LENOVO THINKVISION T24D-40 (01) PDF Document

The LENOVO THINKVISION T24D-40 package includes an information flyer, a stand, a base, the flat panel monitor, a power cord, a DisplayPort cable, and a Type C-C cable.

Step 1. Take out the top cushion and accessories.

Step 2. Insert the three tabs on the upper part of the stand into the groove on the back of the monitor and press the stand down until it snaps into place.

Step 3. Insert the base towards the stand and tighten the thumbscrew.

Step 4. Stand up the LENOVO THINKVISION T24D-40 with both hands carefully.

Do not touch the monitor within the screen area as it is glass and can be damaged by rough handling or excessive pressure.

The LENOVO THINKVISION T24D-40 has a USB 3.2 Gen 1 Type-A downstream port to connect a USB device, a USB-C downstream port to connect a USB-C device, and another USB 3.2 Gen 1 Type-A downstream port to connect a USB device.

Use the stand release button located on the LENOVO THINKVISION T24D-40 to release the stand from the monitor.

The button labeled 1 is the power on/off button to turn the LENOVO THINKVISION T24D-40 on or off.

You can use the function buttons on the back of the LENOVO THINKVISION T24D-40 to navigate and adjust settings in the on-screen display menu.

The LENOVO THINKVISION T24D-40 features a cable management slot to organize cables by routing them through the slot.

Yes, the LENOVO THINKVISION T24D-40 has VESA mounting holes (100 mm x 100 mm) for wall-mounting through a VESA compatible wall-mount kit.

Use the HDMI 1.4 port on the back of the LENOVO THINKVISION T24D-40 to connect it to your computer using an HDMI cable.

The DP out port is used to connect the LENOVO THINKVISION T24D-40 to another monitor using a DisplayPort cable.

Yes, the LENOVO THINKVISION T24D-40 has an Ethernet port to connect one end of a network cable to the monitor.

The LENOVO THINKVISION T24D-40 has integrated dual speakers that support audio transmitted over the DisplayPort, HDMI, or Type-C video input.

The LENOVO THINKVISION T24D-40 tilt range is from -5 degrees to 23.5 degrees.

The LENOVO THINKVISION T24D-40 can swivel 45 degrees to the left and 45 degrees to the right.

To perform height adjustment on the LENOVO THINKVISION T24D-40, you need to press down or lift up the monitor.

Before rotating the LENOVO THINKVISION T24D-40 screen, ensure it is at its highest point and inclined backward at 23.5 degrees. Then, rotate the monitor clockwise or counterclockwise until it stops at 90 degrees.

Connect one end of the network cable to the Ethernet interface on the LENOVO THINKVISION T24D-40 and the other end to your router.

The LENOVO THINKVISION T24D-40 USB ports have different power outputs: the bottom USB-A port provides 5V/0.9A, the left USB-A port provides 5V/0.9A, and the upper USB-A BC1.2 port provides 5V/2.4A.

This occurs when the system is set to a display mode not supported by the LENOVO THINKVISION T24D-40. If replacing an old monitor, reconnect the old one and adjust the display mode to within the supported range for the LENOVO THINKVISION T24D-40. If using a Windows system, restart in safe mode and select a supported display mode.

Ensure the video signal cable is firmly plugged into the system and the LENOVO THINKVISION T24D-40. You may also need to select another color setting from the OSD menu or perform an automatic image setup.

Ensure the power cord is connected properly to the LENOVO THINKVISION T24D-40 and to a powered outlet. Try turning on the monitor, using a different power cord, or using a different electrical outlet.

The LENOVO THINKVISION T24D-40 is likely in Standby or Suspend mode. Press any key on your keyboard or move the mouse to restore operation, or check the power options settings on your computer.

Step 1. Download the driver for the LENOVO THINKVISION T24D-40 from the provided official support website.

Step 2. Right-click the Windows Start button, select Device Manager, and double-click Monitor.

Step 3. Double-click Generic Monitor, click the Driver tab, and select Update Driver.

Step 4. Select Browse Computer to find the driver, then select Let me pick from a list of available drivers.

Step 5. Click the Have Disk button, browse to the folder where you downloaded the driver, select the t24d-40.inf file, and click Open and OK.

Step 6. Select LENOVO THINKVISION T24D-40 in the window and click Next to finish the installation.

Lightly dampen a soft cloth with water and use this to gently wipe the covers and screen of the LENOVO THINKVISION T24D-40. Remove grease or finger marks with a damp cloth and a little mild detergent.

Do not apply water or liquid directly to the LENOVO THINKVISION T24D-40. Do not use solvents, abrasives, flammable cleaning materials, or any cleaner containing an anti-static solution or similar additives, as these may damage the screen coating. Do not touch the screen area with sharp or abrasive items.

Step 1. Place the LENOVO THINKVISION T24D-40 on a soft and flat surface.

Step 2. Press and hold the stand release button.

Step 3. Lift the stand up and away from the LENOVO THINKVISION T24D-40.

The LENOVO THINKVISION T24D-40 uses a 100mm x 100mm mounting distance and requires M4 x 10 mm screws.

The LENOVO THINKVISION T24D-40 has a depth of 190.0 mm, a height of 505.8 mm, and a width of 539.8 mm.

The LENOVO THINKVISION T24D-40 has a viewable image size of 60.45 cm (23.8 in.).

The LENOVO THINKVISION T24D-40 consumes less than 157 W (maximum) and less than 16 W (typical) in normal operation.

Direct access controls on the LENOVO THINKVISION T24D-40 are active when the OSD menu is not displayed. Use the Left button to return to the previous menu or exit. Use the Up or Down buttons to increase or decrease values. Use the Input Source button to switch the video source. Use the Menu button to access the OSD or confirm selections. Use the Right button to enter submenus.

Press and hold the Menu button on the LENOVO THINKVISION T24D-40 for 10 seconds to lock or unlock the OSD menu.

Press and hold the Input Source button on the LENOVO THINKVISION T24D-40 for 10 seconds to enable or disable DDC/CI.

The LENOVO THINKVISION T24D-40 supports several factory-optimized display modes, including: 640×480 at 60Hz/67Hz/72Hz/75Hz, 800×600 at 60Hz/72Hz/75Hz, 1024×768 at 60Hz/70Hz/75Hz, 1280×1024 at 60Hz/75Hz, and 1920×1080 at 60Hz/75Hz/100Hz/120Hz.

The native resolution of the LENOVO THINKVISION T24D-40 is 1920×1080 at 60 Hz.

The LENOVO THINKVISION T24D-40 power management is invoked when the computer recognizes that you have not used the mouse or keyboard for a user-definable period. In Standby/Suspend mode, the indicator turns amber and the screen goes blank.

The LENOVO THINKVISION T24D-40 has an Energy Star power consumption (PON) of 14 W and an ETEC of 50 kWh.

The LENOVO THINKVISION T24D-40 operates optimally in temperatures between 0 to 40 degrees Celsius and humidity levels between 10% to 80% non-condensing.

When using DisplayPort or USB-C (USB 2.0) with 1920×1080 60Hz / 8bits, the LENOVO THINKVISION T24D-40 supports up to 3 monitors in a daisy chain. When using USB-C (USB 3.0), it supports up to 2 monitors.

The Color Mode menu on the LENOVO THINKVISION T24D-40 allows selection of sRGB, BT.709, Neutral, Warm, Cool, or Custom settings (red, green, blue adjustments).

The Aspect ratio setting on the LENOVO THINKVISION T24D-40 allows you to choose between Full Screen and Original AR modes.

The LENOVO THINKVISION T24D-40 Information menu displays the model name, refresh rate, and firmware serial number.

You can use the Factory reset option in the LENOVO THINKVISION T24D-40 Menu settings to reset or cancel the reset process.

The OSD rotation function on the LENOVO THINKVISION T24D-40 allows you to rotate the display orientation to Normal, 90, 180, or 270 degrees.

The Over Drive function on the LENOVO THINKVISION T24D-40 can be set to Off, Normal, or Extreme to adjust the response time.

On the LENOVO THINKVISION T24D-40, you can select between USB 3.0 or USB 2.0 speeds, available only under USB-C source.

Yes, the LENOVO THINKVISION T24D-40 includes a USB always-on feature, which enables the charging function in all downstream ports when the monitor is without the upstream cable and in standby or off mode.

The LENOVO THINKVISION T24D-40 Scenario mode options include Panel native, Image creation, Video creation, and E-Book mode.

The LENOVO THINKVISION T24D-40 allows selecting between DP 1.4 or DP 1.2, provided you are using a DP source.

The use of Extreme Mode (response time) on the LENOVO THINKVISION T24D-40 may result in reduced display quality when fast-moving video graphics are displayed. Users should verify compatibility with their specific applications.

The LENOVO THINKVISION T24D-40 display uses a low blue light panel that complies with TÜV Rheinland Low Blue Light Hardware Solution certification under factory default settings.

The LENOVO THINKVISION T24D-40 offers Smart Power charging and Priority USB-C charging modes.

Yes, the LENOVO THINKVISION T24D-40 allows adjustment of the OSD position from 0 to 100 on both horizontal and vertical axes.

The LENOVO THINKVISION T24D-40 Ethernet setting can be toggled On or Off in the Port settings menu.

The Mirrored power button feature on the LENOVO THINKVISION T24D-40 can be set to On or Off, depending on the connection status and monitor configuration.

The LENOVO THINKVISION T24D-40 supports refresh rates of 50 Hz, 60 Hz, 100 Hz, and 120 Hz for 1080p resolution.