HEAT & GLO SL-550TRSI-AUE (01) PDF Document

The HEAT & GLO SL-550TRSI-AUE can be mounted on a flat surface with a minimum 6 mm base or on four corner supports, such as concrete masonry blocks, positioned to contact all four perimeter edges on the bottom of the unit.

The minimum clearances are: Glass Front: 914 mm; Floor: 0 mm; Rear: 13 mm; Sides: 13 mm; Top: 86 mm; Ceiling: 787 mm.

Vertical Sections: 25 mm. Horizontal Sections: Top 75 mm, Bottom 25 mm, Sides 25 mm. At Wall Firestops: Top 75 mm, Bottom 25 mm, Sides 25 mm.

The HEAT & GLO SL-550TRSI-AUE uses an electronic ignition system that operates on a 6 volt system.

For natural gas, the minimum inlet gas supply pressure is 1.13 kPa and the manifold outlet pressure should be set at 0.8 kPa.

For propane, the minimum inlet gas supply pressure is 2.75 kPa and the manifold outlet pressure should be set at 2.36 kPa.

No, you must not mix DVP-series and SLP-series components in any flue system configuration for the HEAT & GLO SL-550TRSI-AUE.

The maximum vertical flue length allowed for the HEAT & GLO SL-550TRSI-AUE is 10.97 meters.

A vertical flue restrictor must be installed if the HEAT & GLO SL-550TRSI-AUE installation requires a vertical flue exceeding 4.5 meters above the unit with no horizontal flue or elbows.

The maximum horizontal run for straight out flueing on the HEAT & GLO SL-550TRSI-AUE is 610 mm.

The gas supply line for the HEAT & GLO SL-550TRSI-AUE should be purged of any trapped air prior to the first firing of the unit.

To light the HEAT & GLO SL-550TRSI-AUE, simultaneously press the star and up arrow buttons on the remote control until a short acoustic signal confirms the start sequence has begun.

To turn off the gas to the HEAT & GLO SL-550TRSI-AUE, push the OFF button on the remote control and remove the batteries from the receiver.

The controls for the HEAT & GLO SL-550TRSI-AUE are located in the lower compartment behind the lower door. Access is gained by lifting the door up.

In the event of a power interruption during operation of the HEAT & GLO SL-550TRSI-AUE, either push the OFF button on the remote control or open the access door and manually push the switch to OFF. The switch must be returned to the ON position prior to operation once power is restored.

To properly clean the burner and pilot assembly of the HEAT & GLO SL-550TRSI-AUE, turn off the gas, remove the logs, and clean all foreign materials from the top of the burner and pilot. Check to make sure the burner orifice is clean and the pilot orifice is not plugged.

The glass door on the HEAT & GLO SL-550TRSI-AUE should be cleaned using a household glass cleaner. Do not handle or attempt to clean the glass when it is hot.

The receiver must learn a new code. Press and hold the receiver’s reset button until you hear 2 acoustic signals. After the second longer acoustic signal, release the reset button and within the subsequent 20 seconds, press the down arrow on the remote handset until you hear an additional long acoustic signal confirming the new code is set on your HEAT & GLO SL-550TRSI-AUE.

Glass sooting in the HEAT & GLO SL-550TRSI-AUE can be caused by flame impingement on logs, improper venturi setting, or debris around the venturi. To correct it, adjust the log set so the flame does not impinge on it, adjust the air shutter at the base of the burner, or inspect the opening at the base of the burner to ensure no material is placed there.

The burner injector size for the HEAT & GLO SL-550TRSI-AUE when using natural gas is 2.49 mm.

The burner injector size for the HEAT & GLO SL-550TRSI-AUE when using propane is 1.45 mm.

The maximum gas consumption of the HEAT & GLO SL-550TRSI-AUE for natural gas is 28.0 mJ/h.

The maximum gas consumption of the HEAT & GLO SL-550TRSI-AUE for propane is 26.0 mJ/h.

After the first few minutes of lighting the HEAT & GLO SL-550TRSI-AUE, moisture will disappear and within 15-30 minutes the flames should become yellow. Tips of the flames should never hit the top of the firebox.

Check if the manual override knob is in the MAN position, ensure the valve is not turned down to pilot flow, or check for low inlet pressure to the valve of the HEAT & GLO SL-550TRSI-AUE.

No, the HEAT & GLO SL-550TRSI-AUE is not for use with solid fuel.

To remove the glass door of the HEAT & GLO SL-550TRSI-AUE, release the four glass clips around the glass door and carefully lift the glass up and out away from the appliance.

To replace the glass door on the HEAT & GLO SL-550TRSI-AUE, place the bottom edge on top of the bottom mounting brackets, push the glass against the unit, and latch the two fasteners at the top and the two fasteners at the bottom.

Place log #1 onto the log grate of the HEAT & GLO SL-550TRSI-AUE so that the notches in the bottom of the log fit on the right three grate bars, then push it towards the rear locating tabs.

Place log #2 in the HEAT & GLO SL-550TRSI-AUE so that its left edge sits against the left front grate corner and its right edge rests against the tab on the second grate bar.

Position log #3 in the HEAT & GLO SL-550TRSI-AUE so that its right edge sits on log #1 and its left edge sits on the first grate bar behind log #2.

Position log #4 in the HEAT & GLO SL-550TRSI-AUE between log #1 and the locating tab on the fourth grate bar, pushing its left hand side back to the locating tab on the grate bar.

Put the forked end of log #5 on the base of the HEAT & GLO SL-550TRSI-AUE in front of the grate, towards the center of the second bar grate.

Place log #6 on the base in front of the grate of the HEAT & GLO SL-550TRSI-AUE as shown.

Place log #7 on the groove in log #2 of the HEAT & GLO SL-550TRSI-AUE, with its rear top on log #1 and front top resting on log #5.

Hook log #8 on the right hand corner grate bar of the HEAT & GLO SL-550TRSI-AUE and rest its rear on log #1.

Logs for the HEAT & GLO SL-550TRSI-AUE are fragile; remove them carefully from the packaging. The logs get very hot, so handle them only when cool.

Maintain a 1-1/2 inch (38 mm) overlap between the slip section and the pipe section on the HEAT & GLO SL-550TRSI-AUE.

For horizontal runs, the HEAT & GLO SL-550TRSI-AUE flue system must be supported every 1.5 m. For vertical runs, it must be supported every 2.4 m above the heater flue outlet by wall brackets.

Yes, for horizontal runs, firestops are required on both sides of a combustible wall through which the HEAT & GLO SL-550TRSI-AUE flue passes. For vertical runs, one firestop is required at the hole in each ceiling through which the flue passes.

The termination cap for the HEAT & GLO SL-550TRSI-AUE must be positioned so that the arrow is pointing up.

If joints between the finished walls and the HEAT & GLO SL-550TRSI-AUE surround (top and sides) are sealed, a 149° C minimum sealant material must be used. These joints are not required to be sealed.

When finishing the HEAT & GLO SL-550TRSI-AUE, never obstruct or modify the air inlet/outlet grilles in any manner.

Verify that the incoming gas line ball valve is open, ensure the ignitor gap is correctly set (0.43 cm from ignitor to pilot hood), and ensure the module is securely grounded to the metal chassis of the HEAT & GLO SL-550TRSI-AUE.

This indicates that the batteries in the HEAT & GLO SL-550TRSI-AUE are low. Replace them with quality alkaline batteries.

Typically, the top 10 mm of the thermocouple on the HEAT & GLO SL-550TRSI-AUE should be engulfed in the pilot flame.

The dress guard is fitted to the HEAT & GLO SL-550TRSI-AUE to reduce the risk of fire or injury from burns and no part of it should be permanently removed.

Yes, do not spray aerosols in the vicinity of the HEAT & GLO SL-550TRSI-AUE while it is in operation.

No, do not connect 240 VAC to the gas control valve or control wiring system of the HEAT & GLO SL-550TRSI-AUE.

Do not use the HEAT & GLO SL-550TRSI-AUE if any part has been under water. Immediately call a qualified service technician to inspect the unit and replace any part of the control system and any gas control which has been under water.

After the gas pipe installation for the HEAT & GLO SL-550TRSI-AUE is complete, check all gas connections for leaks with a commercially available, non-corrosive leak check solution. Rinse off all solution following testing. Do not use an open flame.

The heat shield on the Heat & Glo SL-550TRSI-AUE protects the area from elevated header temperatures; do not remove it as it may cause a fire.

The fan in the Heat & Glo SL-550TRSI-AUE is wired in series with a speed control switch and a temperature sensor switch. Once the speed control is set to an ON position, the temperature sensor will automatically start the fan when it warms up and stop it when it cools down.

When using DVP pipe with the Heat & Glo SL-550TRSI-AUE, cut a 254 mm x 254 mm hole. When using SLP pipe, cut a 229 mm x 229 mm hole.

Once the flue cap on the Heat & Glo SL-550TRSI-AUE has been removed, it cannot be reattached.

The Heat & Glo SL-550TRSI-AUE requires 240 VAC to be wired to the factory installed junction box. If any original wire as supplied with the appliance must be replaced, it must be replaced with type 105° C rated wire.