IQOS 3 MULTI (01) PDF Document

Press and hold IQOS Multi Button for 4 seconds then release; Battery Status Light and Button & Status Light will flash.

Rotate the Lid counter-clockwise.

Insert and gently press the HeatStick to the line on filter.

Hold the Button until the IQOS 3 MULTI vibrates and the Button & Status Light pulses white.

Start using once the IQOS 3 MULTI vibrates twice and the Button & Status Light is solid white.

To signal the last 30 seconds, the IQOS 3 MULTI will vibrate twice and the Button & Status Light pulses white.

Slide the Cap upward and then remove the used HeatStick.

Slide the Cap upward and remove completely. Insert the IQOS Cleaning Tool and rotate gently. Clean daily for optimal experience.

Tap the IQOS Multi Button to check battery level.

Press and hold the IQOS Multi Button for 10 seconds then release; the Battery Status Light and Button & Status Light will fade in, blink twice, then progressively fade in to confirm a reset.

The IQOS 3 MULTI is outside operating temperature (<0°C/>50°C). Wait until the device is within temperature limits.

Reset the IQOS 3 MULTI. If blinking persists, please contact Customer Care.

IQOS 3 MULTI is powered with sealed Lithium-ion (Li-ion) batteries. Under normal conditions of use, the battery is sealed. If battery fluid leaks, follow these precautions:

• If you swallow fluid, seek medical attention immediately. Do not induce vomiting or ingest food or drink.

• If fluid is inhaled, get fresh air and seek medical attention.

• In case of contact with skin, wash hands and do not touch eyes.

• In case of contact with eyes, immediately flush with running water for at least 15 minutes and seek medical attention.

When using IQOS 3 MULTI under hot and humid weather conditions, the water in the aerosol make the aerosol temperature feel very hot. To help avoid this sensation, store your HeatSticks in a cool dry place. Do not expose product to high humidity conditions or direct sunlight. Do not use IQOS 3 MULTI during hot conditions or in periods of high humidity. If you experience discomfort, stop using the product and contact a health care professional.

IQOS 3 MULTI could cause an allergic reaction. Stop using IQOS 3 MULTI and seek medical attention immediately if you experience any of the following symptoms that may indicate a serious allergic reaction: swelling of the face, lips, tongue, gums, throat, or body, difficulty breathing, or wheezing.

IQOS 3 Multi – Model: A1405

Battery type: Li-ion rechargeable battery

Input: 5V 2A

Bluetooth 4.1

USB Type C Cable

IQOS AC Power Adaptor

Model: S52A21, S21A20, S21A22, S21A23, S21A25, S21A27

Input: 100V-240V~ 50/60HZ 0.3A

Output: 5V 2A

Batteries must not be removed by the consumer. At end of product life, only an authorized recycler may safely remove batteries by using the following steps for the IQOS 3 MULTI (A1405):

Step 1. Check the voltage: The device should be fully discharged before disassembling it.

Step 2. Rear housing removal (the use of a jig is recommended): Remove the housing hooks, which are located on the lower side of the device (on the side, close to the USB socket). The rear housing can now be removed.

Step 3. Sub-assembly removal: Enlarge both sides of the extruded chassis, then remove the core sub-assembly.

Step 4. Battery removal: Gently pull the battery away from the adhesive backing. Remove the screws which secure the PCB, then carefully remove the battery and PCB from the casing. Disconnect the battery cable by using the relevant tool (AVX 06-9296-7001-01-000).

Step 5. Disposal: Recycle the battery, assembly and PCB according to local regulations.