:

Depending on the amount of flour in the mixing bowl, press either the “1, 2 or 3 cups” button.

The pasta maker will start working and the LCD will display the countdown timer.

The pasta maker will knead the dough for 3 minutes before it starts the extruding process.

The machine will stop automatically and display “off” once it has finished extruding. The whole process is approximately 10 minutes.

Manual Mode:

If after running the Automatic mode, there is left over dough in the mixing bowl, press the “Manual” button to extrude the remaining dough.

The LCD will display a 5 minute countdown timer.

IMPORTANT! Do not use this function before water and flour are mixed otherwise it may cause the pasta maker to malfunction.

Carefully measure out the wet and dry ingredients. Ensure to only use the recommended ratios of flour and water.

Eggs must be mixed with the required amount of water before adding them to the flour.

Add the required ingredients to the mixing bowl following the ratios shown in the table below:

Flour	Water	Vegetable Juice (optional)	Mixture of 1 egg and water	Pasta
3 cups	160ml	160ml	170ml	480g
2 cups	100ml	100ml	110ml	320g
1 cup	60ml	60ml	70ml	160g

Do not use blended vegetables in the dough, use only juice.

Step 1: Attach the required extrusion disc. Remove the top cover.

Step 2: Fill the measuring up with the required amount of flour by pouring it directly from the flour bag to the cup, or by scooping it out with a spoon. Use the scraper to level out the flour. Do not scoop by directly putting the measuring cup into the flour bag as this can cause the flour to be packed too tightly and result in excess flour being used, leading to a dry dough.

Step 3: Pour the flour into mixing bowl.

Step 4: Replace the top cover.

Step 5: Press the “Power” button. Press automatic button according to the flour amount. Once the mixing axle begins moving, slowly pour the liquids into the mixing bowl.

Tips: Ensure to mix eggs together with water before adding them to mixing bowl. Do not add whole eggs. The resulting dough mixture should be crumbly but not dry.

Step 6: Once the dough has been properly mixed and kneaded, the noodles / pasta will begin extruding.

When extruding, the first few centimetres of dough may have rough edges and slightly abnormally shaped. This is normal and the shape of the dough will smooth out over the extrusion process.

Do not add any solid ingredients other than flour during the mixing process.

Do not open the top cover, unscrew the disc nut to open the fastening plate or touch the mixing axle by hand during operation. Doing so may cause serious injuries.

Always ensure the dough is properly mixed before using the manual function to knead and extrude any remaining dough. Doing otherwise may cause the extrusion discs to become blocked and lead to potential product damage.

This product will automatically stop after the extrusion process. If you want to make another batch of pasta, please allow the motor too cool for 20-30 minutes before proceeding.

There will be some leftover odd pieces of dough after each extrusion. To avoid food wastage, scrape the leftover pieces of dough after every extrusion and form into ball and extrude.

Ensure the pasta maker is off and disconnected from the power before disassembling.

1. Unscrew the screw nut in an anti-clockwise direction and remove the extrusion disc.

2. Press the top cover hook, lift the top cover and remove it.

3. Unscrew the two fastening nuts in an anti-clockwise direction.

4. Remove the front panel, mixing bowl, extrusion pipe, extrusion axle and mixing axle.

Ensure all the parts that came in contact with flour are thoroughly cleaned with a mix of water and a mild detergent.

Wipe all parts with a clean, dry cloth and then re-assemble.

After the machine is cleaned and assembled, store it safely away from fire, humidity, direct sunlight and children.

Do not immerse the main body in water or other liquids.

Ensure the storage drawer and all the accessories are stored clean and dry.

Unscrew the screw nut and remove the extrusion discs.

Leave it in a well-ventilated place for approximately 2 hours to dry.

After the dough is dry, gently tap the disc. Clean the disc using a mix of water and a mild detergent.

Wipe the disc with a clean, dry cloth.

Place the extrusion disc in the storage.

Note: It may be easier to allow any dough left on the parts to completely dry before cleaning. Leave parts in a well-ventilated area or refrigerator for approximately 2 hours. Use the scraper to remove the dried dough.

This product comes with 7 different extrusion discs and a ravioli mould allowing you to make a variety of different pastas. Additional ingredients like eggs and vegetable juice can also be added to make different flavoured varieties.

Use the flour cup to scoop a heaped cup of flour. Use the included scraper to scrape off the excess flour. This measurement is exactly 1 cup of flour (160g).

Press the “Manual” button. The machine will begin extruding the remaining dough.

Possible Cause: The outlet is turned off or the plug has poor contact.

Solution: Install power cord properly and turn on the outlet.

Possible Cause: Mixture is too dry.

Solution: Remove the dough from the mixing bowl, tear it into small peanut sized pieces. Add the correct amount of flour and press the manual button.

Possible Cause: Mixture is too wet.

Solution: Remove the extruding discs and replace it with a clean disc. Add the correct amount of water and press the manual button.

Possible Cause: Sometimes the mixing axle cannot reach the doughs at the bottom. It is normal to have some residual dough.

Solution: Stop the machine and use chopsticks to add the dough directly to the mixing axle. Press the Manual button and the pasta maker will continue to make noodles.

Possible Cause: The noodles will usually have more burrs or cracks at the beginning and at the end of the extruding process.

Solution: Add eggs or small amount of cooking oil, noodles to help make the pasta smoother. You can also tear the pasta into peanut sized pieces and put them back to mixing bowl. Then press the manual button function. The more you repeat this process, the pasta will be smoother and chewier.

Possible Cause: Mixture is too dry.

Solution: Add water following the ratios outlined in the “Operation” section and press the manual button.

Solution: After pasta comes out, lightly dust with flour. Cut noodles into proper length.

Possible Cause: Mixture is too dry.

Solution: Add water following the ratios outlined in the “Operation” section and press the manual button.

Possible Cause: Foreign object in machine.

Solution: Disassemble and clean the removable parts. Checking for any foreign objects. Reconnect the power, if it still displays “E1”, please contact help.Kogan.com for support.