JURA IMPRESSA F90 (01) PDF MANUAL

JURA IMPRESSA F90 (01) PDF SUMMARY:

How do I check the mains voltage?

The coffee machine is preset in the factory to the correct mains voltage. Check if your local mains supply voltage complies with the information given on the type plate on the underside of the coffee machine.

---

How do I check the electrical fuse?

The coffee machine is designed for an electric current of 10 Ampères. Check if the electrical fuse has sufficient capacity.

---

What kind of water should I use to refill?

Only use fresh, cold water. Never fill in milk, mineral water or other liquids.

---

How do I refill the water?

• Take out the water tank and thoroughly rinse it with cold tap water.
• Then fill the water tank and re-install it in the coffee machine. Make sure the tank is installed correctly and that it engages properly.

---

How do I fill the bean tank?

To ensure that your machine will work perfectly for a long time and to avoid damage, please note that the grinding gear of your JURA coffee machine is not suitable for coffee beans which were treated, during or after roasting, with additives (e.g. sugar). Such coffee blends may damage the grinding gear. Any repair costs resulting from the use of such blends are not covered by warranty.

• Open the cover of the bean tank.
• Remove any dirt or foreign matter from the bean tank.
• Fill coffee beans in the bean tank and close the cover.

---

How do I adjust the grinding gear?

You can adjust the grinding gear to the roast of your coffee. It is recommended that you use:

• a fine adjustment (the smaller the dots, the finer the grinding is) for a light roast
• a coarse adjustment (the bigger the dots, the coarser the grinding is) for a dark roast

The grinding degree may only be adjusted while the grinding gear is running.

• Open the cover of the bean tank.
• To adjust the grinding degree turn the rotary switch to the required position.

---

How do I use the cup illumination?

The cup illumination puts your coffee in a good light, making it a treat for the eyes. When you plug in or switch on the machine or press any key, the cup illumination is activated for 1 minute. To switch on the cup illumination, with the machine switched off, press any key.

---

How do I adjust the water hardness?

Before using the machine for the first time the hardness of the water used must be adjusted. Use the supplied test sticks for this.

1° German hardness is equivalent to 1.79° French hardness.

The coffee machine has 5 hardness degrees which can be used and are displayed while you are adjusting the water hardness.

The displayed information means the following:

• WATER HARDNESS –– Water hardness function switched off
• WATER HARDNESS 1 German water hardness degree 1 to 7° French Water hardness degree 1.79 – 12.53°
• WATER HARDNESS 2 German water hardness degree 8 to 15° French Water hardness degree 14.32 – 26.85°
• WATER HARDNESS 3 German water hardness degree 16 to 23° French Water hardness degree 28.64 – 41.14°
• WATER HARDNESS 4 German water hardness degree 24 to 30° French Water hardness degree 42.96 – 53.7°

When the machine leaves the factory it is adjusted to WATER HARDNESS 3. You can adjust another hardness. To do this, proceed as follows: Pull out the mains cable from the cable box on the rear side of the coffee machine and connect the machine to mains supply.

• Press the key to switch on the coffee machine.
• Your coffee machine is switched to start-up position.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: WATER HARDNESS 3.
• Press symbol, you will hear an acoustic signal and the hardness degree flashes.
• Now, press symbols to adjust the required hardness degree.
• Press symbol to confirm the new settings.
• Press programming key to leave Programming Mode.

---

How do I install the filter?

• Use the key to switch on the coffee machine.
• Fold up the cartridge holder. Insert the filter cartridge in the water tank.
• Close the cartridge holder until it engages audibly.
• Fill the water tank with cold, fresh tap water and install it again.
• Press Programming key until you hear an acoustic signal.
• Press symbol , NO flashes on the display.
• Press symbol until the following message is displayed: FILTER YES (YES flashes).
• Press symbol.
• INSTALL FILTER / WATER PORTION
• Turn the selector switch of the Professional Cappuccino Frother to the steam position.
• Place a sufficiently large receptacle (at least 0.5 litre) under the Professional Cappuccino Frother and press the water portion draw-off key.
• FILTER RINSING. The water draw-off operation is stopped automatically.

Now you have activated the filter. In Programming Mode the water hardness selection function is no longer displayed.

---

How do I replace the filter?

After 50 litres of water the filter cartridge will need to be replaced. The display will prompt you to change the filter. Please monitor the period of use of the CLARIS plus filter cartridge (max. 2 months) using the scale on the cartridge holder by the water tank.

• Use the key to switch off the coffee machine.
• Press maintenance key for some seconds, with the machine switched off.
• INSTALL FILTER / WATER PORTION
• Fold up the cartridge holder. Insert the filter cartridge in the water tank.
• Close the cartridge holder until it engages audibly.
• Fill the water tank with cold, fresh tap water and reinstall it in the coffee machine.
• Turn the selector switch of the Professional Cappuccino Frother to the steam position.
• Place a sufficiently large receptacle (at least 0.5 litre) under the Professional Cappuccino Frother and press the draw-off key.
• FILTER RINSING. The water draw-off operation is stopped automatically.

---

How do I rinse the coffee machine?

When the coffee machine was switched off and has cooled down in the meantime, a rinsing operation is started when the machine is switched on again. When the machine is switched off, a rinsing operation is started automatically.

---

How do I draw off coffee?

You can change the selected product at any time by pressing the symbols before starting the operation. The selected product is displayed.

• Use the key to switch on the coffee machine.
• Place 1 cup under the adjustable coffee spout and press symbol.
• Press symbols ( / / ) to select the strength of your coffee.
• Press symbol.

---

How do I draw off espresso?

• Use the key to switch on the coffee machine.
• Place 1 cup under the adjustable coffee spout and press symbol.
• Press ( / / ) to select the strength of your espresso.
• Press symbol.

---

How do I draw off a large cup of coffee?

• Use the key to switch on the coffee machine.
• Place 1 cup under the adjustable coffee spout and press symbol.
• Press ( / / ) to select the strength of your coffee.
• Press symbol.

---

How do I draw off pre-ground coffee?

Never use instant coffee or quick-coffee. It is recommended that you always use powder from fresh coffee beans or, pre-ground, vacuum-packed coffee. Never fill in more than 2 portions of powder. The pre-ground coffee tank is no storage tank. Make sure that the pre-ground you use is not too fine. This may cause blocking of the system. In this case the coffee only drips out of the coffee spout.

If you press the draw-off key unintentionally, you can stop the operation by pressing the maintenance key. Your coffee machine will carry out a rinsing operation.

• Use the key to switch on the coffee machine.
• Press selection key.
• Now fill in 1 or 2 level dosing spoonfuls of pre-ground coffee in the filler funnel for pre-ground coffee.
• Place 1 cup under the adjustable coffee spout and press the corresponding symbol ( / / ).
• Press symbol.

---

How do I draw off hot water?

You can adjust the water portion individually. Install the hot water jet to obtain perfect water flow.

At the start of the water draw-off there can be splashing Avoid direct contact with the skin! Do not replace the replaceable hot water jet directly after drawing off water, because the jet is hot after the draw-off operation.

---

How do I dispense Cappuccino with the Professional Cappuccino Frother?

Cappuccino comprises one third each of Espresso, hot milk and milk foam. You produce the milk portion with the Professional Cappuccino Frother. When steam is drawn, a vacuum is produced which, with the aid of the Professional Cappuccino Frother, draws in the milk and produces milk foam.

To ensure perfect function, the Professional Cappuccino Frother must be cleaned regularly.

Make sure that the nozzle is correctly fitted. If the nozzle becomes blocked with particles of milk residue or is incorrectly assembled, a danger can arise during use whereby the nozzle may jump off.

• When using for the first time, remove the protective cover from the Professional Cappuccino Frother.
• Remove the milk pipe from the Welcome Pack and connect it to the Professional Cappuccino Frother.
• Insert the other end of the milk pipe into a Tetra Pak of milk or connect it to a milk container.
• Place a cup under the Professional Cappuccino Frother.
• Place a cup under the hot water jet.
• Press water draw-off key.

---

How do I dispense hot milk with the Professional Cappuccino Frother?

Turn the selector switch of the Professional Cappuccino Frother to the milk range. The procedure for dispensing hot milk is the same as the procedure for dispensing milk foam for Cappuccino.

---

How do I rinse the Professional Cappuccino Frother?

• Carefully pull off the Professional Cappuccino Frother from your IMPRESSA.
• Dismantle the Professional Cappuccino Frother into its individual parts.
• Thoroughly rinse all parts of the nozzle under running water.
• Reassemble the Professional Cappuccino Frother and refit it on to your IMPRESSA.

---

How do I clean the Professional Cappuccino Frother?

To ensure that the Professional Cappuccino Frother functions perfectly, you should clean it daily if you have pre-pared milk foam or hot milk.

You can obtain the JURA Auto-Cappuccino Cleaner from the specialist shop.

• Place a receptacle under the Professional Cappuccino Frother.
• Fill a second receptacle with 2.5 dl of fresh water and add one capful of the Auto-Cappuccino Cleaner.
• Dip the milk pipe into the second receptacle with the Auto-Cappuccino Cleaner.
• Turn the selector switch of the Professional Cappuccino Frother to the milk position or to the milk foam position.
• Press the steam portion draw off key.
• Draw steam until the receptacle with the Auto-Cappuccino Cleaner is empty. This procedure cleans the Professional Cappuccino Frother and the milk pipe.
• Fill the receptacle with 2.5 dl of fresh water. Dip the milk pipe into the receptacle with the fresh water.
• Press steam portion draw-off key.
• Draw steam until the receptacle with the fresh water is empty. This procedure rinses the Professional Cappuccino Frother and the milk pipe with fresh water.

Cleaning of the Professional Cappuccino Frother is now complete, your IMPRESSA is ready for use.

---

How do I switch off the coffee machine?

To ensure perfect operation, please switch your IMPRESSA to standby mode with the symbol first. Then switch the machine off with the power switch.

---

How do I program the filter?

Refer to the section on Inserting the filter.

---

How do I program the water hardness?

Refer to the section on Adjusting the water hardness.

---

How do I program the aroma INTENSIVE or STANDARD?

The aroma for the powder quantities ( / / ) was adjusted to Intensive in the factory. If requested it can also be set to Standard.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Touch symbol until the following message is displayed: AROMA INTENSIVE.
• Press symbol, you will hear an acoustic signal, INTENSIVE flashes.
• Use the symbols to adjust the aroma to STANDARD.
• Press symbol to confirm the new settings.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the temperature?

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Touch symbol until the following message is displayed: TEMP. HIGH.
• Press symbol, you will hear an acoustic signal and HIGH flashes.
• Use the symbol to adjust the temperature to NORMAL.
• Press symbol to confirm your settings.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the water quantity?

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: WATER QUANTITY.
• Press symbol.
• Select the product, the water quantity of which you want to programme ( / / )
• Press symbol, the value flashes.
• Use symbols to change the value in 5 ml increments.
• Press symbol to save the water quantity for this product.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program 1 cup?

Now, you will program the draw-off key 1 cup. This has no influence on the touch screen.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: 1 CUP 120 ML.
• Press symbol, the value flashes.
• Use symbols to change the value in 5 ml increments.
• Press symbol to save the water quantity for 1 cup.
• Press one of the symbols ( / / ) to select the strength of your coffee.
• Press symbol to save the new settings.
• Use the symbols to reach the next programming stage or press key to quit Programming Mode.

These settings were taken over for the draw-off key for 2 cups.

---

How do I program the steam portion?

The programmable steam portion time is between 3 and 60 seconds.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: STEAM 20 SEC.
• Press symbol, the value 20 flashes.
• Press symbols to change the value.
• Press symbol to save the new value.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the water portion?

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: WATER PORTION.
• Press symbol, you will hear an acoustic signal.
• Press water portion draw-off key.
• When the required water quantity is reached press key . The water draw-off operation is stopped, the water portion is programmed now.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the time?

You must programme the time if you want to use the automatic switch-on function.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: TIME —:—.
• Press symbol, you will hear an acoustic signal and —:— flashes.
• Use symbols to adjust the hours and confirm by pressing.
• Use symbols to adjust the minutes and confirm by pressing . The time is now programmed.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

If the machine is disconnected from mains supply, the time must be programmed again.

---

How do I program the automatic switch-on time?

You must programme the time if you want to use the automatic switch-on function.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: MACHINE ON —:—.
• Press symbol, you will hear an acoustic signal and —:— flashes.
• Use the symbols to select the hours and confirm by pressing.
• Use symbols to adjust the minutes and confirm by pressing . The switch-on time is now programmed.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the automatic switch-off time?

You can programme your coffee machine such that it will switch off automatically after a certain time. You can programme the switch-off time in a range between 0.5 and 9 hours, or select –:– (i.e. function switched off).

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: OFF AFTER 5.0 HOURS.
• Press symbol, you will hear an acoustic signal and 5.0 flashes.
• Use the symbols to select the hours and confirm by pressing.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I check the cup counter?

This function is available with the following products: In Aroma Select via symbols , , and via the pre-ground coffee draw-off key , draw-off key for 1 cup and draw-off key for 2 cups.

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: DRAW OFFS … (Total number of draw offs).
• To learn how often a function was selected, press the corresponding key or symbol.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I program the language?

• Use the key to switch on the coffee machine.
• Press programming key until you hear an acoustic signal.
• Press symbol until the following message is displayed: SPRACHE DEUTSCH.
• Press symbol, you will hear an acoustic signal and DEUTSCH flashes.
• Press symbols to select the required language.
• Press symbol to save the new settings.
• Use the symbols to reach the next programming stage or press programming key to quit Programming Mode.

---

How do I refill the water?

• If this information is displayed, drawing off products is no longer possible. Refill water as described in the PDF.

The water tank should be rinsed daily and refilled with fresh water. Only fill in fresh, cold water. Never fill in milk, mineral water or other liquids.

---

How do I empty the coffee grounds container?

• If this information is displayed, drawing off products is no longer possible and the coffee grounds container must be emptied.

Your coffee machine must be switched on.

Carefully take out the drip tray, it is filled with water.

The red water level warning message appears when the coffee drip tray is full.

---

What does “NO TRAY” mean?

• If this information is displayed, the drip tray is not installed properly or was not installed at all.

---

How do I fill the bean tank?

• We recommend that you clean the bean tank regularly before refilling beans, using a dry cloth. Before doing this, switch off the coffee machine.
• Refill beans as described in the PDF.

The message REFILL BEANS will disappear after you draw off your next cup of coffee.

---

How do I replace the filter?

After drawing off 50 liters the filter cartridge will be used up.

Refer to the PDF section on Replacing the filter.

---

How do I clean the coffee machine?

After 200 draw-off operations or after 160 rinsing operations, the coffee machine must be cleaned. A message appears on the display, telling you to start the cleaning programme. You can still draw off coffee or hot water/steam. However, it is recommended that you should clean the machine within the next few days.

---

What does “Coffee machine calcified” mean?

During normal use of the coffee lime scaling will occur. The degree of calcification depends on the hardness of the water you use. The machine will inform you when de-scaling is required. You can still draw off coffee or hot water/steam. However, it is recommended that you should de-scale the machine within the next few days.

---

What are some general cleaning instructions?

• Never use scrapers, abrasive cloths, sponges or caustic chemicals for cleaning.
• Clean the inside and outside of the case using a soft, moist cloth.
• Clean the 2-stage frothing jet each time it was used.
• Clean the control panel with a micro-fibre cloth.
• To ensure that the Professional Cappuccino Frother functions perfectly, you should rinse it with water each time after prepar-ing milk.
• To ensure that the Professional Cappuccino Frother functions perfectly, you should clean it daily if you have prepared milk.
• The water tank should be rinsed daily and refilled with fresh water.

If lime-scaling forms in the tank, remove it using a commercial de-scaling agent. Take out the water tank.

If you use a CLARIS plus filter cartridge, remove it before de-scaling the tank.

---

How do I empty the system?

This is necessary to protect the coffee machine against damage occurring during transport as a result of frost.

• Use the key to switch off the coffee machine.
• Place a receptacle under the Professional Cappuccino Frother.
• Turn the selector switch of the Professional Cappuccino Frother to the steam position.
• Press the steam portion draw-off key until the following message appears: SYSTEM EMPTYING.

The coffee machine is switched off.

---

How do I clean the machine?

The coffee machine features an integrated cleaning programme. The procedure takes some 15 minutes.

Original JURA cleaning tablets which are specially designed for the cleaning program of your IMPRESSA are available at your authorized dealer. Please note that machine defects or residues in the water cannot be excluded if you use inappro-priate cleaning agents.

Once started, the cleaning operation must not be interrupted.

After each cleaning operation the filler funnel for the 2nd coffee type should be cleaned.

• Press maintenance key until the following message appears: EMPTY TRAY. Take out the tray, empty it and re-install it.
• Press maintenance key.
• TABLET / PRESS MAINTENANCE . You will hear an acoustic signal.
• EMPTY TRAY. You will hear an acoustic signal.
• PRESS MAINTENANCE
• EMPTY TRAY. You will hear an acoustic signal.

Wipe coffee powder tank with a dry cloth after the cleaning program has finished.

Now the cleaning operation is complete.

---

How do I de-scale the machine?

The coffee machine features an integrated de-scaling programme. The procedure takes some 30 minutes.

Original JURA de-scaling tablets which are specially designed for the de-scaling program of your IMPRESSA are available at your authorized dealer. Please note that machine defects or residues in the water cannot be excluded if you use inappropriate de-scaling agents.

Your machine will inform you if it needs de-scaling. You can still draw off coffee or hot water / steam and start the de-scaling programme later.

Switch off the system before starting the de-scaling pro-gramme. Once started, the de-scaling programme must not be interrupted.

If acidic de-scaling agents are used, remove any splashes and drops from sensitive surfaces, in particular surfaces made of natural stone and wood, alternatively take appropriate pre-ventive measures.

In any case wait until the de-scaling agent is used up and the tank is empty. Never refill de-scaling agent.

• Use the key to switch off the coffee machine.
• Remove the Professional Cappuccino Frother.
• Take out the water tank.
• Press maintenance key until the following message appears: EMPTY TRAY
• Completely dissolve the content of one blister (3 tablets) in a jug containing 0.5 liters of water, and fill the mixture in the water tank. Reinstall the water tank.
• Place a sufficiently large receptacle under the hot water spout.
• PRESS MAINTENANCE / AGENT IN TANK

The de-scaling agent comes out of the hot water jet in intervals. After some intervals the de-scaling agent is discharged directly in the drip tray.

• EMPTY TRAY. You will hear an acoustic signal.
• Thoroughly rinse the water tank and fill it with fresh cold tap water. Then reinstall it.
• Place a sufficiently large receptacle under the hot water spout.
• PRESS MAINTENANCE / REFILL WATER

The water comes out of the hot water jet in intervals. After some intervals the water is discharged directly in the drip tray.

• EMPTY TRAY. You will hear an acoustic signal.
• PRESS MAINTENANCE

After the de-scaling, clean the aluminium front using a slightly moist cloth.

---

How do I adjust the coffee spout for the perfect coffee?

You can adjust the height of the coffee spout to the size of your cups.

---

How do I adjust the grinding degree for the perfect coffee?

Refer to the PDF section Adjusting the grinding gear.

---

How do I preheat cups for the perfect coffee?

You can preheat the cups using hot water or steam. The smaller the coffee you want to draw off, the more important preheating is.

---

What are some tips for adding sugar and cream to my coffee?

Stirring coffee/tea will result in heat being released. Adding refrigerated cream or milk will reduce the temperature of the coffee significantly.

---

What does “REFILL WATER” mean?

Water tank is empty. Refill water.

---

What if the float is defective?

Rinse or de-scale water tank.

---

What does “REFILL BEANS” mean?

Bean tank is empty. Refill beans.

---

What if I have refilled beans, but the message still appears?

Draw off a cup of coffee. The message will disappear only after you have drawn off a cup of coffee.

---

What does “EMPTY COFFEE GROUNDS CONTAINER” mean?

Coffee grounds container full. Empty coffee grounds container.

---

What if the tray is reinstalled too early after emptying?

Wait 10 sec. before reinstalling the tray.

---

What does “NO TRAY” mean?

Drip tray not installed properly or missing. Install tray properly.

---

What does “CLEAN MACHINE” mean?

Cleaning required. Start cleaning programme.

---

What does “MACHINE CALCIFIED” mean?

De-scaling required. Start de-scaling programme.

---

What does “REPLACE FILTER” mean?

Filter empty. Change filter.

---

What does “FAULT” mean?

General fault:

1. switch off
2. disconnect from mains supply
3. connect machine to mains supply
4. switch on machine
5. Have machine checked.

---

What to do if there is a very loud noise coming from the grinding gear?

Foreign body in grinding gear. Drawing off pre-ground coffee is still possible. Have machine checked.

---

What to do if there is too little foam when frothing the milk?

Professional Cappuccino Frother has become dirty. Clean the Professional Cappuccino Frother.

Individual parts of the Professional Cappuccino Frother are incorrectly assembled. Check correct assembly of the Professional Cappuccino Frother.

---

What to do if coffee only drips from the coffee spout?

Grinding degree too fine. Coarser grinding gear adjustment.

Pre-ground coffee too fine. Use a coarser pre-ground coffee.