JURA S80 (01) PDF MANUAL

Never use a machine which is damaged or has a defective mains cable.

In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from the mains supply.

If the mains cable of this machine is damaged it must be replaced with a special mains cable, which is available directly from JURA or from authorised JURA service centres.

Make sure that the S8/S80 and the mains cable are not located close to hot surfaces.

Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges.

Never open and repair the machine yourself. Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.

To completely and safely disconnect the machine from the power supply, first switch off the S8/S80 using the On/Off button. Only then should you remove the mains plug from the power socket.

Connect the S8/S80 directly to a domestic power socket. Using multi-socket adapters or extension cords may cause overheating.

Place the machine out of the reach of children.

Do not touch any hot parts. Use the handles provided.

Be careful to ensure that the milk system is correctly installed and clean. If incorrectly fitted or if it becomes blocked, the milk system or its parts might come off. There is a danger of parts being swallowed.

Never allow the mains cable to loosely hang down. The mains cable could pose a tripping hazard or become damaged.

Protect the S8/S80 from environmental influences such as rain, frost and direct sunlight.

Do not immerse the S8/S80, mains cable or connections in water.

Do not put the S8/S80 or any individual parts in the dishwasher.

Before cleaning, switch the S8/S80 off with the On/Off button. Always wipe the S8/S80 with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash.

Do not use alkaline cleaning agents when cleaning, use a soft cloth and a mild detergent.

Do not use any coffee beans treated with additives or caramelised coffee beans. Only use roasted, untreated coffee beans.

Only fill the water tank with fresh, cold water. Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

Switch the machine off with the On/Off button if you are going to be absent for a longer period of time and remove the mains plug from the power socket.

Children may not clean or service the machine unless supervised by a responsible person.

Do not allow children to play with the machine.

Keep children under the age of 8 away from the machine, or supervise them constantly.

Children aged 8 and over may only operate the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.

People, including children, who do not have the physical, sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

Filter cartridges should be kept out of the reach of children.

Store filter cartridges in a dry place in the sealed packaging.

Protect cartridges from heat and direct sunlight.

Do not use damaged filter cartridges.

Do not open filter cartridges.

You can operate the touchscreen display in two ways:

Touch: Touch the display with your finger, for example to start coffee preparation or undertake various settings in programming mode.

Slide: Move your finger across the display from left to right or from top to bottom (or vice versa). For example, you can select one of the speciality coffees in the product selector view or switch between programme items in programming mode.

Place the S8/S80 on a horizontal surface that is not sensitive to water.

Choose a spot for your S8/S80 which protects the machine against overheating. Ensure that the ventilation slots are not covered.

Only use roasted, untreated coffee beans to fill the bean container. Coffee beans which have been treated with additives (e.g. sugar), ground coffee or freeze-dried coffee will damage the grinder.

Remove the aroma preservation cover.

Remove any dirt or foreign objects from inside the bean container.

Fill the bean container with coffee beans and close the aroma preservation cover.

Hold the test strip briefly (for 1 second) under flowing water.

Shake off the water.

Wait for about 1 minute.

You will then be able to read the degree of water hardness from the discolouration of the Aquadur® test strip and the description on the packaging.

Precondition: The bean container has been filled.

Connect the mains cable to the machine.

Insert the mains plug into a power socket.

Press the On/Off button to switch the S8/S80 on.

Touch ‘Save’ after selecting the language.

Move your finger across the display to change the water hardness setting.

Touch ‘Save’.

Place one receptacle under the coffee spout and another under the fine foam frother.

Remove the water tank and rinse it with cold water.

Fit the filter cartridge extension supplied on top of the CLARIS filter cartridge Smart.

Insert the filter cartridge with its extension into the water tank.

Turn the filter cartridge clockwise until it audibly clicks into place.

Fill the water tank with fresh, cold water and reinsert the tank.

Empty the drip tray and put it back into the machine.

Place a receptacle under the coffee spout.

Remove the protective cover from the milk system.

Connect the milk pipe to the milk system.

Connect the other end of the milk pipe to a milk container or a milk cooler.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Connect accessory’ is displayed in the centre.

Touch ‘Connect accessory’.

Now follow the instructions on the display to connect the accessory to the S8/S80.

During the grinding operation you can change the coffee strength of single products. To do this, move your finger across the display.

During preparation you can change the preset amounts (e.g. amount of water or milk foam). To do this, move your finger across the display.

You can stop preparation at any time. To do this, touch ‘Cancel’.

Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming the cups. The full coffee aroma can develop only in prewarmed cups.

You can make permanent settings for all products in programming mode (Adjusting the product settings).

Preparation using the start screen: Simply touch the desired product. The following products are displayed as standard on the start screen:

• ‘Espresso’

• ‘Coffee’

• ‘2 x Coffee’

• ‘Hot water’

• ‘Cappuccino’

• ‘Latte macchiato’

• ‘Flat White’

• ‘Milk foam’

Preparation using the product selector view: Only some of the products you can prepare are shown on the start screen. As soon as you touch the product selector symbol in the top right, more products are displayed in a product selector view. The following additional products are shown in the product selector view:

• ‘Milk’

• ‘Caffè latte’

• ‘Hot water for green tea’

• ‘2 x Ristretto’

• ‘2 x Espresso’

• ‘Ristretto’

• ‘Macchiato’

Precondition: The start screen is displayed.

Place a cup under the coffee spout.

Touch ‘Coffee’.

Preparation starts. The preset amount of water for coffee flows into the cup.

Preparation stops automatically. The start screen is displayed. Your S8/S80 is ready for use.

Precondition: The start screen is displayed.

Place two cups under the coffee spout.

Touch the product selector symbol (top right) to go to the product selector view.

Move your finger across the display until ‘2 x Ristretto’ is displayed in the centre.

Touch ‘2 x Ristretto’ to start preparation.

Preparation starts. The preset amount of water for coffee flows into the cups. Preparation stops automatically. Your S8/S80 is once more ready for use.

Precondition: The start screen is displayed. Milk is connected to the fine foam frother.

Place a glass under the fine foam frother.

Set the selector switch for the professional fine foam frother to the Milk Foam position.

Touch ‘Latte macchiato’.

The preset amount of milk foam flows into the glass.

There is a short interval while the hot milk separates from the milk foam. This allows the typical layers of a latte macchiato to form.

Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically. Your S8/S80 is once more ready for use.

Precondition: The start screen is displayed. Milk is connected to the milk system.

Place a cup under the fine foam frother.

Set the selector switch for the professional fine foam frother to the Milk position. If you wish to prepare milk foam, set the selector switch to the Milk Foam position (selector switch in vertical position).

Touch ‘Milk foam’.

The milk foam is prepared. The preset amount of milk flows into the cup.

Preparation stops automatically. Your S8/S80 is once more ready for use.

Use ground coffee which is not ground too finely. Very fine coffee can block up the system so that the coffee only comes out in drips.

Never add more than two level measuring spoons of ground coffee.

If you did not fill the machine with a sufficient amount of ground coffee, ‘Not enough ground coffee’ is displayed and the S8/S80 stops the operation.

The desired speciality coffee must be prepared within approximately one minute after filling with the ground coffee. Otherwise the S8/S80 stops the operation and is once more ready for use.

Precondition: The start screen is displayed.

Place an espresso cup under the coffee spout.

Open the cover of the filler funnel for ground coffee.

Place one level measuring spoon of ground coffee into the filler funnel.

Close the cover of the filler funnel.

Touch ‘Espresso’. Preparation starts. ‘Espresso’ appears and the preset amount of water for espresso flows into the cup.

Preparation stops automatically. Your S8/S80 is once more ready for use.

Only adjust the consistency of grind when the grinder is running. If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.

The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

Precondition: The start screen is displayed.

Place a cup under the coffee spout.

Open the cover of the grinder adjustment switch.

Touch ‘Espresso’ to start preparation.

Turn the grinder adjustment switch to the desired position while the grinder is running.

The preset amount of water flows into the cup. Preparation stops automatically.

There is a danger of scalding from hot water splashes. Avoid direct contact with the skin.

Precondition: The start screen is displayed.

Touch the product selector symbol (top right) to go to the product selector view.

Move your finger across the display until ‘Hot water for green tea’ is displayed in the centre.

Touch ‘Hot water for green tea’.

Remove the professional fine foam frother from the milk system.

Fit the hot-water nozzle on the milk system.

Touch ‘Next’.

The preset amount of water flows into the cup.

Preparation stops automatically. Your S8/S80 is once more ready for use.

Open the water tank cover.

Remove the water tank and rinse it with cold water.

Fill the water tank with fresh, cold water and reinsert the tank.

Close the water tank cover.

Place a receptacle under the coffee spout.

Press the On/Off button to switch the S8/S80 on.

The machine will display ‘Welcome to JURA’, ‘Machine is heating’, and ‘Machine is rinsing’. The rinse stops automatically. Your S8/S80 is ready for use.

Pull out the drip tray.

Empty the coffee grounds container and the drip tray. Rinse them both with warm water. Always empty the coffee grounds container when the machine is switched on. This is the only way of resetting the coffee grounds counter.

Refit the coffee grounds container and the drip tray.

Rinse the water tank with clean water.

Clean the milk system (see ‘How to clean the milk system?’).

Remove the milk pipe and rinse it thoroughly under running water.

Dismantle and rinse the milk system (see ‘How to dismantle and rinse the professional fine foam frother?’).

Wipe the surface of the machine with a clean, soft, damp cloth (e.g. microfibre cloth).

In the interests of hygiene, we recommend changing the milk pipe and interchangeable milk spout on a regular basis (approximately every 3 months). Replacements are available from specialised dealers.

Clean the inside of the water tank, e.g. with a brush. Further information about the water tank is provided in these instructions for use (see ‘How to descale the water tank?’).

Traces of milk and coffee may stick to the top and bottom of the cup grille. If this happens, clean the cup grille.

When the S8/S80 is switched off, the system is automatically rinsed if a speciality coffee has been prepared. If milk has been prepared, you will also be prompted to clean the milk system.

Place one receptacle under the coffee spout and another under the milk system.

Press the On/Off button.

If milk has been prepared, you will be prompted to clean the milk system (‘Clean the milk system’). After 10 seconds the switch-off process continues automatically.

If milk has been prepared but you have not started milk system cleaning, the milk system is rinsed first (‘Milk system is being rinsed’).

The machine will display ‘Machine is rinsing’, and the system rinses itself. The operation stops automatically. Your S8/S80 is switched off.

Touch a product on the start screen for about 2 seconds to view the list of setting options:

• ‘Product settings’: Specify individual settings such as coffee strength, amount of water, etc.

• ‘Product name’: Change the name of the product.

• ‘Delete’: Remove a product from the start screen.

• ‘Replace product’: Replace the products on the start screen with your favourites.

• ‘Copy product’: Duplicate any product, for example to create a variant with a new product name and individual settings.

• ‘Double product’ (not for products with milk or hot water): Create a double product of the desired speciality.

You can only change the settings of products that are stored on the start screen.

For Ristretto and Espresso (10 levels of Coffee strength, Coffee: 15 ml – 80 ml): Temperature (low, normal, high), product name, delete/replace/copy/double product.

For Coffee (10 levels of Coffee strength, Coffee: 25 ml – 240 ml): Temperature (low, normal, high), product name, delete/replace/copy/double product.

For Two ristretti, two espressi, and two coffees (the amount set for the single product is doubled): Temperature (as for single product), product name, delete product.

For Cappuccino, flat white, and caffè latte (10 levels of Coffee strength, Coffee: 25 ml – 240 ml, Milk: 1 sec. – 120 sec.): Temperature (low, normal, high), product name, delete/replace/copy product.

For Latte macchiato (10 levels of Coffee strength, Coffee: 25 ml – 240 ml, Milk: 1 sec. – 120 sec., Interval: 0 sec. – 60 sec.): Temperature (low, normal, high), product name, delete/replace/copy product.

For Espresso macchiato (10 levels of Coffee strength, Coffee: 15 ml – 80 ml, Milk: 1 sec. – 120 sec.): Temperature (low, normal, high), product name, delete/replace/copy product.

For Milk foam and milk (Milk: 1 sec. – 120 sec.): Product name, delete/replace/copy product.

For Hot water and hot water for green tea (Water: 25 ml – 450 ml): Temperature (low, normal, high), product name, delete/replace/copy product.

The S8/S80 can be set to automatically switch itself off after a preset time following the last action on the machine to cut down energy consumption. You can set the automatic switch-off to 15 minutes, 30 minutes or 1-9 hours.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Touch ‘Switch off after’.

Now move your finger to the left or right to change the switch-off time.

Touch ‘Save’.

Touch ‘Back’ the number of times needed to display the start screen again.

In the programme item ‘Machine settings’ | ‘Save energy’ you can set an energy-saving mode:

‘Save energy’ / ‘1’: Soon after the last preparation, the S8/S80 stops heating up. The ‘ESM’ symbol (Energy Save Mode, E.S.M.) is displayed. Before you can prepare a speciality coffee, speciality coffee with milk, or hot water, the machine must heat up.

‘Save energy’ / ‘0’: All speciality coffees, speciality coffees with milk and hot water can be prepared without having to wait.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Save energy’ is displayed in the centre.

Touch ‘Save energy’.

Now move your finger across the controller and set it to ‘0’.

Touch ‘Save’.

Touch ‘Back’ the number of times needed to display the start screen again.

You can define whether the operating instructions on how to use the professional fine foam frother and hot-water nozzle should be displayed during preparation.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Operating instructions’ is displayed in the centre.

Touch ‘Operating instructions’.

Now move your finger across the controller and set it to ‘0’.

Touch ‘Save’.

Touch ‘Back’ the number of times needed to display the start screen again.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Factory setting’ is displayed in the centre.

Touch ‘Factory setting’.

Touch ‘Yes’ to reset the machine to the factory settings.

Your S8/S80 is switched off.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Units’ is displayed in the centre.

Touch ‘Units’.

Now move your finger to the left or right to change the setting to ‘oz’.

Touch ‘Save’.

Touch ‘Back’ the number of times needed to display the start screen again.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Display’ is displayed in the centre.

Touch ‘Display’.

Now move your finger to the left or right to change the setting.

Touch ‘Save’.

The water hardness can be adjusted on a continuous scale between 1°dH and 30 °dH.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Water hardness’ is displayed in the centre.

Touch ‘Water hardness’.

Now move your finger to the left or right to change the setting.

Touch ‘Save’.

Touch ‘Back’ the number of times needed to display the start screen again.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Choose language’ is displayed in the centre.

Touch ‘Choose language’.

Move your finger across the display until the desired language, e.g. ‘Deutsch’, is displayed in the centre.

Touch ‘Save’.

Touch ‘Zurück’ the number of times needed to display the start screen again.

In the programme item ‘Machine settings’ you can view the following information:

• ‘Product counter’: Number of prepared coffee speciality coffees, speciality coffees with milk and hot water.

• ‘Maintenance counter’: Number of maintenance programmes performed (cleaning, descaling etc.).

• ‘Version’: Software version.

Precondition: The start screen is displayed.

Touch ‘P’.

Touch ‘Machine settings’.

Move your finger across the display until ‘Product counter’ is displayed in the centre.

Touch ‘Product counter’.

Touch ‘Next’ to view the number of other products.

Touch ‘Back’ the number of times needed to display the start screen again.

Precondition: The start screen is displayed.

Place one receptacle under the coffee spout and another under the fine foam frother.

Touch ‘P’.

Move your finger across the display until ‘Maintenance status’ is displayed in the centre.

Touch ‘Maintenance status’.

Move your finger across the display until ‘Rinse’ is displayed in the centre.

Touch ‘Rinse’ to start the rinse operation.

The machine will display ‘Machine is rinsing’ and ‘Milk system is being rinsed’. The rinse stops automatically. The start screen is displayed.

15 minutes after milk preparation, the milk system is automatically rinsed. Therefore always place a receptacle under the milk system after preparing milk. To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water. Use only original JURA maintenance products. To clean the milk system, use the container supplied.

Precondition: The start screen is displayed. ‘Clean the milk system’ is displayed.

Touch ‘Clean the milk system’.

Touch ‘Clean the milk system’ again.

Touch ‘Start’.

Touch ‘Start’ again.

Remove the milk pipe from the milk container or milk cooler.

Add 1 dosing unit of milk system cleaner to the front part of the container.

Then fill with warm water up to the upper mark.

Place the container under the fine foam frother.

Connect the milk pipe to the container. To connect the milk pipe to the container correctly, the pipe must be fitted with a connector.

Touch ‘Next’.

The machine will display ‘Milk system is being cleaned’. The operation is interrupted, ‘Fresh water’.

Rinse the container thoroughly and fill the front part with fresh water up to the upper mark.

Place this under the fine foam frother and reconnect the milk pipe to the container.

Touch ‘Next’.

The machine will display ‘Milk system is being cleaned’. The operation stops automatically.

Remove the milk pipe and rinse it thoroughly under running water.

Remove the professional fine foam frother.

Dismantle the fine foam frother into its individual parts.

Rinse all the parts under running water. If there are severely dried-on milk residues, firstly immerse the individual parts in a solution of 250 ml warm water and 1 dosing unit of milk system cleaner. Then rinse the parts thoroughly.

Re-assemble the professional fine foam frother. Ensure that all individual parts are correctly and firmly connected to ensure optimum operation of the professional fine foam frother.

Re-fit the fine foam frother on the milk system.

Precondition: The start screen is displayed.

Remove and empty the water tank.

Fit the filter cartridge extension supplied on top of a CLARIS Smart filter cartridge.

Insert the filter cartridge with its extension into the water tank.

Turn the filter cartridge clockwise until it audibly clicks into place.

Fill the water tank with fresh, cold water and reinsert the tank.

The machine automatically detects that you have just inserted the filter cartridge.

The machine will display ‘Saved’ briefly on the display, then ‘Filter is being rinsed’, and water flows directly into the drip tray. Rinsing of the filter stops automatically.

The machine will display ‘Empty drip tray’.

Empty the drip tray and coffee grounds container and put them back into the machine.

The start screen is displayed.

Once the filter cartridge stops working (depending on the water hardness setting), the S8/S80 will prompt you to change the filter.

Precondition: The start screen is displayed. ‘Change the filter’ is displayed.

Touch ‘Change the filter’.

Touch ‘Change the filter’ again.

Remove and empty the water tank.

Turn the filter cartridge anticlockwise and remove it along with the extension from the water tank.

Fit the filter cartridge extension on top of a new CLARIS Smart filter cartridge.

Insert the filter cartridge with its extension into the water tank.

Turn the filter cartridge clockwise until it audibly clicks into place.

Fill the water tank with fresh, cold water and reinsert the tank.

The machine will display ‘Saved’ briefly on the display, then ‘Filter is being rinsed’, and water flows directly into the drip tray. Rinsing of the filter stops automatically.

The machine will display ‘Empty drip tray’.

Empty the drip tray and coffee grounds container and put them back into the machine.

The start screen is displayed.

After 180 preparations or 80 switch-on rinses, the S8/S80 will prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water. Use only original JURA maintenance products. Do not interrupt the cleaning programme. The quality of cleaning will be impaired if you do so.

Precondition: The start screen is displayed. ‘Clean machine’ is displayed.

Touch ‘Clean machine’.

Touch ‘Clean’.

Touch ‘Start’.

Touch ‘Start’ again.

The machine will display ‘Empty coffee grounds container’.

Empty the drip tray and coffee grounds container and put them back into the machine.

Place one receptacle under the coffee spout and another under the fine foam frother.

Touch ‘Next’.

The machine will display ‘Machine is being cleaned’ and water flows out of the coffee spout and the fine foam frother. The operation is interrupted, ‘Add cleaning tablet’.

Open the cover of the filler funnel for ground coffee.

Insert a JURA cleaning tablet into the filler funnel.

Close the cover of the filler funnel.

Touch ‘Next’.

The machine will display ‘Machine is being cleaned’, water flows repeatedly out of the coffee spout and the fine foam frother. The operation stops automatically.

The machine will display ‘Empty coffee grounds container’. Empty the drip tray and coffee grounds container and put them back into the machine.

Cleaning is now complete. The start screen is displayed.

The S8/S80 builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

If you are using a CLARIS Smart filter cartridge, you will not be prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this can cause irritation. Avoid contact with the skin or eyes. Rinse off the descaling agent with clean water. Should you get any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water. Use only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to the machine. Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. Clean up any splashes immediately.

The descaling programme lasts approximately 45 minutes.

Precondition: The start screen is displayed. ‘Decalcify machine’ is displayed.

Touch ‘Decalcify machine’.

Touch ‘Descale’.

Touch ‘Start’.

Touch ‘Start’ again.

The machine will display ‘Empty drip tray’. Empty the drip tray and coffee grounds container and put them back into the machine.

The machine will display ‘Pour descaling agent into water tank’. Remove and empty the water tank.

Completely dissolve 3 JURA descaling tablets in a receptacle holding 500 ml of water. This may take several minutes.

Pour the solution into the empty water tank and insert it into the machine.

Place one receptacle under the coffee spout and another under the fine foam frother.

Touch ‘Next’.

The machine will display ‘Machine is being descaled’ and water flows out of the fine foam frother repeatedly. The operation is interrupted, ‘Empty drip tray’. Empty the drip tray and coffee grounds container and put them back into the machine.

The machine will display ‘Fill water tank’. Remove the water tank and rinse it thoroughly.

Fill the water tank with fresh, cold water and reinsert the tank.

Place one receptacle under the coffee spout and another under the fine foam frother.

Touch ‘Next’.

The machine will display ‘Machine is being descaled’, the descaling operation is continued. The operation is interrupted, ‘Empty drip tray’. Empty the drip tray and coffee grounds container and put them back into the machine.

Descaling is now complete. The start screen is displayed.

If the descaling operation stops unexpectedly, rinse the water tank thoroughly.

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time.

Precondition: ‘Fill bean container’ is displayed.

Switch the machine off with the On/Off button.

Remove the aroma preservation cover.

Clean the bean container with a soft, dry cloth.

Fill the bean container with coffee beans and close the aroma preservation cover.

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

Remove the water tank.

If you use a CLARIS Smart filter cartridge, remove this.

Completely fill the water tank and dissolve 3 JURA descaling tablets in it.

Leave the water tank with the descaling solution for several hours (e.g. overnight).

Empty the water tank and rinse it thoroughly.

If you use a CLARIS Smart filter cartridge, insert this again.

Fill the water tank with fresh, cold water and reinsert the tank.

Cause/Result: The water tank is empty. You cannot prepare any products.

Action: Fill the water tank (see ‘How to fill the water tank?’).

Cause/Result: The coffee grounds container is full. You cannot prepare any products.

Action: Empty the coffee grounds container and the drip tray (see ‘What daily maintenance is required for the S8/S80?’).

Cause/Result: The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any products.

Action: Fit the drip tray.

Cause/Result: The bean container is empty. You cannot prepare any speciality coffees, but you can prepare hot water and milk.

Action: Fill the bean container (see ‘How to fill the bean container?’).

Cause/Result: The filter cartridge no longer works.

Action: Replace the CLARIS Smart filter cartridge (see ‘How to change the CLARIS Smart filter cartridge?’).

Cause/Result: The S8/S80 is prompting you to clean it.

Action: Perform cleaning (see ‘How to clean the S8/S80 machine?’).

Cause/Result: The S8/S80 is prompting you to descale it.

Action: Perform descaling (see ‘How to descale the S8/S80 machine?’).

Cause/Result: The system is too hot to start a maintenance programme.

Action: Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water.

Cause/Result: The fine foam frother is dirty.

Action: Clean the fine foam frother (see ‘How to clean the milk system?’).

Dismantle and rinse the fine foam frother (see ‘How to dismantle and rinse the professional fine foam frother?’).

Cause/Result: The coffee is ground too finely and obstructs the system. The water hardness may not have been correctly set.

Action: Set the grinder to a coarser setting (see ‘How to adjust the grinder’s consistency?’).

Perform descaling (see ‘How to descale the S8/S80 machine?’).

Cause/Result: The beans used are resulting in an above-average volume of ground coffee.

Action: Reduce the coffee strength or choose a finer grinder setting (see ‘How to adjust the grinder’s consistency?’).

Cause/Result: The water tank float is trapped.

Action: Descale the water tank (see ‘How to descale the water tank?’).

Cause/Result: There are foreign objects in the grinder.

Action: Contact customer support in your country.

Cause/Result: If the machine has been exposed to the cold for a long period of time, heating may be disabled for safety reasons.

Action: Warm the machine at room temperature.

Action: Switch the S8/S80 off with the On/Off button. Contact customer support in your country.

Precondition: The start screen is displayed.

Remove the milk pipe from the fine foam frother.

Place a receptacle under the fine foam frother.

Touch ‘Milk foam’.

Remove and empty the water tank.

Change the time to ’60 sec.’.

Steam will continue to be discharged from the fine foam frother until the system is empty.

The machine will display ‘Fill water tank’.

Press the On/Off button.

Your S8/S80 is switched off.