FORD BRONCO 2022 (01) PDF MANUAL

FREE ENGLISH FORD BRONCO 2022 (01) PDF USER GUIDE

FREE ENGLISH FORD BRONCO 2022 (01) PDF USER MANUAL

FREE ENGLISH FORD BRONCO 2022 (01) PDF OWNER GUIDE

FREE ENGLISH FORD BRONCO 2022 (01) PDF OWNER MANUAL

FREE ENGLISH FORD BRONCO 2022 (01) PDF REFERENCE GUIDE

FREE ENGLISH FORD BRONCO 2022 (01) PDF INSTRUCTION GUIDE

FREE ENGLISH FORD BRONCO 2022 (01) PDF REFERENCE MANUAL

FREE ENGLISH FORD BRONCO 2022 (01) PDF INSTRUCTION MANUAL

FREE ENGLISH FORD BRONCO 2022 (01) PDF OPERATING INSTRUCTIONS

CLICK HERE TO DOWNLOAD FORD BRONCO 2022 (01) PDF MANUAL

If this is not the document you want for this product, click here to see if we have any other documents for this product.

FORD BRONCO 2022 (01) PDF SUMMARY:

What is the correct procedure for fastening and unfastening the seatbelts?

All seatbelts in the vehicle are a three-point combination lap and shoulder seatbelt. To fasten, pull the seatbelt out steadily and insert the tongue into the buckle. Pull the seatbelt tight to remove any slack. To unfasten, press the red button on the buckle to release the seatbelt. Hold the seatbelt tongue and let it retract completely and smoothly to its stowed position.

What is sensitive locking mode and how does it work?

Sensitive locking mode is a seatbelt retractor feature that allows shoulder belt length adjustment according to your movements and locking in response to vehicle movement. If the driver suddenly brakes, turns a corner sharply, or the vehicle receives an impact of about 5 mph (8 km/h) or more, the seatbelts lock to help reduce forward movement of the driver and passengers. The seatbelt retractor also locks if you pull the seatbelt webbing out too quickly. If the retractor does not unlock, pull the seatbelt out slowly then feed a small length of webbing back toward the stowed position. When driving off-road or at a severe angle, the seatbelt mechanism locks, and it does not allow you to pull the seatbelt webbing out until your vehicle is on nearly level ground.

What is automatic locking mode?

Automatic locking mode is a safety feature built into the seatbelt retractors that keeps the seatbelts pre-locked.

How do you engage the automatic locking mode?

Fasten the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until you pull the entire belt out. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the seatbelt is now in the automatic locking mode.

How do you disengage the automatic locking mode?

Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive locking mode.

How should seatbelts be adjusted during pregnancy?

Pregnant women should always wear their seatbelt. Position the lap belt portion of a combination lap and shoulder belt low across the hips below the belly and worn as tight as comfort allows. Position the shoulder belt to cross the middle of the shoulder and the center of the chest.

How does the seatbelt reminder system work?

This system monitors all seating positions and provides audio and graphic feedback.

What do the seatbelt reminder indicators mean?

This lamp illuminates if you do not fasten your seatbelt when you switch the ignition on. The lamp switches off when you fasten your seatbelt or about one minute has elapsed. When the initial warning expires for the driver, more warnings are provided for the driver and front passenger. This lamp illuminates if you or your front passenger do not fasten the seatbelt buckle and the vehicle speed exceeds 6 mph (9.7 km/h). This lamp illuminates when you switch the ignition on, identifying the number of seating positions with fastened buckles. It illuminates again when a seating position changes from unfastened to fastened. This warning displays if an occupant unfastens the rear seatbelt buckle or it becomes unfastened. Front seating positions appear in this warning display. Warnings for unfastened front seatbelt buckles appear in the initial warning lamp. Vehicles with two doors do not have a rear center seating position.

How do you view the seatbelt status?

To view the seatbelt status, use the information display controls on the steering wheel. The status includes: Seatbelt fastened, Seatbelt not fastened, Seatbelt recently unfastened, and Fault.

How do you switch the seatbelt reminder on and off?

The driver and front passenger warnings switch off independently. When you perform this procedure for one seating position, do not buckle the other position as this cancels the process. If you are using MyKey, you cannot disable the seatbelt reminder. Also, if the seatbelt reminder has been previously disabled, it will be re-enabled during the use of MyKey. Read Steps 1 – 4 before proceeding with the programming procedure. Make sure that: The parking brake is set, the transmission is in park (P), the ignition is off, and the driver and front passenger seatbelts are unfastened. 1. Switch the ignition on. Do not start the engine. 2. After Step 1, wait an additional five seconds before proceeding with Step 3. Once you start Step 3, you must complete the procedure within 30 seconds. 3. For the seating position you are switching off, buckle then unbuckle the seatbelt four times at a moderate speed, ending in the unbuckled state. After Step 3, the seatbelt warning light switches on. 4. When the seatbelt warning light is on, buckle then unbuckle the seatbelt. After Step 4, the seatbelt warning light flashes for confirmation. This switches the feature off for that seating position if it is currently on and switches the feature on for that seating position if it is currently off.

What should be checked when inspecting seatbelts?

Check the seatbelts and child restraints periodically to make sure they work properly and are not damaged. Make sure there are no nicks, tears or cuts. Replace if necessary. Check all of the following seatbelt assemblies after a crash: Retractors, Buckles, Front seatbelt buckle assemblies, Buckle support assemblies, Child restraint LATCH and tether anchors, and Attaching hardware.

What are the steps to install a child restraint using seatbelts?

Position the child restraint in a seat with a seatbelt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child restraint according to the child restraint manufacturer’s instructions. Make sure you did not twist the belt webbing. 4. Insert the belt tongue into the proper buckle for that seating position until the latch engages. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until you pull all of the seatbelt out. The automatic locking mode is available on the front passenger and rear seats. This vehicle does not require the use of a locking clip. 6. Allow the belt to retract to remove slack. The seatbelt clicks as it retracts to indicate it is in the automatic locking mode. 7. Pull the seatbelt out of the retractor to make sure the retractor is in the automatic locking mode. You should not be able to pull more belt out. If the retractor is not locked, unbuckle the belt and repeat Steps 5 and 6. 8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that exists once you add the extra weight of the child to the child restraint. It also helps to achieve the proper snugness of the child restraint to your vehicle. Sometimes, a slight lean toward the buckle helps to remove remaining slack from the belt. 9. If the child restraint has a tether strap, attach it. 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 in (2.5 cm) of movement. We recommend checking with a NHTSA Certified Child Passenger Safety Technician to make certain the child restraint is properly installed. In Canada, check with Transport Canada for referral to a Child Car Seat Clinic.

What is the LATCH system?

The Lower Anchors and Tethers for CHildren (LATCH) system has three vehicle anchor points: Two lower anchors where the vehicle seat backrest and seat cushion meet, called the seat bight and one top tether anchor behind that seating position. LATCH compatible child restraints have two rigid or webbing mounted attachments. These attachments connect to the two lower anchors at the LATCH equipped seating positions in the vehicle. This type of attachment method eliminates the need to use seatbelts to attach the child restraint. However, you can still use the seatbelt to attach the child restraint if the lower anchors are not used. For forward facing child restraints, you must also attach the top tether strap to the proper top tether anchor if a top tether strap has been provided with your child restraint.

Can you install a child restraint in a center seat using LATCH?

You cannot install a child restraint with rigid LATCH attachments at the center seating position. You can only use LATCH compatible child restraints, with attachments on belt webbing, at this seating position provided that the child restraint manufacturer’s instructions permit use with the anchor spacing stated. Do not attach a child restraint to any lower anchor if another child restraint is attached to that anchor. Each time you use the child restraint, check that the seat is properly attached to the lower anchors and tether anchor, if applicable. Tug the child restraint from side to side and forward and back where it is secured to the vehicle. The seat should move less than 1 in (2.5 cm). If you did not properly anchor the child restraint, the risk of a child being injured in a crash greatly increases.

What is the proper way to install a tether strap?

Route the child restraint tether strap over the back of the seat. For the outermost seating positions, route the tether strap under the head restraint and between the head restraint posts. For vehicles with a center seating position, route the tether strap over the top of the head restraint. If needed, you can also remove the head restraints. The head restraints are not removable on 2-door vehicles. Locate the correct anchor behind the gap cover for the selected seating position. Clip the tether strap to the anchor. Tighten the child restraint tether strap according to the manufacturer’s instructions. If your child restraint system has a tether strap, and the child restraint manufacturer recommends its use, it is also recommended that it is used.

What is the proper way to use a booster seat?

Use a belt-positioning booster seat for children who have outgrown or no longer properly fit in a child restraint and meet the following criteria: Generally children who are less than 57 in (1.45 m) tall, are greater than age four (4) and less than age twelve (12), and are between 40 lb (18 kg) and 80 lb (36 kg) and upward to 100 lb (45 kg). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 57 in (1.45 m) tall, or 80 lb (36 kg). Booster seats should be used until you can answer yes to all of these questions when seated without a booster seat: Can the child sit all the way back against their vehicle seat backrest with knees bent comfortably at the edge of the seat cushion? Can the child sit without slouching? Does the lap belt rest low across the hips? Is the shoulder belt centered on the shoulder and chest? Can the child stay seated like this for the whole trip? Always use booster seats in conjunction with your vehicle lap and shoulder belt.

What are the different types of booster seats?

Backless booster seats: If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat backrest or no head restraint, a backless booster seat may place your child’s head, as measured at the tops of the ears, above the top of the seat. In this case, move the backless booster to another seating position with a higher seat backrest or head restraint and lap and shoulder belts, or consider using a high-back booster seat. High-back booster seats: If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high-back booster seat would be a better choice.

How do child safety locks work?

A child safety lock is on the rear edge of each rear door. Switch the child safety lock separately on each door. For the left-hand side, turn the key clockwise to switch the child lock on and counterclockwise to switch it off. For the right-hand side, turn the key counterclockwise to switch the child lock on and clockwise to switch it off. You cannot open the rear doors from inside if you have put the child safety locks on.

How do you use cruise control?

See Setting the Cruise Control Speed (page 232) for setting the speed, Switching Cruise Control On and Off (page 232) for on/off, and Resuming the Set Speed (page 233).

How do you use Adaptive Cruise Control?

See Setting the Adaptive Cruise Control Speed (page 237) for setting speed, Setting the Adaptive Cruise Control Gap (page 238) for setting distance, Switching the Lane Keeping System On and Off (page 250) for on/off, and Resuming the Set Speed (page 239).

How do you use the Instrument Cluster Display Controls?

See Using the Instrument Cluster Display Controls (page 113).

How do you use Voice Interaction?

See What is Voice Interaction (page 436).

How do you use the audio system?

See Playing or Pausing the Audio Source (page 422) for play/pause and Adjusting the Volume (page 423) for volume.

Where is the exterior lighting control?

See Exterior Lighting Control (page 94).

How do you use the instrument cluster?

See Instrument Cluster Overview (page 107).

How do you start a gasoline engine?

See Starting a Gasoline Engine (page 152).

How do you use the feature bar?

See Feature Bar (page 434).

How do you switch the audio unit on and off?

See Switching the Audio Unit On and Off (page 422).

How do you open the glove compartment?

See Opening the Glove Compartment (page 149).

How do you identify the climate control unit?

See Identifying the Climate Control Unit (page 118).

How do you apply the electric parking brake?

See Applying the Electric Parking Brake (page 198).

How do you open and close the hood?

See Opening and Closing the Hood (page 320).

Where are the power outlets located?

See Locating the Power Outlets (page 147).

How do you select a four-wheel drive mode?

See Selecting a Four-Wheel Drive Mode (page 184).

How do you shift into reverse in a manual transmission?

See Shifting Into Reverse (page 174).

What are the recommended shift speeds in a manual transmission?

See Recommended Shift Speeds (page 175).

How do you use crawler gear in a manual transmission?

See Using Crawler Gear (page 174).

How do you adjust the exterior mirrors?

See Adjusting the Exterior Mirrors (page 106).

How do you open and close the windows?

See Opening and Closing the Windows (page 103).

How do you move the seat backward and forward?

See Moving the Seat Backward and Forward (page 129).

How do you fold the seats?

See Folding the Seats (page 135).

Where are the rear cargo area anchor points located?

See Locating the Rear Cargo Area Anchor Points (page 280).

How do you remove and install the front roof panel?

See Removing and Installing the Front Roof Panel (page 350).

How do you remove and install the doors?

See Removing and Installing the Doors (page 342).

How do you remove the fender flares?

See Removing the Fender Flares (page 359).

How do you access the front towing point?

See Accessing the Front Towing Point (page 305).

How do you open and close the soft top?

See Opening and Closing the Soft Top (page 354).

How do you change a flat tire?

See Changing a Flat Tire (page 395).

How do you remove and install the rear roof panel?

See Removing and Installing the Rear Roof Panel (page 351) for 2-door models and (page 352) for 4-door models.

How do you store the roof panels?

See Storing the Roof Panels (page 366) for 2-door models and Storing the Doors and the Roof Panels (page 360) for 4-door models.

What are the recommended towing weights?

See Recommended Towing Weights (page 287).

How do you remove and install the rear window?

See Removing and Installing the Rear Window (page 340).

How do you remove and install the soft top?

See Removing and Installing the Soft Top (page 357).

How do you lock and unlock the tailgate?

See Locking and Unlocking the Tailgate (page 84).

How do you shift your vehicle into gear?

See Shifting Your Vehicle Into Gear (page 179).

How do you adjust the seat backrest?

See Adjusting the Seat Backrest (page 135).

What should you do with seatbelt assemblies after a crash?

We recommend that all seatbelt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Seatbelt assemblies not in use during a crash should also be checked and replaced if either damage or improper operation is noted.

Should a person who fits into the vehicle’s seatbelt use an extension?

No, persons who fit into the vehicle’s seatbelt should not use an extension. Unnecessary use could result in serious personal injury in the event of a crash.

Where can you obtain seatbelt extensions?

Only use extensions provided free of charge by our dealers. The dealer will provide an extension designed specifically for this vehicle, model year, and seating position.

Can you use a seatbelt extension to install a child restraint?

No, never use seatbelt extensions to install child restraints.

Can you use seatbelt extensions to change how the seatbelt fits?

No, do not use extensions to change the way the seatbelt fits across the torso, over the lap, or to make the seatbelt buckle easier to reach.

How do the front airbags work?

The driver and front passenger airbags deploy during significant frontal and near frontal crashes. The airbags are a supplemental restraint system and are designed to work with the seatbelts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag.

What should you expect when an airbag deploys?

You will hear a loud bang and see a cloud of harmless powdery residue. This is normal. The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. Contact with a deploying airbag may cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag.

What is a risk of injury from a deploying airbag?

Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries, or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment.

What should you do to minimize the risk of injury from an airbag?

It is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control.

Is routine maintenance of airbags required?

No, routine maintenance of the airbags is not required.

Where are the side airbags located?

The side airbags are on the outermost side of the seat backrests of the front seats.

When will the side airbags inflate?

In certain sideways crashes or rollovers, the airbags will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided to occupants in side impact crashes.

Where is the Safety Canopy mounted?

The Safety Canopy is mounted to the roof side rail sheet metal, behind the side rail trim, above each row of seats.

When does the Safety Canopy deploy?

The Safety Canopy deploys during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor.

What should you do to properly position yourself away from the airbag?

Move your seat to the rear as far as you can while still reaching the pedals comfortably.
Recline the seat slightly one or two degrees from the upright position.

How should occupants sit in their seats?

Properly seated occupants sit upright, lean against the seat backrest, and center themselves on the seat cushion, with their feet comfortably extended on the floor.

When is the front passenger frontal airbag disabled?

The front passenger sensing system is designed to disable the front passenger frontal airbag under these conditions:

The front passenger seat is unoccupied.
The system determines an infant is present in a child restraint.
A passenger takes their weight off of the seat for a period of time.
If there is a problem with the airbag system or the passenger sensing system.

What does it mean when the passenger airbag status indicator illuminates the off lamp?

When the front passenger sensing system disables the front passenger frontal airbag, the passenger airbag status indicator illuminates the off lamp.

What does it mean when the passenger airbag status indicator illuminates the on lamp?

When the front passenger sensing system enables the front passenger frontal airbag, the passenger airbag status indicator illuminates the on lamp.

What should you do if the passenger airbag status indicator off lamp is illuminated when a person of adult size is sitting in the front passenger seat?

Switch your vehicle off and ask the person to place the seat backrest in an upright position.
Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended.
Restart your vehicle and have the person remain in this position for about two minutes. This allows the system to detect that person and enable the passenger frontal airbag.
If the indicator off lamp remains illuminated even after this, you should advise the person to ride in the rear seat.

What should you check for if you think that the state of the passenger airbag status indicator lamp is incorrect?

Objects lodged underneath the seat.
Objects between the seat cushion and the center console.
Objects hanging off the seat backrest.
Objects stowed in the seat backrest map pocket.
Objects placed on the occupant’s lap.
Cargo interference with the seat
Other passengers pushing or pulling on the seat.
Rear passenger feet and knees resting or pushing on the seat.

What should you do if the airbag readiness light is on?

Pull your vehicle over.
Switch your vehicle off.
Check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.
Remove the obstruction if found.
Restart your vehicle.
Wait at least two minutes and verify that the airbag readiness light in the instrument cluster is no longer illuminated.
If the airbag readiness light in the instrument cluster remains illuminated, there may be a problem due to the front passenger sensing system.
Do not attempt to repair or service the system. Take your vehicle in for service immediately.

What are the front passenger sensing system indicators?

Passenger Airbag Status Indicator	Occupant
OFF: Illuminated	Empty
ON: Not Illuminated
OFF: Illuminated	Child
ON: Not Illuminated
OFF: Not Illuminated	Adult
ON: Illuminated

What does the restraints control module activate during a crash?

Front and rear seatbelt pretensioners.
Driver airbag.
Passenger airbag.
Seat-mounted side airbags.
Safety Canopy

What indicates a difficulty with the safety system?

The readiness light either flashes or stays on.
You hear a series of five tones. The tone pattern repeats periodically until the problem, the light or both are repaired.

What should you do if there is a difficulty with the safety system?

If any of these things happen, even intermittently, have the supplemental restraint system serviced immediately. Unless serviced, the system may not function properly in the event of a crash.

When do the front airbags activate?

The front airbags activate only in frontal and near-frontal crashes. Front airbags may activate in rollovers, side impacts, or rear impacts if the crash causes sufficient frontal deceleration.

When do the seatbelt pretensioners activate?

The seatbelt pretensioners activate in frontal, near-frontal, and side crashes, and in rollovers.

When do the side airbags inflate?

The side airbags inflate in certain side impact crashes or rollover events. Side airbags may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation.

When does the Safety Canopy inflate?

The Safety Canopy inflates in certain side impact crashes or rollover events. The Safety Canopy may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation, or a certain likelihood of rollover.

What should you do with airbags that need to be disposed of?

Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

What are the requirements for 911 Assist to make an emergency call?

SYNC is powered and working properly at the time of the incident and throughout feature activation and use.
The 911 Assist feature must be set on before the incident.
You must pair and connect a Bluetooth® enabled and compatible cell phone to SYNC.
A connected Bluetooth® enabled phone must have the ability to make and maintain an outgoing call at the time of the incident.
A connected Bluetooth® enabled phone must have adequate network coverage, battery power, and signal strength.
The vehicle must have battery power and be located in the U.S., Canada, or in a territory in which 911 is the emergency number.

What are the limitations of the 911 Assist feature?

Your cellular phone or 911 Assist hardware sustains damage in a crash.
The vehicle’s battery or the SYNC system has no power.
The phone(s) thrown from your vehicle are the ones paired and connected to the system.

What are the conditions that can affect the function of the remote control?

The remote control remains stationary for about a minute.
The vehicle battery has no charge.
The remote control battery has no charge.
There is interference causing issues with the remote control frequencies.
The remote control is too close to metal objects or electronic devices, for example keys or a cell phone.

How do you remove the key blade from the passive key?

Push the release button on your passive key and pull the key blade out.

How do you sound the panic alarm?

Press the button to sound the panic alarm. Press the button again or switch the ignition on to turn it off.

How do you change the remote control battery?

Push the release button and pull the key blade out.
Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover.
Insert a screwdriver, and carefully remove the battery.
Install a new battery with the + facing upward.
Reinstall the battery housing cover onto the transmitter and install the key blade.

How do you program the remote control?

You must have two previously programmed remote controls inside your vehicle and the new, unprogrammed remote controls readily accessible. Make sure that your vehicle is off before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Perform all steps within 30 seconds of starting the sequence. Stop and wait for at least one minute before starting again if you perform any steps out of sequence.

Place the first programmed remote in the backup slot inside the center console. With your foot off the brake pedal, press and release the push button ignition switch.
Wait five seconds and then press and release the push button ignition switch again.
Remove the remote control.
Within 10 seconds, place a second programmed remote control in the backup slot. Press and release the push button ignition switch.
Wait five seconds and then press and release the push button ignition switch again. Keep the ignition on for at least 3 seconds, but no more than 10 seconds.
Remove the remote control.
Place the unprogrammed remote control in the backup slot and press and release the push button ignition switch.

Programming is now complete. With your foot on the brake pedal, press the push button ignition switch to verify the remote control functions operate and your vehicle starts with the new remote control.

What should you do if the remote control programming was not successful?

If programming was not successful, wait 10 seconds and repeat Steps 1 through 7. If you are still unsuccessful, take your vehicle to an authorized dealer.

What are the non-configurable MyKey settings?

Seatbelt Reminder or Belt-Minder™: MyKey mutes the audio system until the front seat passengers buckle the front seat belts.
Satellite Radio: Some Satellite radio channels have restricted access to adult radio content.
Early Low Fuel: The low fuel level warning lamp turns on earlier.
Driving and Parking Aids: You cannot configure settings for parking aids, blind spot information system, and cross-traffic alert. These systems turn on when the vehicle turns on, and you cannot switch them off with a MyKey. You cannot configure settings for pre-collision assist and lane keeping. These systems turn on when the vehicle turns on, but you can switch them off with a MyKey. A new destination in the navigation system can only be set using voice commands when using a MyKey, and with your vehicle moving.

What are the configurable MyKey settings?

Speed Limit: You can set a speed limit for your vehicle. Warning messages appear in the information display and a tone sounds if your vehicle reaches the set speed. You cannot override the set speed when using a MyKey.
Speed Minder: You can set a speed reminder for your vehicle. Warning messages appear in the information display and a tone sounds if your vehicle exceeds the set speed.
Audio System Volume Limit: The audio system maximum volume reduces. A message appears in the information display if you attempt to exceed the volume limit. Automatic volume control turns off.
Emergency Assistance: If you set emergency assistance to always on, you cannot switch it off with a MyKey.
Do Not Disturb: If you set do not disturb to always on, you cannot switch it off with a MyKey. If a phone is connected using Apple CarPlay or Android Auto while driving with a MyKey, the driver can receive phone calls and text messages even if the do not disturb restriction is on, and if the vehicle comes with satellite radio, there is no restriction on the adult content.
Traction and Stability Control: If you set traction control or stability control to always on, you cannot switch it off with a MyKey.

How do you create a MyKey?

Raise the console storage compartment lid.
Place the intelligent access key in the position shown.
Switch the ignition on.
Using your touchscreen, press Menu.
Press Settings.
Press Vehicle.
Press MyKey.
Press Create MyKey.
Press Yes if you want to create the key as a MyKey. A confirmation message appears on the screen.
Switch the ignition off.

How do you program a MyKey?

Switch the ignition on using an admin key.
Press Settings on the touchscreen.
Press Vehicle Settings.
Press MyKey.
Select a setting and press the OK button.
Configure the setting.

How do you clear all MyKeys?

Switch the ignition on using an admin key.
Press Settings on the touchscreen.
Press Vehicle Settings.
Press MyKey.
Press Clear All MyKeys.
Press Yes.

How do you check the MyKey system status?

Switch the ignition on.
Press Settings on the touchscreen.
Press Vehicle Settings.
Press MyKey.
Press MyKey Information.

What should you do if you’re trying to create a MyKey and the admin key is not placed in the backup position?

Place Key in Backup Location.

What should you do if you’re trying to create a MyKey with a key already designated as a MyKey?

Key is Already a MyKey.

What does the message “This Key restricted at Next Key Cycle. Label Key as MyKey” mean?

Displays to confirm that the key is restricted after you switch the ignition off.

How do you unlock the doors using the remote control?

Press the unlock button on the remote control.

How do you lock the doors using the remote control?

Press the lock button on the remote control.

How do you unlock the doors using the central locking?

Press the unlock button on the driver’s side door.

How do you lock the doors using the central locking?

Press the lock button on the driver’s side door.

How do you unlock and open a rear door from the inside?

Pull the interior door handle twice. The first pull unlocks the door, and the second pull opens the door.

What are the requirements for Autounlock?

Autounlock unlocks all the doors when all of the following occur:

The ignition is on, all the doors are closed, and your vehicle is moving at a speed greater than 12 mph (20 km/h).
Your vehicle comes to a stop.
You open the driver door within 10 minutes of switching the ignition off or to the accessory position.

How do you switch Autounlock on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Locks.
Switch Autounlock on or off.

What are the requirements for Autolock?

Autolock locks all the doors when all of the following occur:

All doors are closed.
The ignition is on.
Your vehicle reaches a speed greater than 12 mph (20 km/h).

What are the limitations for Mislock?

When you press the lock button once, the turn signals do not flash if:

Any door or the tailgate is open.
The hood is open.

How do you switch Mislock on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Locks.
Switch Mislock Chirp on or off.

What does the Door Ajar Warning Lamp indicate?

It illuminates when you switch the ignition on and remains on if any door or the hood is open.

What does the Driver Door Ajar message mean?

Displays if a door is open. Fully close the door.

What does the Hood Ajar message mean?

Displays if a hood is open. Fully close the hood.

Can accessories such as steps or handles be used with the latch assembly?

Do not use the door latch assembly to attach any accessory, such as handles or steps, as this can cause damage to your vehicle.

What are the Keyless Entry limitations?

The remote control remains stationary for about a minute.
The vehicle battery has no charge.
The remote control battery has no charge.
There is interference causing issues with the remote control frequencies.
The remote control is too close to metal objects or electronic devices, for example keys or a cell phone.

How do you switch Keyless Entry on and off?

Switch the ignition on using an original key that has not been created as a MyKey.
Press Settings on the touchscreen.
Press Vehicle Settings.
Press Locks.

How do you reprogram the unlocking function?

Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking.

How do you unlock the doors using keyless entry?

With your passive key within 5 ft (1.5 m) of your vehicle, touch the unlock sensor on the back of the door handle for a brief period and then pull on the door handle to unlock, being careful not to touch the lock sensor at the same time or pull on the door handle too quickly. The intelligent access system requires a brief delay to authenticate your passive key.

How do you lock the doors using keyless entry?

With your passive key within 3 ft (1 m) of your vehicle, touch the outer door handle lock sensor for approximately one second to lock, being careful not to touch the unlock sensor on the back of the door handle at the same time. After locking, you can immediately pull on the door handle to confirm locking occurred without inadvertently unlocking.

Why does the keyless entry system not function?

If the system does not function it may be limited. If the system still does not function, use the remote control or the key blade to lock and unlock your vehicle.

Why can’t you lock your vehicle?

If you electronically lock your vehicle with a rear door or the tailgate open, the system searches for a passive key inside your vehicle after you close the last door. If the system detects a key, all doors unlock indicating that a key is inside. Your vehicle locks if another passive key is within the detection range after you close the last door.

Why does the passive key not work?

The system deactivates passive keys left inside your vehicle when you lock it. You cannot switch the ignition on using a deactivated passive key. Press the unlock button on the remote control to reactivate a passive key.

How do you open the tailgate from the outside?

Unlock the vehicle with the remote control or power door unlock control.
Pull the handle to release the tailgate.

How do you close the tailgate from the outside?

Push the tailgate until fully closed.

How do you lock the tailgate with a passive key?

If a passive key is within 5 ft (1 m) of the tailgate, touch the lock button on the tailgate handle to lock.

How do you unlock the tailgate with a passive key?

If a passive key is within 5 ft (1 m) of the tailgate, touch the back of the tailgate handle to unlock.

How do you lock the tailgate in an emergency if there is a power door lock fault?

You can use the key blade to lock the tailgate door.

How do you unlock the tailgate in an emergency if there is a power door lock fault?

Remove the tailgate trim panel.
Remove the inside release lever cover.
Using a small tool, pull the release lever to open the tailgate.
Reinstall the inside release lever cover and trim panel after unlocking the tailgate.

What does the Tailgate Ajar message mean?

The tailgate is not completely closed.

How does the passive anti-theft system work?

The passive anti-theft system arms when you switch the ignition off. It disarms when the ignition is switched on with a correctly coded key.

What should you do if there is a potential alarm problem with your vehicle?

Take all remote controls to an authorized dealer.

What should you do if the vehicle is unable to start with a correctly coded key?

Have your vehicle checked as soon as possible.

How do you adjust the steering wheel?

Unlock the steering column.
Adjust the steering wheel to the position you prefer.
Lock the steering column.

How do you activate the horn?

Press on the center of the steering wheel near the horn icon to activate the horn.

How do you activate the heated steering wheel?

Press the button on the climate control unit.

How do you switch the windshield wipers on and off?

Use the rotary control.

How do you switch the rear window wiper on and off?

Rotate the control away from you for a long wipe interval. Rotate the control toward you for a short wipe interval.

What is reverse wipe?

Reverse wipe turns on the rear window wiper when you shift into reverse ® and the windshield wipers are on.

How do you change the reverse wipe settings?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Wipers.
Switch Rear Wiper On (when in Reverse) on or off.

How do you check the wiper blades?

Run the tip of your fingers over the edge of the blade to check for roughness.

How do you replace the front wiper blades?

Pull the wiper blade and arm away from the glass.
Lift the wiper blade primary locking clip.
Press the wiper blade secondary locking clip.
Remove the wiper blade.
To install, reverse the removal procedure.

How do you replace the rear wiper blades?

Lift the wiper arm.
Remove the wiper blade.
To install, reverse the removal procedure.

How do you operate the windshield washer?

Press and hold the button at the end of the lever to operate the windshield washer.

How do you switch the courtesy wipe on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Wipers.
Switch Courtesy Wipe on or off.

How do you use the rear window washer?

Rotate the control to the top or bottom position and hold it to operate the rear window washer.

How do you make a selection on the exterior lighting control?

Rotate the control to make a selection.

How do you switch the high beam headlamps on?

Push the lever away from you to switch the high beam on.

How do you switch the high beams off?

Push the lever forward again or pull the lever toward you to switch the high beams off.

How do you flash the headlamps?

Slightly pull the lever toward you and release it to flash the headlamps.

How do you access Autolamp settings?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Lighting.

How do you set the Autolamp delay?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Lighting.
Press Autolamp Delay.
Press a setting.

How do you switch the turn signal lamps on and off?

Push the lever up or down to switch the turn signal lamps on. Set the lever to the middle position to switch the turn signal lamps off.

How do you switch the Daytime Running Lamps on and off – for vehicles with configurable DRL?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Lighting.
Switch Daytime Running Lights on or off.

How do you switch the front fog lamps on and off?

Press the button on the lighting control.

How do you switch the spot lamps on and off?

Press the button to switch on the left-hand spot lamp. Press the button to switch on the right-hand spot lamp. Move the position of the exterior mirrors to adjust the aim.

How do you use exterior zone lighting?

Press Features on the touchscreen.
Press Zone Lighting.

How do you set exterior zone lighting settings?

Press Features on the touchscreen.
Press Zone Lighting.
Press the settings menu in the upper right-hand corner.
Press a setting.

How does automatic high beam control work?

Automatic high beam control turns the high beams on if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead, the system turns the high beams off.

How do you switch Automatic High Beam Control on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Lighting.
Switch Auto Highbeam on or off.

How do you override Automatic High Beam Control?

Push the lever away from you to switch the high beams on. Push the lever away from you again to switch the high beams off. Push the lever away from you for a third time to switch automatic high beam control back on.

How do you switch all the interior lamps on and off?

Press the all lamps on button on the overhead console.

How do you switch the front interior lamps on and off?

Press the individual map lamp buttons on the overhead console.

How do you switch the rear interior lamps on and off?

Press the rear interior lamp switch above the rear seat or above the rear windows.

How do you switch the interior lamp function on and off?

Press the interior lamp function button.

How do you adjust the instrument panel lighting brightness?

Repeatedly press one of the buttons on the lighting control to adjust the brightness.

How do you switch ambient lighting on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Ambient Light.
Switch Ambient Light on or off.

How do you adjust ambient lighting?

Drag the slider left or right.

How do you open and close the power windows?

Press the control to open the window. Lift the control to close the window.

How do you open the tailgate window?

Open the tailgate.
Lift the window.

How do you close the tailgate window?

Push the window down.
Close the tailgate.

How do you use Global Opening?

Press and release the unlock button on the remote control.
Press and hold the unlock button on the remote control.
Release the button when the windows start to open. Press the lock or the unlock button on the remote control to stop global opening.

How do you switch Global Opening on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Press Windows.
Switch Remote Open on or off.

How do you override window bounce-back?

Close the window until it reaches the point of resistance and let it reverse.
Lift and hold the window control switch within two seconds to override bounce-back and close the window.

How do you lock the rear window controls?

Press the window control switch to lock or unlock the rear window controls.

How do you manually dim the interior mirror?

Pull the tab below the mirror toward you to reduce glare at night.

How do you adjust the exterior mirrors?

Select the mirror you want to adjust. The control light turns on.
Use the adjustment control to adjust the position of the mirror.
Press the mirror control again. The control light turns off.

How do you fold the exterior mirrors?

Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position.

What does the fuel gauge indicate?

Indicates approximately how much fuel is in the fuel tank.

What is the low fuel reminder?

A low fuel level reminder displays and sounds when the distance to empty reaches 75 mi (120 km) to empty for MyKey, and at 50 mi (80 km), 25 mi (40 km), 12 mi (20 km) and 0 mi (0 km) for all vehicle keys.

What does the distance to empty indicate?

Indicates the approximate distance your vehicle can travel on the fuel remaining in the tank.

What do instrument cluster warning lamps indicate?

Warning lamps alert you to a vehicle condition that could become serious. Some lamps illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.

What should you do if the anti-lock brake system warning lamp illuminates?

If it illuminates when you are driving, this indicates a malfunction. Your vehicle continues to have normal braking without the anti-lock brake system function. Have your vehicle checked as soon as possible.

What should you do if the battery warning lamp illuminates?

If it illuminates when the engine is running this indicates a malfunction. Have your vehicle checked as soon as possible.

What should you do if the brake system warning lamp illuminates when the vehicle is moving?

Make sure the parking brake is released. If the parking brake is released, this indicates low brake fluid level or the brake system requires service. Have your vehicle checked as soon as possible.

What should you do if the engine coolant temperature warning lamp illuminates?

Safely stop your vehicle and switch your vehicle off.

What should you do if the low beam warning lamp illuminates?

Have the system checked as soon as possible.

What should you do if the malfunction indicator lamp illuminates when the engine is on?

This indicates that the emission control system requires service. If it flashes, have your vehicle checked immediately.

What should you do if the oil pressure warning lamp illuminates?

This illuminates when the engine oil pressure is low.

What should you do if the powertrain malfunction warning lamp illuminates?

Have the system checked as soon as possible.

What are the instrument cluster display controls?

Menu button.
Return button.
Up button.
OK toggle button.
Down toggle button.

How do you access the trip computer?

Select Trip/Fuel.
Select Fuel Economy, Trip 1, or Trip 2.

How do you reset the trip computer?

Select Trip/Fuel.
Press and hold the OK button for a few seconds.

How do you set the remote start duration? Using the information display controls on the steering wheel, select Settings. Then, select Vehicle, then Remote Start, and finally select Duration.

How do you switch the climate control on and off? Press the button.

How do you switch recirculated air on and off? Press the button to recirculate air currently in the passenger compartment. Note: Recirculated air may turn off automatically, or prevent you from switching on in all air flow modes except MAX A/C to reduce the risk of fogging. Recirculation may also turn on and off automatically in various air distribution control combinations to improve heating or cooling efficiency.

How do you switch air conditioning on and off? Press the button. Note: Under certain conditions, the air conditioning compressor could continue to operate after you switch air conditioning off. To keep the system and its components fully functional, switch air conditioning on and let your vehicle idle at least once per month for a minimum of two minutes.

How do you switch maximum defrost on and off? Press the button. Air flows through the windshield air vents, the temperature is set to the highest setting, and the blower motor adjusts to the highest speed. You can also use this setting to defog and clear the windshield of a thin covering of ice. To prevent window fogging, you cannot select recirculated air when maximum defrost is on. The heated rear window and heated mirrors also turn on when you select maximum defrost. When maximum defrost is on, the air conditioning compressor may continue to operate even though you switch off the A/C. Or, turn the temperature control clockwise past the highest setting to maximize defrosting. The temperature control springs back to the highest setting. Air flows through the windshield air vents, and the blower motor adjusts to the highest speed. To prevent window fogging, you cannot select recirculated air when maximum defrost is on. The heated rear window also turns on when you select maximum defrost.

How do you switch maximum cooling on and off? Press the button. Air flows through the instrument panel air vents, the temperature is set to the lowest setting, and the blower motor adjusts to the highest speed. When you switch maximum cooling off, air conditioning remains on. Or, turn the temperature control counterclockwise past the lowest setting to maximize cooling. The temperature control springs back to the lowest setting. When you switch maximum cooling off, air conditioning remains on.

How do you switch the heated rear window on and off? Press the button to clear the rear window of thin ice and fog. The heated rear window turns off after a short period of time. This button also activates the heated mirrors. Do not use harsh chemicals, razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window as this could cause damage to the heated rear window grid lines not covered by the vehicle Warranty.

How do you set the blower motor speed? Press up or down on the control to select the blower motor speed. Or, turn the blower motor control counterclockwise for a lower blower setting. Turn the blower motor control clockwise for a higher blower setting. Lights on the control illuminate to indicate the blower motor speed.

How do you switch the heated mirrors on and off? Press the button.

How do you set the temperature? Turn the control on the left-hand side of the climate control to set the left-hand temperature. This control also sets the right-hand side temperature when you switch off dual zone mode. Turn the control on the right-hand side of the climate control to set the right-hand temperature. Or, turn the temperature control counterclockwise for cooler temperature settings. Turn the temperature control clockwise for warmer temperature settings.

How do you direct air to the windshield air vents? Press the button to activate the selection screen, then press the button on the touchscreen. Or, press the button.

How do you direct air to the instrument panel air vents? Press the button to activate the selection screen, then press the button on the touchscreen. Or, press the button.

How do you direct air to the footwell air vents? Press the button to activate the selection screen, then press the button on the touchscreen. Or, press the button.

How do you switch auto mode on and off? Press the button to switch auto mode on. Repeatedly press the button to adjust auto mode. When you switch auto mode on, lights on the blower motor control do not illuminate to indicate the blower motor speed. Adjust the blower motor control or air distribution control to switch auto mode off.

How do you switch dual mode on and off? Press the button.

What are the descriptions for the auto mode indicators?

One indicator illuminated: The blower motor speed is reduced. Use this setting to minimize the amount of noise from the blower motor. This setting increases the time taken to cool the interior.
Two indicators illuminated: The blower motor speed is moderate.
Three indicators illuminated: The blower motor speed is increased. Use this setting to reduce the time taken to cool the interior. This setting increases the amount of noise from the blower motor.

What are some general climate control hints?

Prolonged use of recirculated air may cause the windows to fog up.
You may feel a small amount of air from the footwell air vents regardless of the air distribution setting.
To reduce humidity build-up inside your vehicle, do not drive with the system switched off or with recirculated air always switched on.
Do not place objects under the front seats as this may interfere with the airflow to the rear seats.
Remove any snow, ice or leaves from the air intake area at the base of the windshield.
To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents.

What are some hints for using automatic climate control?

Adjusting the settings when your vehicle interior is extremely hot or cold is not necessary. Automatic mode is best recommended to maintain set temperature.
The system adjusts to heat or cool the interior to the temperature you select as quickly as possible.
For the system to function efficiently, the instrument panel and side air vents should be fully open.
If you press AUTO during cold outside temperatures, the system directs air flow to the windshield and side window air vents. In addition, the blower motor may run at a slower speed until the engine warms up.
If you press AUTO during hot temperatures and the inside of the vehicle is hot, the system uses recirculated air to maximize interior cooling. Blower motor speed may also reduce until the air cools.

How do you quickly heat the interior?

Press AUTO.
Adjust the temperature function to the setting you prefer.

What are the recommended settings for heating?

Press AUTO.
Adjust the temperature function to the setting you prefer. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

How do you quickly cool the interior?

Press MAX A/C.
Drive with the windows open for a short period of time.

What are the recommended settings for cooling?

Press AUTO.
Adjust the temperature function to the setting you prefer. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

How do you defog the side windows in cold weather?

Press and release defrost or maximum defrost.
Adjust the temperature control to the setting you prefer. Use 72°F (22°C) as a starting point, then adjust the setting as necessary.

How do you quickly heat the interior on vehicles with manual temperature control?

Adjust the blower motor speed to the highest speed setting.
Adjust the temperature control to the highest setting.
Direct air to the footwell air vents.

What are the recommended settings for heating on vehicles with manual temperature control?

Adjust the blower motor speed to the center setting.
Adjust the temperature control to the midway point of the hot settings.
Direct air to the footwell air vents.

How do you quickly cool the interior on vehicles with manual temperature control?

Press MAX A/C.
Drive with the windows open for a short period of time.

What are the recommended settings for cooling on vehicles with manual temperature control?

Adjust the blower motor speed to the center setting.
Adjust the temperature control to the midway point of the cold settings.
Direct air to the instrument panel air vents.

How do you defog the side windows in cold weather on vehicles with manual temperature control?

Direct air to the instrument panel and windshield air vents.
Press and release A/C.
Adjust the temperature control to the setting you prefer.
Adjust the blower motor speed to the highest setting.
Direct air toward the side windows.
Close the instrument panel air vents.

What is the cabin air filter? The cabin air filter improves the quality of air in your vehicle by trapping dust, pollen and other particles.

How often should the cabin air filter be replaced? Replace the filter at regular intervals. Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. Using an aftermarket cabin air filter could reduce cabin air filtration and climate control performance.

What are some precautions to take with the front seats?

Do not recline the seat backrest too far as this can cause the occupant to slide under the seatbelt, resulting in personal injury in the event of a crash.
Do not place objects higher than the top of the seat backrest. Failure to follow this instruction could result in personal injury or death in the event of a sudden stop or crash.
Do not adjust the driver seat or seat backrest when your vehicle is moving. This may result in sudden seat movement, causing the loss of control of your vehicle.
It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seatbelts.
Make sure everyone in your vehicle is in a seat and properly using a seatbelt. Failure to follow this warning could result in serious personal injury or death.
All occupants of your vehicle, including the driver, should always keep their whole body inside the vehicle when it is moving.

How should you position yourself in the front seat?

Sit in an upright position with the base of your spine as far back as possible.
Do not recline the seat backrest so that your torso is more than 30 degrees from the upright position.
Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable.
Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 in (25 cm) between your breastbone and the airbag cover.
Hold the steering wheel with your arms slightly bent.
Bend your legs slightly so that you can press the pedals fully.
Position the shoulder strap of the seatbelt over the center of your shoulder and position the lap strap tightly across your hips.

How do you adjust the head restraint on manual seats? Adjust the seat backrest to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position. Pull the head restraint up to raise it. To lower the head restraint: 1. Press and hold the adjust and release button. 2. Push the head restraint down. For vehicles with tilting head restraints: 1. Adjust the seat backrest to an upright driving or riding position. 2. Pivot the head restraint forward toward your head to the preferred position. After the head restraint reaches the forward-most tilt position, pivot it forward again to release it to the rearward, untilted position. Do not attempt to force the head restraint backward after it is tilted. Instead, continue tilting it forward until the head restraint releases to the upright position.

How do you remove the head restraint on manual seats?

Pull up the head restraint until it reaches the highest adjustment position.
Press and hold the button.
Pull up the head restraint. You cannot remove head restraints that have audio system speakers.

How do you install the head restraint on manual seats? Align the steel stems into the guide sleeves and push the head restraint down until it locks.

How do you move the seat backward and forward? Make sure the seat fully locks into place by rocking it backward and forward. Not securing the seat into the locked position can be dangerous in a crash and could cause serious personal injury or death.

How do you adjust the seat backrest? Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Do not place cargo or any objects behind the seat backrest before returning it to the original position. Pull on the seat backrest to make sure that it has fully latched after returning the seat backrest to its original position. An unlatched seat may become dangerous if you stop suddenly or have a crash.

How do you adjust the head restraint on power seats? To raise the head restraint, pull the head restraint up. To lower the head restraint: 1. Press and hold the adjust and release button. 2. Push the head restraint down. To tilt the head restraint: 1. Adjust the seat backrest to an upright driving or riding position. 2. Pivot the head restraint forward toward your head to the preferred position. After the head restraint reaches the forward-most tilt position, pivot it forward again to release it to the rearward, untilted position. Do not attempt to force the head restraint backward after it is tilted. Instead, continue tilting it forward until the head restraint releases to the upright position.

How do you remove the head restraint on power seats?

Pull up the head restraint until it reaches its highest position.
Press and hold the adjust and release button.
Pull up the head restraint. You cannot remove head restraints that have audio system speakers.

How do you install the head restraint on power seats? Align the steel stems into the guide sleeves and push the head restraint down until it locks.

How do you move the power seat backward and forward? There are controls to move the power seats back and forth.

How do you adjust the seat cushion on power seats? There are controls to adjust the seat cushion.

How do you adjust the seat backrest on power seats? Do not place cargo or any objects behind the seatback before returning it to the original position. There are controls to adjust the seat backrest.

How do you adjust the seat height on power seats? There are controls to adjust the seat height.

How do you adjust the lumbar support on power seats? There are controls to adjust the lumbar support.

What are some heated seat precautions?

Use caution when using the heated seat if you are unable to feel pain to your skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions. The heated seat could cause burns even at low temperatures, especially if used for long periods of time.
Do not poke sharp objects into the seat cushion or seat backrest. This could damage the heated seat element and cause it to overheat.
Do not place anything on the seat that blocks the heat, for example a seat cover or a cushion. This could cause the seat to overheat.
Do not place heavy objects on the seat.
Do not operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry.

How do you switch the heated seats on and off? The vehicle must be running to use this feature. Press the heated seat symbol to cycle through the various heat settings and off. The more indicators that display, the warmer the temperature of the seat. The heated seats may remain on after you remote start your vehicle, based on your remote start settings. The heated seats may also turn on when you start your vehicle if they were on when you switched your vehicle off.

How do you adjust the head restraint in the rear seats on a 4-door vehicle? Pull the head restraint up to raise it. To lower the head restraint: 1. Press and hold the adjust and release button. 2. Push the head restraint down. Press the fold button to fold the head restraint.

How do you adjust the head restraint in the rear seats on a 2-door vehicle? Pull the strap to fold the head restraint rearward.

How do you remove the head restraint in the rear seats on a 4-door vehicle?

Pull up the head restraint until it reaches its highest position.
Press and hold the adjust and release button and the unlock and remove button.
Pull up the head restraint.

How do you install the head restraint in the rear seats? Align the steel stems into the guide sleeves and push the head restraint down until it locks.

How do you adjust the rear seat backrest on a 4-door vehicle? Do not place cargo or any objects behind the seat backrest before returning it to the original position. Pull on the seat backrest to make sure that it has fully latched after returning the seat backrest to its original position. An unlatched seat may become dangerous if you stop suddenly or have a crash. Pull the lever up to fold the seat backrest fully forward. Make sure that the area under the seat is free of objects before folding the backrest. To return the seat backrest to the upright position, rotate it up until it locks. To store the removable doors, the seat backrest must be in the upright position. To recline the seat backrest to the optimal seating position, pull the lever up and push the backrest rearward.

How do you fold the rear seats on a 2-door vehicle?

Pull the strap at the front of the seat cushion. Then, flip the seat cushion up to the vertical position.
Pull the strap on the top of the seat backrest to fold it forward.

How do you unfold the rear seats on a 2-door vehicle? Make sure that cargo and other objects are not trapped under the seat cushion and that you return the seat cushion to the full-down position. Failure to do so may prevent the seat from operating properly, which could increase the risk of serious injury in a crash. Rotate the seat backrest upright until it locks in the seating position. Then, move the seat cushion back to the seating position.

How do you switch the rear occupant alert system on and off?

Press Settings on the touchscreen.
Press Vehicle.
Switch Rear Occupant Alert on or off. The default setting is on. Performing a master reset causes the system to switch on again.

What is the message that displays when the rear occupant alert system is activated? “Check rear seats for occupants.” Displays when you switch your vehicle off after the alert conditions are met. The message displays for a short period of time. Press Close to acknowledge and remove the message.

How do you program the garage door opener to your hand-held transmitter?

With your vehicle parked outside of the garage, switch your ignition to the on position, but do not start your vehicle.
Press and release one of the three HomeLink function buttons that you would like to program.
Hold your hand-held garage door transmitter 1–3 in (2–8 cm) away from the HomeLink button you want to program.
Press and hold the hand-held transmitter button you want to program while watching the indicator light on HomeLink. Continue to hold the hand-held button until the HomeLink indicator light flashes rapidly or is continuously on.
Press and hold the HomeLink button you programmed for two seconds, then release. You may need to do this twice to activate the door. If the indicator light stays on, the programming is complete. If the HomeLink indicator flashes rapidly, repeat step 5. If your device still does not operate, you must program your garage door.
To program additional buttons, repeat Steps 1 – 4.

How do you program the garage door opener to your garage door opener motor?

Press the learn button on the garage door opener motor. You have 30 seconds to complete the next two steps.
Return to your vehicle.
Press and hold one of the three HomeLink function buttons you want to program for two seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time.

How do you program the garage door opener to your gate opener motor?

Press and release, every two seconds, your hand-held transmitter until the HomeLink indicator light changes to a rapidly blinking or continuously on light.
Release the hand-held transmitter button.
Press and hold the HomeLink function button you want to program for two seconds, then release. You may need to do this twice to activate the door. If the indicator light stays on, the programming is complete. If the HomeLink indicator flashes rapidly, repeat Step 3. If your device still does not operate, you must program your garage door.
To program additional buttons, repeat Steps 1 – 4.

How do you clear the garage door opener?

Press and hold the outer two function buttons simultaneously for approximately 10 seconds until the indicator light above the buttons flashes rapidly.
When the indicator light flashes, release the buttons. You cannot erase individual buttons.

How do you reprogram the garage door opener? To program a device to a previously trained button: 1.Press and hold the desired button. Do NOT release the button. 2.The indicator light begins to flash after 20 seconds. Without releasing the button, follow programming steps.

How do you play media using the USB port?

Connect your device to the USB port.
Press the audio button on the feature bar.
Select Sources.
Select the USB option.
Press the button to play a track.
Press the button again to pause the track.
Press the button to skip to the next track. Press and hold the button to fast forward through the track.
Press the button once to return to the beginning of a track. Repeatedly press the button to return to previous tracks. Press and hold the button to fast rewind.

How do you charge a device using the USB port? Connect your device to the USB port. You can charge your device through the data transfer USB port when SYNC is on. You can charge your device through the charge only USB port when the vehicle is in accessory mode or when the vehicle is running.

What are the power outlet indicators?

On: When the indicator light is on, the outlet is providing power.
Off: When the indicator light is off, there is no power to the outlet.
Flashing: When the indicator light is flashing, the outlet is in a fault mode.

What do you do if the power outlet is in fault mode?

Unplug your device.
Switch your vehicle off to let the system cool and reset the fault mode.
Switch your vehicle back on, but do not plug your device back in.
With your vehicle on, make sure the indicator light remains on.
Make sure your device does not exceed the power limits and then plug in your device. If a fault occurs again, your device may exceed the capacity available from the power outlet.

What are some precautions to take with the 12V power outlet?

Do not plug optional electrical accessories into the cigar lighter socket. Incorrect use of the cigar lighter can cause damage not covered by the vehicle warranty, and can result in fire or serious injury.
Do not use the power point over the vehicle capacity of 12 V DC 240 W or a fuse could blow.
Do not plug in any device that supplies power to the vehicle through the power points. This could result in damage to vehicle systems.
Do not hang any accessory from the accessory plug.
Always keep the power point caps closed when not in use.
Do not insert objects other than an accessory plug into the power point.
Do not use the power point longer than necessary when the vehicle is off.
Do not leave devices plugged in overnight or when you park your vehicle for extended periods.

How do you charge a wireless device? Place the device on the center of the charging surface with the charging side down. The charging stops after your device reaches a full charge. You can use the charger when the vehicle is in accessory mode, when the vehicle is running, or when SYNC is on.

How do you open the glove compartment? Pull the latch to the left to open.

How do you lock the glove compartment? You can lock the lower glove compartment using the key.

How do you open the center console? Push the latch to open the center console.

How do you lock the center console? You can lock the center console using the key.

How do you access the under floor storage in the luggage compartment? Lift the strap to access the under floor storage in the luggage compartment.

How do you open the glasses holder? Press near the rear edge of the door to open it.

What is the weight limit for the map pocket system? The recommended weight limit for this system is 7 lb (3 kg).

How do you switch the ignition off? When the ignition is on or in accessory mode, press the push button ignition switch once without your foot on the brake pedal.

How do you switch the ignition to accessory mode? When the ignition is off, press the push button ignition switch once without your foot on the brake pedal. All electrical circuits and accessories are operational and the warning lamps and indicators illuminate. Your vehicle has a battery saver feature that shuts your vehicle off when it detects a certain amount of battery drain, or after about 30 minutes of inactivity in accessory mode.

How do you start the engine? With the transmission in park (P), press the brake pedal and the push button ignition switch. An indicator light on the button illuminates when then ignition is on and the engine starts. A valid key must be inside your vehicle to switch the ignition on and start the engine.

What do you do before starting a gasoline engine with a manual transmission?

Make sure the headlamps and electrical accessories are off.
Make sure the parking brake is on.
Make sure the transmission is in neutral.

How do you start a gasoline engine with a manual transmission?

Fully press the clutch pedal. Do not touch the accelerator pedal.
Press the push button ignition switch. The engine may continue cranking for up to 15 seconds or until it starts. The engine takes longer to start at lower temperatures. It may crank for several seconds when very cold.

What do you do before starting a gasoline engine with an automatic transmission?

Make sure that the headlamps and electrical accessories are off.
Make sure that the parking brake is on.
Make sure that the transmission is in park (P).

How do you start a gasoline engine with an automatic transmission?

Fully press the brake pedal. Do not touch the accelerator pedal.
Press the push button ignition switch. The engine may continue cranking for up to 15 seconds or until it starts. The engine takes longer to start at lower temperatures. It may crank for several seconds when very cold.

How do you restart the engine after stopping it? Within 10 seconds of switching the engine off, fully press the brake or clutch pedal and press the push button ignition switch. After 10 seconds, you can no longer start the engine if the system does not detect a valid passive key.

What should you do when using an engine block heater?

Use a 16-gauge outdoor extension cord that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard.
Use as short an extension cord as possible.
Do not use multiple extension cords.
Make sure that when in operation, the extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.
If the block heater cord is under the hood, do not remove the wiring from its original location. Do not close the hood on the extension wiring.
Make sure your vehicle is parked in a clean area, clear of combustibles.
Make sure the heater, heater cord and extension cord are firmly connected.
Check for heat anywhere in the electrical hookup once the system has been operating for about 30 minutes.
Make sure the system is unplugged and properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use.
Make sure the heater system is checked for proper operation before winter.

How do you stop the engine when your vehicle is stationary with a manual transmission?

Shift into neutral.
Apply the parking brake.
Wait until the engine reaches idle speed.
Press the push button ignition switch.

How do you stop the engine when your vehicle is stationary with an automatic transmission?

Shift into park (P).
Apply the parking brake.
Wait until the engine reaches idle speed.
Press the push button ignition switch.

How do you stop the engine when your vehicle is moving with a manual transmission?

Press and hold the push button ignition switch until the engine stops, or press it three times within two seconds.
Shift into neutral and use the brakes to bring your vehicle to a safe stop.
Apply the parking brake.

How do you stop the engine when your vehicle is moving with an automatic transmission?

Press and hold the push button ignition switch until the engine stops, or press it three times within two seconds.
Shift into neutral (N) and use the brakes to bring your vehicle to a safe stop.
Shift into park (P).
Apply the parking brake.

How do you switch automatic engine stop on and off?

Press Settings on the touchscreen.
Press Vehicle Settings.
Switch 30min Max Idle on or off. You cannot permanently switch off the automatic shutdown. If you switch it off, it turns on each time you switch the ignition on.

How can you override automatic engine stop? You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following:

Pressing the brake pedal or accelerator pedal.
Pressing the OK or RESET button during the countdown.

How do you access the passive key backup position?

Open the center console storage compartment lid.
With the buttons facing upward and the unlock button facing the front of your vehicle, place the passive key into the backup slot.
With the key in this position, press the brake pedal then press the push button ignition switch to switch the ignition on and start your vehicle.

When should you shift into crawler gear?

When shifting into crawler ©, make sure your vehicle is completely stationary and that the engine speed is below 1500 RPM. Shift out of crawler © as soon as possible.

What can prolonged use of crawler gear cause?

Prolonged use of crawler © can cause transmission wear and increased fuel consumption.

What should you do before leaving your vehicle?

Apply the parking brake, shift into park (P), switch the ignition off and remove the key before you leave your vehicle.

What should you do when shifting gears while your vehicle is stationary?

Keep the brake pedal fully pressed when shifting gears.

What happens if you apply the brake and accelerator pedal simultaneously for more than a few seconds?

Applying both pedals simultaneously for more than a few seconds will limit engine performance, which may result in difficulty maintaining speed in traffic and could lead to serious injury.

When should you shift into park (P)?

Shift into park (P) only when your vehicle is stationary.

What happens when your vehicle is in park (P)?

Power is not transmitted to the driven wheels.

What might happen if you attempt to exit your vehicle without the transmission in park (P)?

A tone sounds.

What are some reasons your vehicle may not shift out of park (P)?

The vehicle battery has run out of charge.
A fuse is blown.
The key or remote control is not inside your vehicle.

What could happen when the transmission selector is in park (P)?

The electronic parking brake could apply.

When should you shift into reverse ®?

Shift into reverse ® only when your vehicle is stationary.

What happens when your vehicle is in reverse ®?

Power is transmitted to the driven wheels.

What happens when your vehicle is in neutral (N)?

Your vehicle is free to roll and power is not transmitted to the driven wheels.

What is the normal driving position for the best fuel economy?

Drive (D).

What does Drive (D) allow for?

Automatic upshifts and downshifts through all available gears.

What can you do in manual (M)?

You can select a specific gear.

When is it recommended to use Manual (M)?

For driving on hilly or mountainous roads or when towing a trailer.

When is it recommended to use Sport (S)?

For a sportier feel or when driving on hilly or mountainous roads.

How do you shift your vehicle into gear?

Fully press down on the brake pedal.
Press the front button on the shifter and move the gearshift lever into the desired gear.

How do you shift your vehicle into park (P)?

Come to a complete stop.
Press the front button on the shifter, move the gearshift lever and securely latch it in park (P).

How does the SelectShift Automatic transmission gearshift lever work?

It gives you the ability to change gears up or down, without a clutch.

What does SelectShift do to prevent the engine from stalling?

SelectShift still makes some downshifts if it determines that you have not downshifted in time.

What does SelectShift do to prevent damage to the engine from over-revving?

SelectShift still allows you to downshift at any time if it determines that damage to the engine from over-revving does not occur.

Does SelectShift automatically upshift?

No, SelectShift does not automatically upshift, even if the engine is approaching the RPM limit. Shift manually by pressing the + button.

What can happen if you maintain excessive engine revving without shifting?

Engine damage could occur.

What is brake shift interlock?

Brake shift interlock prevents you from shifting out of park (P) when you have switched the ignition on and not pressed the brake pedal.

What should you do before using the brake shift interlock procedure?

Apply the parking brake prior to doing this procedure. Use wheel chocks if appropriate.

What should you verify before driving your vehicle?

Verify that the stoplamps are working.

What does it mean if the brake warning lamp remains illuminated when the parking brake is fully released?

The brakes may not be working properly.

How do you use the brake shift interlock?

Insert a screwdriver between the shifter boot material and trim ring to access the retainer tabs from the top panel trim ring.
Lift the shifter boot upward.
Locate the release lever on the side of the transmission selector lever.
Using a screwdriver, move the release lever toward the front of the transmission selector lever.
When holding the release lever in the forward position, move the transmission selector lever out of the park (P) position and into another gear.

When does the transmission not in park (P) audible warning sound?

You switch your vehicle off before shifting into park (P).
You open the driver door before shifting into park (P).
You unlatch your seatbelt before shifting into park (P) when the driver door is removed.

What modes of operation does the 4×4 with part time engagement system offer?

Two-wheel drive high, four-wheel drive high, and four-wheel drive low.

What does selecting four-wheel drive high or four-wheel drive low provide?

Mechanically locked four-wheel drive power to both the front and rear wheels for use in off-road or slippery conditions such as deep snow, sand or mud.

What does selecting four-wheel drive low provide?

Additional gearing for increased torque multiplication for conditions like deep sand, steep slopes, or pulling heavy objects.

What does the 4×4 with part time engagement system allow for?

Recreational flat towing by putting the transfer case into neutral (N).

What modes of operation does the advanced 4×4 with 4A mode offer?

Two-wheel drive high, four-wheel drive auto, four-wheel drive high, and four-wheel drive low.

What does selecting four-wheel drive auto provide?

The system continuously varies power to the front wheels for optimum performance for all on-road conditions.

What does selecting four-wheel drive high or four-wheel drive low provide?

Electronically locked power to the front and rear wheels for use in off-road or slippery conditions such as deep snow, sand or mud.

What does selecting four-wheel drive low provide?

Additional gearing for increased torque multiplication for conditions like deep sand, steep slopes, or pulling heavy objects.

What does the advanced 4×4 with 4A mode allow for?

Recreational flat towing by putting the transfer case into neutral (N).

What should you always do when driving a four-wheel drive vehicle?

Always drive at a safe speed.

What should you avoid when driving a vehicle with a higher center of gravity?

Avoid sharp turns, excessive speed and abrupt steering.

When should you not use four-wheel drive high or four-wheel drive low mode?

Do not use four-wheel drive high or four-wheel drive low mode on dry, hard surfaced roads.

What can using four-wheel drive high or four-wheel drive low mode on dry, hard surfaced roads cause?

Excessive noise, increased tire wear and can damage driveline components.

When should you use four-wheel drive high or four-wheel drive low mode?

Four-wheel drive high or four-wheel drive low mode is only for use on consistently slippery or loose surfaces.

What can using four-wheel drive low mode on loose surfaces cause?

Some noise, such as occasional clunks, but should not damage driveline components.

What can happen when attempting to shift out of a four-wheel drive mode on dry, hard surfaced roads with an electronic shift-on-the-fly transfer case?

The driveline could become mechanically blocked.

What should you be sure of when transitioning from consistently loose or slippery surfaces to dry, hard surfaced roads in two-wheel drive high with the 4×4 part-time selectable engagement transfer case?

Be sure the four-wheel drive system is not mechanically blocked.

What might appear in the instrument cluster when the four-wheel drive system has difficulty engaging?

A To Engage 4×4 Slow to 3 MPH or To Engage 4×4 Slow to 5 km/h message.

What can also cause the To Engage 4×4 Slow to 3 MPH or To Engage 4×4 Slow to 5 km/h message to appear?

Engaging the four-wheel drive system in extreme cold climates at the beginning of the drive cycle.

What can affect the four-wheel drive system if there is a significant difference between the size of the spare tire and the remaining tires?

You could have limited four-wheel drive functionality, added noise, discomfort and driveline damage.

When driving with a dissimilar wheel and tire assembly, what should you not do?

Exceed 50 mph (80 km/h) when operating in a four-wheel drive mode.
Select a four-wheel drive mode unless the vehicle is stationary.
Use a four-wheel drive mode on dry pavement.

What can you experience when driving with a dissimilar wheel and tire assembly in a mechanically locked four-wheel drive mode?

Additional noise from the transfer case or other drive components.
Difficulty shifting in and out of a mechanically locked four-wheel drive mode.
Driveline component damage.

What factors can affect the shifting performance of an electronic shift-on-the-fly transfer case?

Vehicle acceleration.
Dissimilar tire sizes.
High steering input.

What procedure is recommended to reduce the likelihood of a mechanical shift block when shifting into two-wheel drive high on dry, hard surfaced roads with an electronic shift-on-the-fly transfer case?

When driving straight, come to a complete stop on a flat, horizontal surface.
For vehicles with an automatic transmission, shift into park (P). For vehicles with a manual transmission, press the clutch.
Select 2H and wait for the 2H LED to become solid.
For vehicles with an automatic transmission, shift into reverse ®. For vehicles with a manual transmission, select reverse ® and release the clutch. Let the vehicle roll backward up to 3 ft (1 m) and press the brake.
For vehicles with an automatic transmission, shift into drive (D). For vehicles with a manual transmission, press the clutch in again, select a forward gear and release the clutch. Let the vehicle roll forward up to 3 ft (1 m).

What actions can relieve a mechanical shift block?

Momentary acceleration.
Momentary braking.
Bringing the vehicle to a stop.
Shifting the transmission to neutral and back to drive.
Shifting the transmission to reverse and back to drive.
Driving the vehicle around a tight turn at a slow speed.

What can the ability to use all four wheels to power a vehicle do?

Increases traction, which may enable you to safely drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot.

What might happen during the initial shift from two-wheel drive to four-wheel drive while the vehicle is moving?

A momentary clunk and ratcheting sound. These sounds are normal as the front drivetrain comes up to speed.

How do you select a four-wheel drive mode?

Push the button.

What should you not do when shifting to or from Four-Wheel Drive Low?

Do not perform this operation if the rear wheels are slipping or when applying the accelerator pedal or when driving in a tight turn.

What can improve engagement or disengagement performance when shifting to or from Four-Wheel Drive Low?

Momentarily releasing the accelerator pedal when a shift in progress message displays.

How do you shift to Four-Wheel Drive Low?

Bring your vehicle to a speed of 0 mph (0 km/h).
For vehicles with an automatic transmission, place in neutral (N). For vehicles with a manual transmission, fully depress the clutch pedal.
Push the 4L on the four-wheel drive mode selector.

What happens if the shift conditions are not met when shifting to or from Four-Wheel Drive Low?

The shift should not occur and the information display can guide the driver through the proper shifting procedures.

What should you do if Shift Delayed Drive Forward displays in the information display when shifting to or from Four-Wheel Drive Low?

Place the transmission in a forward gear, move your vehicle forward approximately 5 ft (1.5 m), and shift the transmission back to neutral (N) to allow the transfer case to complete the range shift.

What does it mean when the four-wheel drive mode light is solid?

The system has achieved the desired four-wheel drive mode.

What does it mean when the selected four-wheel drive mode light is blinking?

The system is attempting to shift to that specific four-wheel drive mode.

What does it mean when all the lights are blinking?

Have your vehicle serviced as soon as possible.

What does the instrument cluster display when you achieve recreational towing?

Neutral Tow Enabled Leave Transmission in Neutral.

What is two-wheel drive high for?

General on-road driving. Power is sent to the rear wheels only.

What is four-wheel drive auto for?

Four-wheel drive auto provides electronically controlled four-wheel drive power to both the front and rear wheels, as required, for increased traction in varying on-road conditions.

What is four-wheel drive high for?

Four-wheel drive high provides electronically or mechanically locked four-wheel drive power to both the front and rear wheels for use in off-road or winter conditions such as deep snow, sand or mud. This mode is not for use on dry pavement.

What is four-wheel drive low for?

Four-wheel drive low provides electronically or mechanically locked four-wheel drive power to both the front and rear wheels for use on low traction surfaces, but does so with additional gearing for increased torque multiplication. This mode is only for off-road conditions such as deep sand, steep slopes, or pulling heavy objects.

What does the four-wheel drive warning lamp illuminate for?

When a four-wheel drive or power train fault is present.

What happens when a four-wheel drive system fault is present?

The system can typically remain in whichever mode was selected prior to the fault condition occurring. It does not default to two-wheel drive in all circumstances.

What should you do when the four-wheel drive warning lamp is displayed?

Have your vehicle serviced by an authorized dealer.

What does the “For 4L slow to a stop” message display?

When the driver attempts to shift into four-wheel drive low when traveling at too high of a speed.

What does the “For 4L Shift to N” message display?

When the driver attempts to shift into four-wheel drive low without the transmission in neutral (N).

What does the “For 4L press Clutch” message display?

When the driver attempts to shift into four-wheel drive low without the clutch pedal pressed.

What does the “To exit 4L slow to a stop” message display?

When the driver attempts to shift out of four-wheel drive low when traveling at too high of a speed.

What does the “To Exit 4L Shift to N” message display?

When the driver attempts to shift out of four-wheel drive low without the transmission in neutral (N).

What does the “To exit 4L Press Clutch” message display?

When the driver attempts to shift out of four-wheel drive low without the clutch pedal pressed.

What does the “4×4 Shift in Progress” message display?

When the four-wheel drive system is shifting into and out of two-wheel drive high or between high and low ranges.

What does the “4X4 Temporarily Locked” message display?

When the four-wheel drive system detects a driving condition which temporarily requires greater four-wheel drive performance. The system resumes normal function after the system no longer detects these driving conditions.

What does the “4×4 Temporarily Disabled” message display?

When the four-wheel system detects elevated system temperature and temporarily stops providing power to the front wheels. The system resumes normal function when the system temperature returns to normal.

What does the “4×4 Restored” message display?

When the four-wheel drive system resumes normal function.

What does the “Shift Delayed Drive Forward” message display?

When the transfer case is not able to complete a shift and requires forward motion to complete the shift.

What does the “4×4 OFF” message display?

When the system has become disabled due to mismatched tires or an external fault.

What does the “Neutral Tow Enabled Leave Transmission in Neutral” message display?

When neutral tow mode has been successfully engaged.

What does the “Neutral Tow Disabled” message display?

When neutral tow mode has been successfully disengaged.

What does the “Selected 4×4 Mode Not Available in Current Drive Mode” message display?

When the driver selects a four-wheel drive mode that is disallowed in the currently selected drive mode.

What does the “To Engage 4×4 Slow to 3 MPH” message display?

When the system is unable to engage four-wheel drive high and requires the driver to slow down before attempting to engage.

What does the “To Engage 4×4 Slow to 5 km/h” message display?

When the system is unable to engage four-wheel drive high and requires the driver to slow down before attempting to engage.

What does the “To Engage 4×4 Release Accelerator Pedal” message display?

When the four-wheel drive system requires the accelerator pedal to be released to perform the shift into four-wheel drive mode.

What does the “4×4 Performance Reduced See Manual” message display?

When the system has entered a degraded mode due to mismatched tires.

What is the electronic locking differential?

A device housed in the front or rear axle that, when activated allows both wheels on that axle to turn at the same speed.

When can the electronic locking differential provide additional traction?

Should your vehicle become stuck.

When does the electronic differential automatically disengage?

When the vehicle speed exceeds a set value.

When does the electronic differential automatically reengage?

When the vehicle speed goes below a set value.

When is the electronic locking differential for use?

In mud, rocks, sand, or any off-road condition where you need maximum traction. It is not for use on dry pavement.

What can using the electronic locking differentials on dry pavement cause?

Increased tire wear, noise and vibration or driveline damage.

When is the front electronic locking differential available?

Only in four-wheel drive low (4L).

What does locking the front differential do to your vehicle’s ability to turn?

Reduces your ability to make tight turning maneuvers and creates additional resistance to steering inputs.

What can switching the electronic locking differentials off while turning cause?

Disengagement difficulties.

What should you do if the electronic locking differential has difficulty disengaging?

Release the accelerator pedal and turn the steering wheel back and forth in small increments while maintaining control and following a straight line.

How do you activate the front or rear locking differential?

By pressing the switch on the center switch pack.

What is the maximum engagement speed for the front electronic locking differential?

20 mph (32 km/h).

What is the maximum engagement speed for the rear electronic locking differential?

20 mph (32 km/h).

When do the rear electronic locking differentials automatically engage?

When you select the Deep Snow/Sand, Mud/Ruts, or Rock Crawl G.O.A.T modes.

When can you manually override the automatic engagement of the electronic locking differentials?

By pressing the electronic locking differential switch.

What does it mean if the front or rear indicator in the cluster is amber?

Both wheels of the indicated axle are locked together providing additional traction.

What can cause the electronic locking differential indicator in the cluster to turn from amber to gray while driving?

Your vehicle speed is too high.
The accelerator pedal is too high during an engagement attempt.
Your vehicle is experiencing an anti-lock brake activation.
The left and right wheel speed difference is too high during an engagement attempt.

What can cause the electronic locking differential indicator in the cluster to not illuminate?

The electronic locking differential is not allowed in the current G.O.A.T mode and is accompanied by SELECTED LOCKING DIFFERENTIAL NOT AVAILABLE IN CURRENT Drive Mode in the information display.
The electronic locking differential is not allowed in the current 4×4 mode and is accompanied by SELECTED LOCKING DIFFERENTIAL NOT AVAILABLE IN CURRENT 4×4 MODE in the information display.
The system has malfunctioned and is accompanied by CHECK LOCKING DIFFERENTIAL in the information display.

What does the “Selected Locking Differential Not Available in Current Drive Mode” message mean?

The selected electronic locking differential is not available in current G.O.A.T mode.

What does the “Selected Locking Differential Not Available in Current 4×4 Mode” message mean?

The selected electronic locking differential is not available in your current four-wheel drive mode.

What does the “To Engage Locking Differential Release Accelerator Pedal” message mean?

The selected electronic locking differential requires that you release the accelerator pedal in order to engage.

What does the “Check Locking Differential” message mean?

An electronic locking differential system fault is present.

What conditions affect the electronic locking differential?

Based on G.O.A.T mode selection, the rear electronic locking differential does not engage if your vehicle speed is above 20 mph (32 km/h).
The front electronic locking differential does not engage if your vehicle speed is above 20 mph (32 km/h) in four-wheel drive low (4L).
Based on G.O.A.T mode selection, the electronic locking differential automatically disengages at speeds above 25 mph (41 km/h) and automatically re-engages at speeds below 20 mph (32 km/h).
The electronic locking differential may not engage if you press your accelerator pedal during an engagement attempt. A message may display in the instrument display guiding you to release the accelerator pedal.
In four-wheel drive low (4L), the front electronic locking differential automatically disengages at speeds above 25 mph (41 km/h) and automatically re-engages at speeds below 20 mph (32 km/h).
The AdvanceTrac system has the ability to take over control of the electronic locking differential and disable it during driving maneuvers when necessary.

What can happen if there is a significant difference between the two rear tires or two front tires?

You may have limited electronic locking differential functionality.

What should you do if the electronic locking differential has difficulty disengaging?

Release the accelerator pedal and turn the steering wheel in the opposite direction when rolling.

When should you engage and disengage the electronic locking differential when you mount a spare or mismatched tire on either axle?

At a stop.

What should you do if the brake warning lamp is on?

Have your vehicle checked as soon as possible.

What can driving extended distances with the parking brake engaged cause?

Brake failure and the risk of personal injury.

What should you do to dry the brakes after leaving a car wash or driving from standing water?

Gently press the brake pedal a few times.

When might the stoplamps flash during heavy braking?

Depending on applicable laws and regulations in the country for which your vehicle was originally built.

What might happen after the stoplamps flash?

The hazard warning flashers could also turn on when your vehicle comes to a stop.

What does the anti-lock braking system not eliminate the risk of crash when?

You drive too closely to the vehicle in front of you.
Your vehicle is hydroplaning.
You take corners too fast.
The road surface is poor.

What might happen if the anti-lock braking system activates?

The brake pedal could pulse and travel further.

What should you do if the accelerator pedal becomes stuck or entrapped?

Apply steady and firm pressure to the brake pedal to slow the vehicle and reduce engine power.

What should you do if you experience the accelerator pedal becoming stuck or entrapped condition?

Apply the brakes and bring your vehicle to a safe stop. Move the transmission to park (P), switch the engine off and apply the parking brake. Inspect the accelerator pedal for any interference. If none are found and the condition persists, have your vehicle towed to the nearest authorized dealer.

What should you do if the brake fluid level is below the MIN mark or above the MAX mark on the brake fluid reservoir?

The brake system could be affected.

How do you check the brake fluid level?

Park your vehicle on a level surface.
Look at the brake fluid reservoir to see where the brake fluid level is relative to the MIN and the MAX marks on the reservoir.

What must you do to avoid fluid contamination when checking the brake fluid?

The reservoir cap must remain in place and fully tight, unless you are adding fluid.

What does it mean if the ABS indicator illuminates when you are driving?

This indicates a malfunction. Your vehicle continues to have normal braking without the anti-lock braking system function.

What should you do if the ABS indicator illuminates when you are driving?

See an authorized dealer.

When does the ABS indicator momentarily illuminate?

When you switch the ignition on to confirm the lamp is functional.

What should you do if the ABS indicator does not illuminate when you switch the ignition on, or begins to flash at any time?

Have the system checked by an authorized dealer.

When does the brake indicator momentarily illuminate?

When you switch the ignition on to confirm the lamp is functional.

When else might the brake indicator illuminate?

When you apply the parking brake and the ignition is on.

What should you do if the brake indicator illuminates when your vehicle is moving?

Make sure the parking brake is disengaged. If the parking brake is disengaged, this indicates low brake fluid level or a brake system fault. See an authorized dealer.

What should you do if the brake fluid level is low?

Check the brake system immediately.

What should you do if the “Check Brake System” message is displayed?

Have the system checked as soon as possible.

What does it mean if a metal-to-metal, continuous grinding, or continuous squeal sound is present?

The brake lining could be worn-out.

What should you do if a metal-to-metal, continuous grinding, or continuous squeal sound is present?

Have the system checked by an authorized dealer.

What do the electrical motor sounds when you press on the brake pedal or activate the park brake switch indicate?

Those sounds are the electronic brake booster or the electronic park brake operating.

What is the electric parking brake used for?

To hold your vehicle on slopes and flat roads.

What should you always do when using the parking brake?

Always fully apply the parking brake.

What can driving extended distances with the parking brake applied cause?

Damage to the brake system.

How do you apply the electric parking brake?

Pull the electric parking brake switch.

When does the red warning lamp flash and illuminate when applying the electric parking brake?

The red warning lamp flashes during operation and illuminates when the parking brake is applied.

When can you apply the electric parking brake?

When the ignition is off.

What could happen when the transmission selector is in park (P) when applying the electric parking brake?

The electric parking brake could apply.

How can you use the electric parking brake to slow or stop your vehicle in an emergency?

Pull and hold the electric parking brake switch.

When using the electric parking brake in an emergency, what happens?

The red warning lamp illuminates, a tone sounds and the stoplamps turn on.

When should you not apply the electric parking brake when your vehicle is moving?

Except in an emergency.

What can happen if you repeatedly use the electric parking brake to slow or stop your vehicle?

You could cause damage to the brake system.

How do you manually release the electric parking brake?

Switch the ignition on.
Apply and hold the brake pedal.
Push the electric parking brake switch. The red warning lamp turns off.

How do you pull away on a hill when towing a trailer using the electric parking brake?

Apply and hold the brake pedal.
Pull and hold the electric parking brake switch.
Shift the vehicle into gear.
Apply the accelerator pedal until the engine has developed sufficient torque to prevent your vehicle from rolling down the hill.
Release the switch and pull away in a normal manner.

How do you automatically release the electric parking brake?

Close the driver door.
Shift into gear.
Press the accelerator pedal and pull away in a normal manner.

What happens if the electric parking brake warning tone continues after you have released the parking brake?

This indicates a malfunction.

What should you do if the electric parking brake warning tone continues after you have released the parking brake?

Have your vehicle checked as soon as possible.

What should you do if the vehicle battery has run out of charge and you cannot release the electric parking brake?

Connect a booster battery to the vehicle battery to release the electric parking brake.

What does it mean when the brake system warning lamp illuminates red when you apply the parking brake and your vehicle is on?

The parking brake is applied.

What does it mean if the brake system lamp flashes when the parking brake has been released?

This indicates the parking brake system requires service.

What does it mean when the electric parking brake lamp illuminates yellow?

It indicates a malfunction in the electric parking brake.

What does the “Park Brake Applied” message mean?

The electric park brake is fully applied.

What does the “Park Brake Released” message mean?

The electric park brake is fully released.

What does the “Park Brake System Overheated” message mean?

The electric park brake system has detected a condition where components may have been subject to overheating.

What does the “To Release: Press Brake and Switch” message mean?

The electric parking brake is set and you attempted a manual release without pressing the brake.

What does the “Park Brake Use Switch to Release” message mean?

With the electric parking brake set, you attempted an auto-matic release with no success. Perform a manual release.

What does the “Release Park Brake” message mean?

The electric parking brake is set and your vehicle speed exceeds 3 mph (5 km/h). Release the parking brake before continued driving.

What does the “Park Brake Not Applied” message mean?

The electric parking brake is not fully applied.

What does the “Park Brake Not Released” message mean?

The electric parking brake is not fully released.

What does the “Park Brake Maintenance Mode” message mean?

The electric parking brake system has been put into a special mode that is used to allow service of the rear brakes.

What does the “Park Brake Limited Function Service Required” message mean?

The electric parking brake system has detected a condition that requires service. Some functionality may still be available.

What does the “Park Brake Malfunction Service Now” message mean?

The electric parking brake system has detected a condition that requires service.

How does Adaptive Cruise Control work?

Adaptive Cruise Control uses a windshield-mounted camera to view the road, but optimal performance may not occur if the camera is blocked, visibility or lighting is poor, or there are bad weather conditions.

How do you switch Adaptive Cruise Control on?

Press the button on the steering wheel to activate the system. When activated, the set speed is equal to the current vehicle speed. If the speed is too low, or other conditions are not correct for activation, the system enters standby mode. The minimum set speed is 15 mph or 20 km/h. The indicator, current gap setting, and set speed will appear in the instrument cluster display.

How do you switch Adaptive Cruise Control off?

Press the button when the system is in standby mode, or switch the ignition off. When the system is switched off, the set speed clears.

When might Adaptive Cruise Control automatically cancel or deactivate?

The system may cancel if the tires lose traction, the parking brake is applied, or the vehicle speed falls significantly below 15 mph or 20 km/h. The system may also turn off or prevent activation if the vehicle has a blocked sensor, the brake temperature is too high, or there is a failure in the system or a related system.

How do you set the Adaptive Cruise Control speed?

Drive to the desired speed, then press the button to set the current speed. Take your foot off the accelerator pedal. The indicator, current gap setting, and set speed will appear in the information display. A vehicle image will illuminate if there is a vehicle detected in front of you. When adaptive cruise control is active, the speedometer may vary slightly from the set speed displayed in the information display.

How do you manually change the set speed of the Adaptive Cruise Control?

Press and release the button to increase the set speed in small increments, or press and hold the button to increase the set speed in large increments. Release the button when the displayed set speed is equal to the desired speed. To decrease the set speed, press and release the button to decrease the set speed in small increments, or press and hold the button to decrease the set speed in large increments. Release the button when the displayed set speed is equal to your desired speed. You can also press the accelerator or brake pedal until you reach the speed you prefer, then press the button to select the current speed as the set speed. The system may apply the brakes to slow the vehicle to the new set speed. The set speed displays continuously in the information display when the system is active.

How do you set the Adaptive Cruise Control gap?

A minimum vehicle speed of 15 mph or 20 km/h must be met before you can set the gap. Press the button to cycle through the four gap settings. The selected gap appears in the instrument cluster display. The gap setting is time dependent, so the distance adjusts with the vehicle speed. It is the driver’s responsibility to select a gap appropriate to the driving conditions.

What are the Adaptive Cruise Control gap settings?

The following table shows the gap settings:

Gap Setting	Graphic Display, Bars Indicated	Distance Between Vehicles
Sport	1	Closest
Normal	2	Close
Normal	3	Medium
Comfort	4	Far

Each time you switch the system on, it selects the last chosen gap setting.

How does Adaptive Cruise Control respond when following a vehicle?

When a vehicle ahead enters the same lane or a slower vehicle is ahead in the same lane, the vehicle speed adjusts to maintain the gap setting. When following a vehicle and switching on a turn signal lamp, adaptive cruise control may provide a small, temporary acceleration to help you pass. The vehicle maintains a consistent gap from the vehicle ahead until:

The vehicle in front accelerates to a speed above the set speed.
The vehicle in front moves out of the lane.
A new gap distance is set.

The system applies the brakes to slow down the vehicle to maintain a safe gap from the vehicle in front. The system only applies limited braking. You can override the system by applying the brakes. The brakes may emit noise when applied by the system. If the system determines that its maximum braking level is not sufficient, an audible warning sounds, a message appears in the instrument cluster display, and an indicator flashes when the system continues to brake. Take immediate action.

How do you cancel the set speed of the Adaptive Cruise Control?

Press the button or tap the brake pedal. The set speed does not erase.

How do you resume the set speed of the Adaptive Cruise Control?

Press the button. The vehicle speed returns to the previously set speed and gap setting. The set speed displays continuously in the information display when the system is active. Only use resume if you are aware of the set speed and intend to return to it.

How do you override the set speed of the Adaptive Cruise Control?

When you press the accelerator pedal, you override the set speed and gap distance. Use the accelerator pedal to intentionally exceed the set speed limit. When you override the system, the green indicator illuminates and the vehicle icon does not appear in the instrument cluster display. The system resumes operation when you release the accelerator pedal. The vehicle speed decreases to the set speed, or a lower speed if following a slower vehicle. If you override the system by pressing the accelerator pedal, it does not automatically apply the brakes to maintain a gap from any vehicle ahead.

What do the Adaptive Cruise Control indicators mean?

The indicator illuminates when you switch adaptive cruise control on. The color of the indicator changes to indicate the system status. White indicates the system is on but inactive, and green indicates that you set the speed and the system is active.

How do you switch from Adaptive Cruise Control to normal Cruise Control?

Use the touchscreen to select the following: 1. Select Settings. 2. Select Driver Assist. 3. Select Cruise Control. 4. Select Normal. Normal cruise control will not brake when the vehicle is approaching slower vehicles. Always be aware of which mode is selected and apply the brakes when necessary.

What happens when you select normal cruise control?

The cruise control indicator replaces the adaptive cruise control indicator. The gap setting does not display, and the system does not respond to lead vehicles. Automatic braking remains active to maintain set speed. The system remembers the last setting when you start your vehicle.

What are some Adaptive Cruise Control troubleshooting messages?

The following are some troubleshooting messages:

Action	Message
A malfunction is preventing the adaptive cruise from engaging.	Adaptive Cruise Malfunction
Front Sensor Not Aligned	Contact an authorized dealer to have the radar checked for proper coverage and operation.
Conditions exist preventing the system from being available.	Adaptive Cruise Not Available
You have a blocked radar because of poor radar visibility due to inclement weather or ice, mud, or water in front of the radar.	Adaptive Cruise Not Available Sensor Blocked See Manual
You have selected normal cruise control. The system does not brake or react to traffic.	Normal Cruise Active Adaptive Braking Off
Displays when the adaptive cruise control is going to cancel and you must take control.	Adaptive Cruise – Driver Resume Control
Displays when the vehicle speed is too slow to activate the adaptive cruise control and there is no lead vehicle in range.	Adaptive Cruise Speed Too Low to Activate

What are G.O.A.T. modes?

Your vehicle has several Goes Over Any-type of Terrain (G.O.A.T.) modes that you can select for different driving conditions. Depending on the mode selected, the system adjusts various vehicle settings.

How do G.O.A.T. modes work?

Each selectable mode changes various electronic and mechanical settings within your vehicle to tailor its performance and driving characteristics to on-road or off-road driving conditions. The system may alter steering feel and effort, traction control, stability control, chassis controls, powertrain response, transmission shift points, four-wheel driveline setting, exhaust noise level and suspension damping to predetermined settings, depending upon the mode that you select. The system reverts to the normal mode each time the vehicle is started. At startup, the system also displays a prompt on the instrument cluster display that gives you the option to return to the previously selected drive mode during the last ignition cycle. If you select yes, the system returns to the last selected drive mode and the default driveline settings associated with that mode. If you select no or do not make a selection within a short time, the system remains in normal mode and the driveline settings remain the same as selected in the prior ignition cycle. Your vehicle has diagnostic checks that continuously monitor all systems for proper operation. If a mode is unavailable due to a system fault, the vehicle defaults to normal mode and the driveline remains in the four-wheel drive setting that you last selected prior to the system fault.

How do you select a G.O.A.T. mode?

To select a mode, use the console mounted controller. Mode changes will not be available when the ignition is off or when the engine is not running. Button icons may vary.

What happens to the brake over accelerator feature when in off-road modes?

To optimize off-road driving performance, the system disables the brake over accelerator feature when in off-road modes, including mud/ruts, sand, baja and rock crawl modes. A message displays in the instrument cluster when you select an off-road mode. Brake over accelerator enables when an off-road mode is exited or during the next key cycle. Return to on-road modes, normal, eco, sport or slippery, when driving on regular roads.

What is Baja mode for?

Baja mode is for high speed off-road driving. It optimizes the throttle control for better response and torque delivery. Four-wheel drive high (4H) is the default four-wheel drive mode. Four-wheel drive auto (4A) is not selectable in baja mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is available at any speed in all selectable four-wheel drive modes. The stabilizer bar disconnect is available in four-wheel drive high (4H) or four-wheel drive low (4L). When using Baja mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear.

What is Eco mode for?

Eco mode is for efficient driving. This mode helps deliver maximum fuel efficiency and helps to increase driving range. Two-wheel drive high (2H) is the default four-wheel drive mode. Four-wheel drive low (4L) is not selectable in eco mode. The front electronic locking differential is not available in eco mode. The rear electronic locking differential is available below 25 mph (40 km/h). The stabilizer bar disconnect is not available in eco mode.

What is Mud/Ruts mode for?

Mud/Ruts mode is for off-road driving. This mode enhances vehicle performance to traverse muddy, rutted, or uneven terrains. Four-wheel drive high (4H) is the default four-wheel drive mode. Four-wheel drive low (4L) is selectable in mud/rut mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is engaged when in mud/ruts mode and is available at any speed in all selectable four-wheel drive modes. The stabilizer bar disconnect is available in four-wheel drive high (4H) or four-wheel drive low (4L). When using Mud/Ruts mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear.

What is Normal mode for?

Normal mode is for everyday driving. This mode is the perfect balance of excitement, comfort, and convenience. This is the default mode after each ignition cycle; the driveline settings remain the same prior to the ignition cycle. Two-wheel drive high (2H) is the default four-wheel drive mode. All four-wheel drive modes are selectable when in normal mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is available below 25 mph (40 km/h). The rear electronic locking differential is available at any speed when in four-wheel drive low (4L). The stabilizer bar disconnect is available in four-wheel drive high (4H) or four-wheel drive low (4L).

What is Rock Crawl mode for?

Rock Crawl mode is for off-road driving and optimum rock-climbing ability. This mode optimizes the throttle and transmission response to provide additional control of your vehicle. Four-wheel drive low (4L) is the only driveline configuration available in rock crawl; the system prompts you to put your vehicle into four-wheel drive low (4L) upon selection. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is engaged when in rock crawl mode and is available at any speed. The stabilizer bar disconnects when in rock crawl mode. When using rock crawl mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear.

What is Sand mode for?

Sand mode is for off-road driving on soft, dry sand or deep snow. This mode may help get your vehicle unstuck from deep snow or sand. Four-wheel drive high (4H) is the default four-wheel drive mode. Four-wheel drive low (4L) is selectable in sand mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is engaged when in sand mode and is available at any speed in all selectable four-wheel drive modes. The stabilizer bar disconnect is available in four-wheel drive high (4H) or four-wheel drive low (4L). The front camera system switches on when you are in sand mode and your speed is less than 15 mph (24 km/h). If you exceed 15 mph (24 km/h), the camera shuts off until your vehicle speed is below 12 mph (20 km/h). When using Sand mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear. Sand mode is not intended for use on firm, slippery surfaces, such as paved roads covered with snow or ice. For slippery, firm surfaces, use slippery mode.

What is Slippery mode for?

Slippery mode is for less than ideal road conditions; this mode can be used for crossing terrain where a firm surface is covered with loose or slippery material, such as snow or ice. Slippery mode lowers throttle response and optimizes shifting for slippery surfaces.

There are two slippery modes: 4×4 with part-time engagement and advanced 4×4 with 4A mode.

For the 4×4 with part-time engagement mode: Four-wheel drive high (4H) is the default four-wheel drive mode. All four-wheel drive modes are selectable in slippery mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is available below 25 mph (40 km/h). The rear electronic locking differential is available at any speed when in four-wheel drive low (4L). The stabilizer bar disconnect is not available in slippery mode. When using Slippery mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear.

For the advanced 4×4 with 4A mode: Four-wheel drive auto (4A) is the default four-wheel drive mode. Two-wheel drive high (2H) is not selectable in slippery mode. The front electronic locking differential is available below 25 mph (40 km/h) when in four-wheel drive low (4L). The rear electronic locking differential is available below 25 mph (40 km/h). The rear electronic locking differential is available at any speed when in four-wheel drive low (4L). The stabilizer bar disconnect is not available in slippery mode. When using Slippery mode on dry/hard pavement, your vehicle could experience vibration, driveline bind up, damage, and potential excessive tire and vehicle wear.

What is Sport mode for?

Sport mode is for sporty driving with improved performance handling and response. This mode increases accelerator pedal response and provides a sportier steering feel. The powertrain system holds onto lower gears longer, helping the vehicle accelerate faster.

There are two sport modes: 4×4 with part-time engagement and advanced 4×4 with 4A mode.

For the 4×4 with part-time engagement mode: Two-wheel drive high (2H) is the default four-wheel drive mode. Four-wheel drive low (4L) is not selectable in sport mode. The front electronic locking differential is not available in sport mode. The rear electronic locking differential is available below 25 mph (40 km/h). The stabilizer bar disconnect is not available in sport mode.

For the advanced 4×4 with 4A mode: Four-wheel drive auto (4A) is the default four-wheel drive mode. Four-wheel drive low (4L) is not selectable in sport mode. The front electronic locking differential is not available in sport mode. The rear electronic locking differential is available below 25 mph (40 km/h). The stabilizer bar disconnect is not available in sport mode.

What do the G.O.A.T. mode control warning lamps indicate?

Some drive modes reduce traction and stability control performance, and the indicator illuminates in the instrument cluster.

What are some G.O.A.T. mode control information messages?

The following are some G.O.A.T. mode control information messages:

Details	Message
Displays when the system switches to normal mode to support towing performance.	Changing to Normal Drive Mode for Improved Towing Performance
Displays when you select a drive mode that is not available.	Select a different drive mode.Drive Mode Not Available
Displays when you select a drive mode that is not available. Check the four-wheel drive mode, electronic locking differential and stabilizer bar before selecting a drive mode.	Drive Mode Preconditions Not Met
Displays when you select a drive mode that is not available. Have the system checked.	Drive Mode Selection Reduced due to System Fault
Displays when you select an off-road drive mode.	Off-Road Use Only
Displays when you select a four-wheel drive mode that is not available in the current drive mode.	Select an available four-wheel drive mode.Selected 4×4 Mode Not Available in Current Drive Mode
Displays when you select an electronic locking differential that is not available in the current drive mode.	Select an available electric locking differential.Selected Locking Differential Not Available in Current Drive Mode
Displays when you attempt to disconnect the stabilizer bar in the current drive mode.	Select a different drive mode to disconnect the stabilizer bar.Sta-Bar Disconnect Not Available In Selected Drive Mode

Why does the system default to normal mode?

If a mode is unavailable due to a system fault, normal mode is selected, and the driveline settings remain the same as prior to the system fault.

What is the Lane Keeping System?

The lane keeping system alerts you by providing temporary steering assistance or steering wheel vibration when it detects an unintended lane departure.

How does the Lane Keeping System work?

The lane keeping system uses a forward-looking camera mounted on the windshield to monitor vehicle movement within the travel lane. When the camera detects a drift out of the travel lane, the lane keeping system alerts the driver by vibrating the steering wheel, or aids the driver by providing a small steering input to move the vehicle back into the travel lane. The driver can select one of three modes: Alert, Aid, or Alert + Aid.

What are some precautions for using the Lane Keeping System?

You are responsible for controlling your vehicle at all times. The system is designed to be an aid and does not relieve you of your responsibility to drive with due care and attention. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury, or death.
The system will not operate if the sensor cannot track the road lane markings.
The sensor may incorrectly track lane markings as other structures or objects. This can result in a false or missed warning.
In cold and severe weather conditions, the system may not function. Rain, snow, and spray can all limit sensor performance.
The system may not operate properly if the sensor is blocked. Keep the windshield free from obstruction.
If damage occurs in the immediate area surrounding the sensor, have your vehicle checked as soon as possible.
The system may not correctly operate if your vehicle is fitted with a suspension kit not approved.
Large contrasts in outside lighting can limit sensor performance.

What are some limitations of the Lane Keeping System?

The lane keeping system only operates when the vehicle speed is greater than 40 mph (64 km/h). The system works when the camera can detect at least one lane marking. The lane keeping system may not correctly operate in any of the following conditions:

The lane keeping system does not detect at least one lane marking.
You switch the turn signal on.
You apply direct steering, accelerate fast, or brake hard.
The vehicle speed is less than 40 mph (64 km/h).
The anti-lock brake, stability control, or traction control system activates.
The lane is too narrow.
Something is obscuring the camera or it is unable to detect the lane markings due to environment, traffic, or vehicle conditions.

The lane keeping system may not correct lane positioning in any of the following conditions:

High winds.
Uneven road surfaces.
Heavy or uneven loads.
Incorrect tire pressure.

How do you switch the Lane Keeping System on and off?

To activate the lane keeping system, press the button on the steering wheel. To deactivate the lane keeping system, press the button again. When switching the system on or off, a message appears in the information and entertainment display to show the status. The system stores the on or off setting until manually changed, unless it detects a MyKey™. If the system detects a MyKey™, it defaults to the last setting for that MyKey™. If the system detects a MyKey™, pressing the button does not affect the on or off status of the system. You can only change the mode and intensity settings.

How do you switch the Lane Keeping System mode?

The lane keeping system has different settings that you can view or adjust using the information display. The system stores the last known selection for each of these settings. You do not need to readjust your settings each time you switch on the system. To change the lane keeping system mode, use the touchscreen: 1. Select Driver Assistance. 2. Select Lane Keeping System. 3. Select Mode. 4. Select a setting. The system remembers the last setting when you start your vehicle. If the system detects a MyKey™, the mode is set to alert.

What is Alert mode?

Alert mode vibrates the steering wheel when it detects an unintended lane departure.

How does Alert mode work?

When in alert mode, the lane keeping system alerts you by vibrating the steering wheel. The intensity of the vibration is set through the lane keeping system menu.

How do you adjust the steering wheel vibration intensity for Alert mode?

To change the steering wheel vibration intensity, use the touchscreen: 1. Select Driver Assistance. 2. Select Lane Keeping System. 3. Select Intensity. 4. Select a setting.

What is Aid mode?

Aid mode provides temporary steering assistance toward the center of the lane.

How does Aid mode work?

The lane keeping system aids you when an unintentional lane departure occurs. The system provides a small steering input to move the vehicle towards the center of the lane.

What is Alert and Aid mode?

Alert and aid mode uses multiple features to keep you in your lane. The system first provides a small steering input to bring your vehicle back towards the center of the lane. If your vehicle moves too far out of the center of the lane, the system alerts you with vibration in the steering wheel.

How does Alert and Aid mode work?

The lane keeping system detects a lane departure and provides aid when the vehicle enters zone B and applies the additional alert warning if zone A is entered.

What do the Lane Keeping System indicators mean?

If you switch the lane keeping system on, a graphic with lane markings appears in the information display. When you switch the system off, the lane marking graphics do not display. The overhead vehicle graphic may still display if adaptive cruise control is enabled. While the lane keeping system is on, the color of the lane markings change to indicate the system status:

Color	Indicates
Red	Indicates that the system is providing or has just provided a lane keeping alert warning.
Yellow	Indicates that the system is providing or has just provided a lane keeping aid intervention.
Green	Indicates that the system is available or ready to provide a warning or intervention on the indicated side.
Gray	Indicates that the system is temporarily unavailable to provide a warning or intervention on the indicated side.

What are some Lane Keeping System troubleshooting messages?

The following are some Lane Keeping System troubleshooting messages:

Action	Message
The system has malfunctioned. Have your vehicle checked as soon as possible.	Lane Keeping Sys. Malfunction Service Required
The system has detected a condition that has caused the system to be temporarily unavailable.	Front Camera Temporarily Not Available
The system has detected a condition that requires you to clean the windshield in order for it to operate properly.	Front Camera Low Visibility Clean Screen
The system has malfunctioned. Have your vehicle checked as soon as possible.	Front Camera Malfunction Service Required
The system requests that you keep your hands on the steering wheel.	Keep Hands on Steering Wheel

Why is the Lane Keeping System feature not available (lane markings are gray) when I can see the lane markings on the road?

Your vehicle speed is less than 40 mph (65 km/h).
The sun is shining directly into the camera lens.
A quick intentional lane change has occurred.
Your vehicle stays too close to the lane markings for an extended interval of time.
You are driving at high speeds in curves.
The last alert warning or aid intervention occurred a short time ago.
There are ambiguous lane markings, for example, in construction zones.
There is a rapid transition from light to dark, or from dark to light.
There is a sudden offset in lane markings.
ABS or AdvanceTrac™ is active.
There is a camera blockage due to dirt, grime, fog, frost, or water on the windshield.
You are driving too close to the vehicle in front of you.
You are transitioning between no lane markings to lane markings, or vice versa.
There is standing water on the road.
There are faint lane markings, for example, partial yellow lane markings on concrete roads.
The lane width is too narrow or too wide.
You have not calibrated the camera after a windshield replacement.
You are driving on tight or uneven roads.

Why does the vehicle not come back toward the middle of the lane, as expected, in the Aid, or Aid + Alert mode?

High cross winds are present.
There is a large road crown.
There are rough roads, grooves, or shoulder drop-offs.
There is heavy, uneven loading of the vehicle, or improper tire inflation pressure.
You changed the tires or modified the suspension.

What is the Blind Spot Information System?

The blind spot information system detects vehicles that may have entered the blind spot zone.

How does the Blind Spot Information System work?

The blind spot information system uses sensors on both sides of your vehicle, detecting rearward from the exterior mirrors to approximately 13 ft (4 m) beyond the rear bumper. The detection area extends to approximately 59 ft (18 m) beyond the rear bumper when the vehicle speed is greater than 30 mph (48 km/h) to alert you of faster approaching vehicles.

What are some precautions for using the Blind Spot Information System?

Do not use the blind spot information system as a replacement for using the interior and exterior mirrors or looking over your shoulder before changing lanes. The blind spot information system is not a replacement for careful driving.
The system may not operate properly during severe weather conditions, for example snow, ice, heavy rain and spray. Always drive with due care and attention. Failure to take care may result in a crash.
The blind spot information system does not prevent contact with other vehicles. It does not detect parked vehicles, pedestrians, animals, or other infrastructure.

What are some limitations of the Blind Spot Information System?

The blind spot information system does not operate in park (P) or reverse ®. The system may not alert you if a vehicle quickly passes through the detection zone.

What are the Blind Spot Information System requirements for manual transmissions?

The blind spot information system turns on when all the following occur:

You start your vehicle.
You shift into neutral or any forward gear.
The vehicle speed is greater than 6 mph (10 km/h).

What are the Blind Spot Information System requirements for automatic transmissions?

The blind spot information system turns on when all the following occur:

You start your vehicle.
You shift into drive (D).
The vehicle speed is greater than 6 mph (10 km/h).

How do you switch the Blind Spot Information System on and off?

To switch the blind spot information system on or off, use the touchscreen: 1. Press Features on the touchscreen. 2. Press Driver Assistance. 3. Press Blind Spot Information System. 4. Switch the feature on or off. When you switch blind spot information system off, a warning lamp illuminates and a message displays. When you switch the system on or off, the alert indicators flash twice. The system remembers the last setting when you start your vehicle. To permanently switch the system off, contact an authorized dealer.

Where are the Blind Spot Information System sensors located?

The sensors are behind the rear fascia panel. Keep the sensors free from snow, ice, and large accumulations of dirt. Do not cover the sensors with bumper stickers, repair compound, or other objects. Bike and cargo racks could cause false alerts due to obstruction of the sensor. It is recommended to switch the feature off when using a bike or cargo rack. Blocked sensors may affect system accuracy. If the sensors become blocked, a message appears in the instrument cluster display. The alert indicators illuminate, but the system does not alert you.

What do the Blind Spot Information System indicators mean?

When the blind spot information system detects a vehicle, an alert indicator illuminates in the exterior mirror on the side the approaching vehicle is coming from. If you turn the turn signal on for that side of your vehicle, the alert indicator flashes.

What are some Blind Spot Information System troubleshooting messages?

The following are some Blind Spot Information System troubleshooting messages:

Action	Message
A fault with the system has occurred. Have your vehicle checked as soon as possible.	Blind Spot System Fault
Something is blocking the sensors. Clean the sensors.	Blind Spot Not Available Sensor Blocked See Manual
The system automatically turns off and displays this message when you connect a trailer to the vehicle that does not have a trailer blind spot system or when you switch the trailer blind spot system off through the touchscreen.	Blind Spot Alert Deactivated Trailer Attached

What is Cross Traffic Alert?

The system alerts you of vehicles approaching from the sides behind your vehicle when you shift into reverse ®.

How do I use the front and rear differential lock?

When engaged, the front and rear differential lock provides additional traction to your vehicle by forcing either the two rear wheels or two front wheels to turn at the same speed. You can activate and deactivate the front and rear differential lock on the fly within the operating speed range.

How does Trail Control work?

The system works in a similar manner to cruise control in off-road conditions. Trail Control provides you the ability to maneuver the vehicle without using the throttle and brake pedals. Trail Control allows you to set a speed between 1 mph (1.6 km/h) to 14 mph (23 km/h) in a forward motion and 1 mph (1.6 km/h) to 5 mph (8 km/h) in reverse. The system controls acceleration and braking in difficult off-road environments, which allows you to focus on steering.

What are the performance benefits of using Trail Control?

Manages wheel slip to maximize traction.
Removes the need for you to use both feet when driving in off-road situations.
Provides braking to maximize traction in descents.
Gives you confidence in difficult environments.

How does Trail One Pedal Drive work?

Trail one pedal drive coordinates propulsive and braking torque through your application of the accelerator pedal to simulate a two footed driving technique. Use this when driving over large obstacles, such as rocks or logs, to help maintain a constant vehicle speed. In 4H, the system offers lift pedal braking and auto hill hold functionality. Trail one pedal drive is only available when the vehicle is in 4H or 4L.

How does Trail Turn Assist work?

The feature reduces the turn radius of the vehicle on off-road surfaces. The system reduces driver effort to negotiate difficult off-road terrain by allowing the vehicle to make a tight turn in a single maneuver that might otherwise require a three point turn. Trail turn assist is only available when the vehicle is in 4H or 4L. Trail turn assist cannot activate if the rear differential is locked.

What are rock rails and what are they used for?

Rock rails protect the rocker and body side from damage and provide a sliding surface to allow the vehicle to cross boulders and rock ledges. Rock rails also can act as a pivot point to sharply turn the vehicle in tight spaces with high walls or rocks present.

What should I do after driving my vehicle off-road?

After off-road use, before returning to the road, check the wheels and tires for damage. Off-road use may cause damage to your wheels and tires that can lead to tire failure, loss of vehicle control, serious injury or death. Check for damage to the wheels, chassis and underbody. Inspect the underbody of your vehicle by checking tires, body structure, steering, suspension, and exhaust system for damage. Inspect the tires for any cuts in the tread or sidewall area. Also inspect the sidewall for any bulge indicating damage to the tire. Make sure the tires are inflated to proper tire pressure as indicated on the tire placard. Check the radiator for mud and debris and clean as needed. Check that the air filter is clean and dry. Remove accumulations of plants or brush. Make sure the grille and radiator are clear of any obstructions that may affect cooling. After extended operation in mud, sand, water, or similar dirty conditions, inspect the wipers and washers to make sure they are working. Check wipers for debris or anything that may scratch the windshield. If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. If you have removed the impacted material from the wheels and your vehicle still has a vibration check your vehicle for damage or see an authorized dealer. Inspect the exhaust system for damage or looseness. Make sure that the brakes are in proper working order and free of any mud, stones and debris, which can become trapped around the brake rotor, backing plate and caliper. Inspect the wheels for dents, cracks, or other damage. Inspect undercarriage fasteners. If any are loose or damaged, tighten or replace ensuring that the proper torque specification is used. Inspect for torn or punctured boots on ball joints, half shafts, steering gears. Refit the front license plate if removed previously.

What are some cold weather precautions?

The functional operation of some components and systems can be affected at temperatures below approximately -13°F (-25°C).

What should I avoid doing during the break-in period of my vehicle?

For the first 1,000 mi (1,600 km), avoid driving at high speeds, heavy braking, aggressive shifting or using your vehicle to tow. During this time, your vehicle may exhibit some unusual driving characteristics.

How can I drive more economically?

The following helps to improve fuel consumption:

Drive smoothly, accelerate gently and anticipate the road ahead to avoid heavy braking.
Regularly check your tire pressures and make sure that they are inflated to the correct pressure.
Follow the recommended maintenance schedule and carry out the recommended checks.
Plan your journey and check the traffic before you set off. It is more efficient to combine errands into a single trip whenever possible.
Avoid idling the engine in cold weather or for extended periods. Start the engine only when you are ready to set off.
Do not carry unnecessary weight in your vehicle as extra weight wastes fuel.
Do not add unnecessary accessories to the exterior of your vehicle, for example running boards. If you use a roof rack, remember to fold it down or remove it when not in use.
Do not shift into neutral when you are braking or when your vehicle is slowing down.
Shut all windows when driving at high speeds.
Switch off all electric systems when not in use, for example air conditioning. Make sure that you unplug any accessories from the auxiliary power points when not in use.

What are the warnings related to floor mats?

Use a floor mat designed to fit the footwell of your vehicle that does not obstruct the pedal area. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
Secure the floor mat to both retention devices so that it cannot slip out of position and interfere with the pedals. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Do not place additional floor mats or any other covering on top of the original floor mats. This could result in the floor mat interfering with the operation of the pedals. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Always make sure that objects cannot fall into the driver foot well while your vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control.

How do I install floor mats with eyelets?

To install floor mats that have eyelets, position the floor mat eyelet over the retention post and press down to lock in position. Repeat for all eyelets on the floor mat. To remove the floor mats, reverse the installation procedure. Regularly check the floor mats to make sure they are secure.

What roadside assistance services are available in the United States?

Roadside Assistance covers:

A flat tire change with a good spare (except vehicles supplied with a tire inflation kit).
Battery jump start.
Lock-out assistance (key replacement cost is the customer’s responsibility).
Fuel delivery — independent service contractors, if not prohibited by state, local or municipal law, shall deliver up to 2 gal (8 L) of gasoline or 5 gal (20 L) of diesel fuel to a disabled vehicle. Roadside assistance limits fuel delivery service to two no-charge occurrences within a 12-month period.
Winch out — available within 100 ft (30 m) of a paved or county maintained road, no recoveries.
Towing — independent service contractors, if not prohibited by state, local or municipal law, shall tow Ford eligible vehicles to an authorized dealer within 35 mi (56 km) of the disablement location or to the nearest authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km).
Roadside Assistance includes up to $200 for a towed trailer if the disabled eligible vehicle requires service at the nearest authorized dealer. If the towing vehicle is operational but the trailer is not, then the trailer does not qualify for any roadside services.

How do I use roadside assistance in the United States?

Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is in the Owner’s Manual kit. United States vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company reimburses a reasonable amount for towing to the nearest dealership within 35 mi (56 km). To obtain reimbursement information, United States vehicle customers call 1-800-241-3673. Customers need to submit their original receipts.

How do I use roadside assistance in Canada?

To fully assist you should you have a vehicle concern, Ford Motor Company of Canada, Limited offers a complimentary roadside assistance program. This program is eligible within Canada or the continental United States. The service is available 24 hours a day, seven days a week. This program is separate from the New Vehicle Limited Warranty, but the coverage is concurrent with the powertrain coverage period of your vehicle. Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please call us in Canada at 1-800-665-2006, or visit our website at http://www.ford.ca.

How do I switch the hazard flashers on and off?

The hazard flasher button is on the instrument panel. Press the button to switch the hazard flashers on if your vehicle is creating a safety hazard for other road users. When you switch the hazard flashers on, all front and rear direction indicators flash. The hazard flashers operate when the ignition is in any position, or if the key is not in the ignition. The battery loses charge and could have insufficient power to restart your vehicle. Press the button again to switch them off.

What are the precautions for jump starting a vehicle?

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide correct ventilation.
Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.
Use only adequately sized cables with insulated clamps.
Make sure that the cables are clear of any moving parts and fuel delivery system parts.
Connect batteries with only the same nominal voltage.
If the engine is running while the hood is open, stay clear of moving engine components. Failure to follow this warning could result in serious personal injury or death.
Do not attempt to push-start an automatic transmission vehicle. This could cause transmission damage.
Do not disconnect the battery of the disabled vehicle. This could damage your vehicle’s electrical system.

How do I prepare my vehicle for jump starting?

Use only a 12 volt supply to start your vehicle. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch.

How do I connect the jumper cables?

Pull the red plastic boot backward. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery.
Connect the other end of the positive (+) jumper cable to the positive (+) terminal of the booster vehicle battery.
Connect the negative (-) jumper cable to the negative (-) terminal of the booster vehicle battery.
Make the final connection of the negative (-) jumper cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and fuel injection system, or connect the negative (-) jumper cable to a ground connection point if available. If you are using a jump pack or booster box, follow the manufacturer’s instructions.

How do I start the engine of the disabled vehicle after connecting the jumper cables?

Start the engine of the booster vehicle and moderately rev the engine, or gently press the accelerator to keep the engine speed between 2000 and 3000 RPM, as shown in your tachometer.
Start the engine of the disabled vehicle.
Once you start the disabled vehicle, run both vehicle engines for an additional three minutes before disconnecting the jumper cables.

How do I remove the jumper cables?

Remove the jumper cables in the reverse order that they were connected. Do not switch the headlamps on when disconnecting the cables. The peak voltage could blow the bulbs.

What is the Post-Crash Alert System?

The system helps draw attention to your vehicle in the event of a serious impact.

How does the Post-Crash Alert System work?

The system is designed to turn the hazard flashers on and to intermittently sound the horn in the event of a serious impact that deploys an airbag or the seatbelt pretensioners.

What are the limitations of the Post-Crash Alert System?

Depending on applicable laws in the country your vehicle was built for, the horn does not sound in the event of a serious impact.

How do I switch the Post-Crash Alert System off?

Press the hazard flasher switch or the unlock button on the remote control to switch the system off. The alert turns off when the vehicle battery runs out of charge.

How does Post Impact Braking work?

In the event of a moderate to severe crash, the braking system reduces the vehicle’s speed in order to prevent or reduce the impact of a potential secondary crash.

What are the limitations of Post Impact Braking?

Post impact braking does not activate if any of the following occur:

The anti-lock braking system is damaged during the collision.
Electronic stability control is disabled.

How do I override Post Impact Braking?

You can override post impact braking by pressing the brake or accelerator pedal.

What does the Post Impact Braking indicator look like?

It flashes when a post impact braking event is occurring.

What is Automatic Crash Shutoff?

The automatic crash shutoff is designed to stop the fuel going to the engine in the event of a moderate or severe crash. Not every impact causes a shutoff.

What are the precautions related to Automatic Crash Shutoff?

If your vehicle has been involved in a crash, have the fuel system checked. Failure to follow this instruction could result in fire, personal injury or death.

How do I re-enable my vehicle after Automatic Crash Shutoff?

Switch the ignition off.
Attempt to start your vehicle.
Switch the ignition off.
Attempt to start your vehicle. If your vehicle does not start after the third attempt, have your vehicle checked as soon as possible.

What are the warnings related to using recovery hooks?

Using recovery hooks is dangerous and should only be done by a person familiar with proper vehicle recovery safety practices. Improper use of recovery hooks may cause hook failure or separation from the vehicle and could result in serious injury or death.
Slowly remove the slack from the recovery strap prior to pulling. Failure to do so can introduce significantly higher loads which can cause the recovery hooks to break off, or the recovery strap to fail which can cause serious injury or death.
Never link two straps together with a clevis pin. These heavy metal objects could become projectiles if the strap breaks and can cause serious injury or death.

What are the guidelines for using recovery hooks?

Do not apply a load to the recovery hooks that is greater than the gross vehicle weight rating of your vehicle.
Make sure all attaching points are secure and capable of withstanding the applied load.
Do not use chains, cables or tow straps with metal hook ends.
Only use recovery straps that have a minimum breaking strength two to three times the gross vehicle weight of the stuck vehicle.
Make sure the recovery strap is in good condition and free of visible cuts, tears or damage.
Use a damper device such as a tarp, heavy blanket or piece of carpet, and place it over the recovery strap to help absorb the energy in the event the strap breaks.
Make sure the stuck vehicle is not loaded heavier than its gross vehicle weight rating specified on the certification label.
Align the tow vehicle and stuck vehicle in a straight line, within 10 degrees.
Keep bystanders to the sides of the vehicle, at a distance of at least twice the length of the recovery strap. This helps avoid injury from the hazard of a recovery hook or strap breaking, or a vehicle lurching into their path.

What should I do if I need to tow my vehicle?

If you need to tow your vehicle, contact a professional towing service or your roadside assistance service provider. Your manufacturer produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures. All-wheel or four-wheel drive vehicles require that all wheels be off the ground using a wheel lift and dollies or flatbed equipment. This prevents damage to the transmission and drive system.

What precautions should I take when towing my vehicle?

Use the following guidelines when towing your vehicle. Failure to follow this instruction could result in vehicle damage not covered by the vehicle warranty. Make sure you properly secure your vehicle to the tow vehicle. If you are unsure of the vehicle’s configuration, contact an authorized dealer.

What are the warnings related to recreationally towing a vehicle with a manual transmission?

Do not disconnect the battery when recreationally towing your vehicle. This prevents the transfer case from shifting properly and could cause the vehicle to roll, even if the transmission is in gear.
Placing the transfer case in its neutral position could cause your vehicle to freely roll. Make sure you press and hold the brake pedal and the vehicle is in a secure, safe position when you place the transfer case in its neutral position.

What are the guidelines for recreationally towing a vehicle with a manual transmission?

You can only tow your vehicle with all four wheels on the ground by placing the transfer case in its neutral position by engaging the recreational tow feature. Perform the following steps after positioning your vehicle behind the tow vehicle and properly securing them together. Put your climate control system in recirculated air mode to prevent exhaust fumes from entering your vehicle. Failure to put the transfer case in its neutral position can damage vehicle components. You can check the towing status at any time by opening the driver door or turning the ignition to the accessory or on position. Neutral Tow Enabled Leave Transmission in Neutral appears in the instrument cluster display to confirm you can recreationally tow your vehicle. If your vehicle has an anti-theft alarm, make sure you switch perimeter sensing on when towing. A tone could sound for up to 30 minutes if you recreationally tow with the doors removed.

How do I switch Neutral Tow On for a manual transmission?

Switch your vehicle to accessory mode by pressing the push button ignition switch without pressing any pedals.
Press the 2H button on the four-wheel drive mode control.
Leave the gearshift lever in the neutral position and fully press and hold both the clutch and the brake pedal.
Using the instrument cluster controls on the steering wheel, select Settings.
Select Neutral Tow.
Press and hold the OK button until a confirmation message appears in the information display. If completed successfully, the information display shows Neutral Tow Enabled Leave Transmission in Neutral. This indicates that your vehicle is safe to tow with all wheels on the ground. If you do not see a confirmation message in the instrument cluster display, you must perform the procedure again from the beginning. You may hear noise as the transfer case shifts into its neutral position. This is normal.
Release both the clutch and the brake pedals and leave the gearshift lever in the neutral position.
Switch your vehicle off by pressing the push button ignition switch once without pressing any pedals.

How do I switch Neutral Tow Off for a manual transmission?

With your vehicle properly secured to the tow vehicle, switch your vehicle to accessory mode by pressing the push button ignition switch without pressing any pedals.
Starting with both the brake and clutch pedal released, fully press and hold both pedals at the same time for approximately seven seconds. Continue holding both pedals until the instrument cluster display shows 2H and Neutral Tow Disabled. If completed successfully, the instrument cluster displays 2H and Neutral Tow Disabled. You must perform the switching neutral tow on and switching neutral tow off procedures again from the beginning if the indicator light and message do not display. You may hear a noise as the transfer case shifts out of its neutral position. This is normal.
Release the pedals.
Apply the parking brake, then disconnect your vehicle from the tow vehicle.
Release the parking brake, start your vehicle, and shift into either a forward or a reverse gear to make sure the transfer case is out of the neutral tow position.
If the transfer case did not successfully shift out of its neutral position, set the parking brake. Have your vehicle checked as soon as possible.

How do I resolve the Shift Delayed Drive Forward message for a manual transmission?

Fully press and hold both the brake and the clutch pedals.
Press the push button ignition switch.
With the vehicle running, shift into a forward gear and release the clutch. Let the vehicle roll forward up to 3 ft (1 m). You may hear a noise as the transfer case shifts out of its neutral position. This is normal.
Make sure the instrument cluster displays Neutral Tow Disabled.

What are the warnings related to recreationally towing a vehicle with an automatic transmission?

Do not disconnect the battery when recreationally towing your vehicle. This prevents the transfer case from shifting properly and could cause the vehicle to roll, even if the transmission is in park (P).
Placing the transfer case in its neutral position could cause your vehicle to freely roll. Make sure you press and hold the brake pedal and the vehicle is in a secure, safe position when you place the transfer case in its neutral position.

What are the guidelines for recreationally towing a vehicle with an automatic transmission?

How do I switch Neutral Tow On for an automatic transmission?

Switch your vehicle to accessory mode by pressing the push button ignition switch without pressing any pedals.
Press the 2H button on the four-wheel drive mode control.
Fully press and hold the brake pedal and shift the transmission to neutral (N).
Using the instrument cluster controls on the steering wheel, select Settings.
Select Neutral Tow.
Press and hold the OK button until a confirmation message appears in the information display. If completed successfully, the information display shows Neutral Tow Enabled Leave Transmission in Neutral. This indicates that your vehicle is safe to tow with all wheels on the ground. If you do not see a confirmation message in the instrument cluster display, perform the procedure again from the beginning. You may hear noise as the transfer case shifts into its neutral position. This is normal.
Release the brake pedal and leave the transmission in neutral (N).
Switch your vehicle off by pressing the push button ignition switch once without pressing any pedals.

How do I switch Neutral Tow Off for an automatic transmission?

With your vehicle properly secured to the tow vehicle, switch your vehicle to accessory mode by pressing the push button ignition switch without pressing any pedals.
Starting with the brake pedal released and the transmission in neutral (N), fully press and hold the brake pedal for approximately seven seconds and shift the transmission to park (P). Continue holding the brake pedal until the instrument cluster display shows 2H and Neutral Tow Disabled. If completed successfully, the instrument cluster displays 2H and Neutral Tow Disabled. Perform the switching neutral tow on and switching neutral tow off procedures again from the beginning if the indicator light and message do not display. You could hear a noise as the transfer case shifts out of its neutral position. This is normal.
Release the brake pedal.
Apply the parking brake, then disconnect your vehicle from the tow vehicle.
Release the parking brake, start your vehicle, and shift into either drive (D) or reverse ® to make sure the transfer case is out of the neutral tow position.
If the transfer case did not successfully shift out of its neutral position, set the parking brake. Have your vehicle checked as soon as possible.

How do I resolve the Shift Delayed Drive Forward message for an automatic transmission?

Fully press and hold the brake pedal.
Press the push button ignition switch.
With the vehicle running, shift into drive (D). Let the vehicle roll forward up to 3 ft (1 m). You could hear a noise as the transfer case shifts out of its neutral position. This is normal.
Make sure the instrument cluster displays Neutral Tow Disabled.

What are the possible towing information messages?

Message	Description
Neutral Tow Enabled Leave Transmission in Neutral	The transfer case is in the neutral position and your vehicle is safe to tow with all four wheels on the ground.
Shift Delayed Drive Forward	There is a transfer case gear tooth blockage present. With your vehicle on, shift the transmission into drive (D) and let the vehicle roll forward, up to 3 ft (1 m).
Neutral Tow Disabled	The transfer case is not in the neutral position and your vehicle is not safe to tow with all four wheels on the ground.

What are the fuse precautions?

Always disconnect the battery before servicing high current fuses.
To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs.
Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.

Where is the under hood fuse box located?

The under hood fuse box is in the engine compartment.

How do I access the under hood fuse box?

Open the under hood fuse box cover.

What are the fuses in the under hood fuse box and their ratings?

Protected Component	Rating
Body control module -battery power in feed 1.	30 A
Body control module -battery power in feed 2.	30 A
Fuel pump.	30 A
Powertrain control module power.	25 A
Powertrain components.	30 A
Powertrain components.	20 A
Ignition coils.	20 A
Blower motor control module.	40 A
Washer relay.	10 A
Starter motor.	30 A
360 degree camera module.	10 A
Anti-lock brake system module.	10 A
Powertrain control module.	10 A
Power steering module.	10 A
Blind spot information system.	15 A
Rear view camera. Adaptive cruise control. Driveline control module. Transmission control module.	15 A
Anti-lock brake system module.	60 A
Anti-lock brake system module.	60 A
Driver power seat.	30 A
Passenger power seat.	30 A
Auxiliary power point.	20 A
Auxiliary power point.	20 A
Auxiliary power point.	20 A
Heated seat module.	30 A
Trailer brake control module.	30 A
Brake on-off switch.	10 A
SYNC module.	20 A
Heated rear windshield.	40 A
Driveline control module.	40 A
Trailer tow park lamp relay.	30 A
Trailer tow backup lamps.	20 A
Upfitter switch #1.	30 A
Upfitter switch #2.	15 A
Upfitter switch #3.	10 A
Upfitter switch #4.	10 A
Upfitter switch #5.	10 A
Upfitter switch #6.	10 A
Stability bar disconnect module.	10 A
Front windshield wiper.	30 A
Rear windshield wiper.	30 A
Trailer tow light module.	40 A
Left-hand headlamps.	20 A
Right-hand headlamps.	20 A
Trailer tow battery charge.	30 A
Fuel injectors (2.7L).	10 A
USB smart charger 1.	10 A
USB smart charger 2.	5 A
Amplifier.	20 A
Stability bar disconnect module run/start.	10 A
Smart data link control.	10 A
Driver door module.	60 A
Passenger door module.	60 A
Body control module B+.	60 A
Body control module start stop.	30 A

Where is the body control module fuse box located?

The body control module fuse box is in the passenger compartment.

How do I access the body control module fuse box?

Open the body control module fuse box cover.

What are the fuses in the body control module fuse box and their ratings?

Protected Component	Rating
Power windows.	10 A
DC/AC inverter.	10 A
Exterior mirrors.	7.5 A
Wireless charging module.	7.5 A
Anti-theft alarm horn.	10 A
Climate control.	7.5 A
Gateway module.	7.5 A
Steering column control module.	7.5 A
Instrument cluster module.	7.5 A
Ignition switch.	5 A
Headlamps.	5 A
Telematics modem.	5 A
In-vehicle temperature and humidity sensor.	5 A
Brake on-off switch.	5 A
Terrain management switch.	10 A
Integrated control panel switch. Driveline and chassis controls switch panel. 12 inch center display.	10 A
Radio frequency receiver module. Audio control module.	20 A
Run/start relay.	30 A
Automatic high beam.	15 A
Image processing module A.	15 A
Auto-dimming interior mirror.	20 A
Parking assist control module.	20 A
Heated steering wheel.	30 A

What are the different types of fuses?

Micro 2
Micro 3
Maxi
Mini
M Case
J Case
J Case Low Profile
Slotted M Case

When do I need to check a fuse?

If electrical components in the vehicle are not working.

When do I need to replace a fuse?

If a fuse has blown.

How do I identify a blown fuse?

You can identify a blown fuse by a broken wire within the fuse.

What are some maintenance precautions?

Do not work on a hot engine.
Make sure that nothing gets caught in moving parts.
Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation.
Keep all open flames and other burning material, such as cigarettes, away from the battery and all fuel related parts.
Set the parking brake, shift the transmission to park (P) and block the wheels.

How do I open the hood?

Pull the hood release handle under the left-hand side of the instrument panel.
Release the hood latch by pushing the secondary release lever to your left-hand side.
Open the hood and support it with the hood strut.

How do I close the hood?

Fully stow the strut prior to lowering the hood.
To close, lower the hood and make sure that it fully latches.

Where is the engine coolant reservoir located?

The engine coolant reservoir is located in the engine compartment.

Where is the windshield washer fluid reservoir located?

The windshield washer fluid reservoir is located in the engine compartment.

Where is the engine oil dipstick located?

The engine oil dipstick is located in the engine compartment.

Where is the engine oil filler cap located?

The engine oil filler cap is located in the engine compartment.

Where is the brake fluid reservoir located?

The brake fluid reservoir is located in the engine compartment.

Where is the engine compartment fuse box located?

The engine compartment fuse box is located in the engine compartment.

How do you use the side rail to lift and rotate the soft top forward? Use the side rail to lift and rotate the soft top forward, making sure it latches in place. Do not lift using the top rail only. Make sure both sides fully latch. Latch the two latches at the header. Do not drive without the soft top properly latched or fully opened.

How do you access the rear cargo area? Open the tailgate. Unlatch the soft top. Lift the rear of the soft top and support it with the soft top strut.

What should you be careful of when opening, closing, removing, or installing the removable vehicle components? When opening, closing, removing, or installing the removable vehicle components, take care not to get your fingers or hands caught in the mechanism. Failure to follow this instruction could result in personal injury.

How do you remove the soft top? Fully open the soft top. Remove the three fasteners on each side in the rear cargo area using the provided head driver and ratchet. Remove the soft top. Safely store the soft top when it is off your vehicle.

How do you install the soft top? Reverse the removal procedure. Torque the fasteners that secure the soft top to the vehicle to 15 ± 2 lb.ft (20 ± 3 Nm). Make sure the soft top is set flush on the locating pins. Do not overtighten the fasteners, as you can strip them.

How do you install the soft top trim piece? Make sure to install the soft top trim pieces before installing the soft top. Secure the three fasteners to the soft top trim piece on each side of your vehicle using the provided head driver and ratchet.

What are the precautions for removable fenders? Do not drive your vehicle on public roads with fenders removed, as you will lose the protection they provide in a crash. Failure to follow this instruction could result in personal injury or death.

How do you remove the fender flares? Unlock the five quarter-turn clips by turning the clips counterclockwise. Pull outward on the fender flare with your hands to unseat the 5 push pin clips from the sheet metal. Push pins and quarter pins should not be removed from fender flare.

How do you install the fender flares? Press the five push clips in until they are seated. Lock the five quarter-turn clips by turning the clips clockwise.

What are the precautions for storing the doors and the roof panels in a 4-door vehicle? Do not store removed doors or roof panels in the vehicle without using the Ford onboard storage kit, and verifying they have been secured per instructions. Failure to follow this instruction could result in personal injury or death. Cargo can shift under severe vehicle use; to reduce the risk of damage, avoid high-speed or extreme rock crawl off-road situations when storing the doors in the cargo area. Inspect the bags and harness periodically to make sure they are not damaged. Inspect the door retention harness straps to make sure there are no nicks, tears, or cuts; replace if necessary. Clean the roof panels and doors prior to storing them in the bags, as dirt may damage the finish.

How do you store the front roof panels? Remove the front roof panels. Open the bag and pull out the divider. Place the first panel into the bag. Replace the divider before placing the second panel into the bag. Zip the bag closed. Gently slide the roof panel bag into the cargo area.

How do you secure the front roof panels vertically? Raise the bag to the vertical position. Secure the upper roof bag strap around the rear seat headrests. Adjust the tension on the strap until it is snug. Do not overtighten the strap, as this may cause damage to the headrest. Secure the lower bag hooks to the forward cargo rings. Some vehicle accessories may prevent vertical storage of the panels.

How do you secure the front roof panels horizontally? Install the loops through the two D-rings and secure the panels. Do not place objects on the roof panel bag to avoid damaging the panels.

How do you secure the door retention harness? Install the eyebolts located in the Ford onboard storage kit into the rear cargo area pillars. Use the ratchet tool provided in the kit to assist in tightening the eyebolts. The eyebolts should rest in the groove of the handle. Using the tool as a lever, apply force until fully tightened. The eyebolts should be tightened to 13 lb.ft (17 Nm). The eyebolts can remain installed on the vehicle. Make sure the eyebolts are fully tightened each time they are used. Fully open the tailgate and rear lift glass, or open the soft top cargo access and connect the prop rod to hold open. Install the door retention harness; refer to harness label for image. Attach upper straps 1 and 2 to the eyebolts. Attach lower straps 3 and 4 to the forward cargo rings. Place the narrow strap loop over all the rear headrests and tighten until snug. Do not over-tighten the strap, as this may cause damage to the headrest. Place the remaining harness over the seat so it is out of the way.

How do you store the front doors? Adjust the seat backrest to the optimal seating position. Pull the lever up, and push the backrest rearward when storing the two front doors. This creates more space between the front door sail and the upper trim. Ensure the cargo area is clear of any other items. Complete the steps for securing the door retention harness. Open the passenger side front door and install the door bag. Zip the bag fully closed and gently place the door in the cargo area. Avoid contacting the rear pillars, speakers, striker, and trim. For soft tops, take care to avoid contacting the prop rod. Slide the door into position with the bag label facing rearward. Center the door to make sure there is space between the door and cargo box trim panels. Push the lower edge of the door forward until it stops to create space for the door peak. Secure the door bag to the retention harness with the clip. Repeat for the driver side front door. Secure the bags using the clips on the bags. Lift the retention harness over the doors, making sure the straps are straight. Secure the upper straps 5 and 6 to the eyelet bolts and lower straps 7 and 8 to the rear cargo rings. Tighten all adjustable straps to secure the doors. To prevent the doors from moving, fold the unused rear door bags to use as a spacer and place them between the doors and lower cargo hooks. The doors should not move when pressure is applied.

How do you store the front roof panels and the front doors? Adjust the seat backrest to the optimal seating position. Pull the lever up, and push the backrest rearward when storing the two front doors. This creates more space between the front door sail and the upper trim. Ensure the cargo area is clear of any other items. Complete the steps for securing the door retention harness. Open the passenger side front door and install the door bag. Zip the bag fully closed and gently place the door in the cargo area. Avoid contacting the rear pillars, speakers, striker, and trim. Slide the door into position with the bag label facing rearward. Center the door to make sure there is space between the door and cargo box trim panels. Push the lower edge of the door forward until it stops to create space for the door peak. Secure the door bag to the retention harness with the clip. Repeat for the driver side front door. Secure the bags using the clips on the bags. Place the front roof panels in the bag, and then into the cargo area. Do not use the roof bag retention system in this orientation; secure the roof panels by the harness. Lift the retention harness over the doors, making sure the straps are straight. Secure the upper straps 5 and 6 to the eyelet bolts and lower straps 7 and 8 to the rear cargo rings. Tighten all adjustable straps to secure the doors and roof panels. The doors and roof panels should not move when pressure is applied.

How do you store all four doors? Adjust the rear seat backrest to the upright position and raise the center headrest to the highest position. Pull on the seat backrest to make sure that it has fully latched. Ensure the cargo area is clear of any other items. Four-door storage in the cargo area will prevent the soft tops from fully retracting; limit to the partially open position. Make sure the rear seat headrests are upright. Complete the steps for securing the door retention harness. Open the driver-side rear door and install the bag. Zip the bag fully closed and gently place the door in the cargo area. Avoid contacting the rear pillars, speakers, striker, and trim. For soft tops, take care to avoid contacting the prop rod. Slide the door into position with the bag label facing rearward. Align the door peak with the highest point in the upper trim. Secure the door bag to the retention harness with the clip. Repeat for the remaining doors. Secure the bags with the harness clips. In order to store all four doors onboard, you must store the doors in the following sequence: driver-side rear, driver-side front, passenger-side front, passenger-side rear. Lift the retention harness over the doors, making sure the straps are straight. Secure the upper straps 5 and 6 to the eyelet bolts and lower straps 7 and 8 to the rear cargo rings. Tighten all adjustable straps to secure the doors. The doors should not move when pressure is applied. When closing the tailgate, make sure the tailgate and glass do not strike the stowed doors.

What are the precautions for storing roof panels in a 2-door vehicle? The two-door vehicle is not capable of on-board storage of the doors. Store the doors in a secure area to avoid damage. Roof panels should be clean prior to storage in bags as dirt may damage the finish.

How do you store the roof panels in a 2-door vehicle? Remove the front roof panels. Open the bag and pull out the divider. Place the first panel into the bag. Replace the divider before placing the second panel into the bag. Zip the bag closed. Gently slide the roof panel bag into the cargo area in the vertical position. Secure the upper roof bag strap around the rear seat headrests. Adjust the tension on the straps until it is snug. Do not over-tighten the strap, as this may cause damage to the headrest. Secure the lower bag hooks to the forward cargo rings.

What cleaning products are recommended?

Motorcraft® Bug and Tar Remover, ZC-42 (U.S. & Canada)
Motorcraft® Custom Bright Metal Cleaner, ZC-15 (U.S. & Canada)
Motorcraft® Detail Wash, ZC-3-A (U.S. & Canada)
Motorcraft® Engine Shampoo and Degreaser, ZC-20 (U.S.)
Motorcraft® Engine Shampoo, CXC-66-A (Canada)
Motorcraft® Premium Leather and Vinyl Cleaner, ZC-56 (U.S. & Canada)
Motorcraft® Multi-Purpose Cleaner, CXC-101 (Canada)
Motorcraft® Premium Windshield Wash Concentrate with Bitterant, ZC-32-B2 (U.S.)
Motorcraft® Premium Quality Windshield Washer Fluid, CXC-37-F/M (Canada)
Motorcraft® Professional Strength Carpet & Upholstery Cleaner, ZC-54 (U.S. & Canada)
Motorcraft® Premium Glass Cleaner, CXC-100 (Canada)
Motorcraft® Spot and Stain Remover, ZC-14 (U.S.)
Motorcraft® Ultra-Clear Spray Glass Cleaner, ZC-23 (U.S.)
Motorcraft® Wheel and Tire Cleaner, ZC-37-A (U.S. & Canada)

What are the precautions for cleaning the exterior of the vehicle? If you have a Sasquatch or soft top package, wash your vehicle by hand, or by using a touchless commercial wash with no mechanical tracks on the floor. Immediately remove fuel spillages, bird droppings, insect deposits, and road tar from your vehicle. These items may cause damage to your vehicle’s paintwork or trim over time. Remove any exterior accessories, for example, antennas, before entering a car wash.

How do you clean headlamps and rear lamps? Use only cold or lukewarm water containing car shampoo to clean the headlamps and the rear lamps. Do not scrape the lamps. Do not wipe lamps when they are dry.

How do you clean the windshield and wiper blades? Clean the windshield with a non-abrasive glass cleaner. When cleaning the interior of the windshield, avoid getting any glass cleaner on the instrument panel or door panels. Wipe any glass cleaner off these surfaces immediately. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. Do not use razor blades or other sharp objects to clean or remove decals from the inside of the heated rear window. This can cause damage not covered by the vehicle warranty.

How do you clean chrome, aluminum, or stainless steel parts? Use only a car shampoo, a soft cloth, and water on bumpers and other chrome, aluminum, or stainless steel parts. Rinse the area well after cleaning. Do not use abrasive materials, for example, steel wool or plastic pads, as they can scratch these surfaces. Do not use chrome cleaner, metal cleaner, or polish on wheels or wheel covers.

How do you clean the wheels? Only use a recommended wheel and tire cleaner to clean the wheels weekly. Use a sponge to remove heavy deposits of dirt and brake dust. Rinse well after cleaning. Do not apply a cleaning chemical to warm or hot wheel rims and covers. If you intend on parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before parking your vehicle. This reduces the risk of corrosion of the brake discs, brake pads, and linings. Do not clean the wheels when they are hot. Some car washes could damage wheel rims and covers. Using non-recommended cleaners, harsh cleaning products, chrome wheel cleaners, or abrasive materials could damage wheel rims and covers.

How do you clean the engine compartment? Use a vacuum cleaner to remove debris from the screen area below the windshield. If you are not familiar with the parts around the engine, do not wash the engine compartment. Avoid frequent engine washes. Never wash or rinse the engine while it is hot or running. Never wash or rinse any ignition coil, spark plug wire, or spark plug well. Cover the battery, power distribution box, and air filter assembly to prevent water damage. If your vehicle has an engine cover, remove the cover before application of shampoo and degreaser. Spray an approved engine shampoo and degreaser on all parts that require cleaning and rinse with water.

How do you clean the convertible top? Remove lint with a lint roller or vacuum with a soft bristle brush. Wash with an approved high-quality convertible top cleaner and protectant. Do not use stiff bristle brushes, abrasive materials, or household cleaning products. High-pressure water may cause water leaks and possible seal damage to the convertible top.

How do you clean the soft top windows? Use only a microfiber cloth, cold or lukewarm water, and a mild soap and water solution to clean the soft top windows in a circular motion. Rinse thoroughly with cold water, then wipe with a soft, damp cloth. Use a small amount of soft top window cleaner or equivalent to remove fine scratches and to improve visibility and provide UV protection to help prevent yellowing. Test any cleaner on an inconspicuous area before applying broadly. Do not use hot water or anything stronger than mild soap on the soft top window. Do not use solvents such as alcohol or harsh cleaning agents on the soft top window. Do not use a scraper or de-icing chemicals to remove frost, snow, or ice; use warm water only. Do not paste stickers, gummed labels, or any tape on the soft top window surface.

How should you clean stripes or graphics on the vehicle? It is recommended to wash your vehicle by hand; however, pressure washing may be used under the following conditions: Use a spray with a 40° wide spray angle pattern. Keep the nozzle at a 12 in (305 mm) distance and 90° angle to your vehicle’s surface. Do not use water pressure higher than 2,000 psi (14,000 kPa). Do not use water hotter than 179°F (82°C). Holding the pressure washer nozzle at an angle to the vehicle’s surface may damage graphics and cause the edges to peel away from the vehicle’s surface.

How should you clean camera lenses and sensors? Use only lukewarm or cold water and a soft cloth to clean the camera lens and sensors. Do not pressure wash camera lens and sensors.

How do you clean the hard top? Use a sponge to remove dust and loose dirt on the hard top surface. Wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. Make sure the surface of your hard top is dry before applying a small amount of conditioner or spray wax. Test any conditioner or spray wax on an inconspicuous area before applying broadly. Do not use alcohol-containing cleaner or any type of solvent on the hard top surface. Do not use power tools, paste wax, or polish on the hard top surface.

How do you clean the underbody of the vehicle? Regularly clean the underside of your vehicle using water. Keep body and door drain holes free of debris or foreign material.

What are the precautions for cleaning the instrument panel? Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system.

How do you clean the instrument panel? Clean the instrument panel and cluster lens with a damp soft cloth. Dry the area with a clean, soft cloth. Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect you from undesirable windshield reflection.

How do you clean plastic parts? Use only a mild soap and water solution on a soft cloth. Dry the area with a clean, soft cloth.

How do you clean displays and screens? Use only a microfiber cloth in a circular motion to clean off the fingerprint or dust. If dirt or fingerprints are still on the screen, apply a small amount of alcohol to the cloth and try to clean it again. Do not pour or spray alcohol onto the touchscreen. Do not use detergent or any type of solvent to clean the touchscreen.

How do you clean leather and vinyl surfaces? Remove dust and loose dirt with a vacuum cleaner. Wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. Make sure the leather is dry, then apply a small amount of conditioner to a clean, dry cloth. Rub the conditioner into the leather until it disappears. Allow the conditioner to dry, then repeat the process for the entire interior. If a film appears, wipe it off with a dry, clean cloth.

What are the precautions for cleaning fabric seats and headliners? On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a crash.

How do you clean fabric seats and headliners? Remove dust and loose dirt with a vacuum cleaner. Wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. For heavy stains, spot clean the area. If a ring forms on the fabric, clean the entire area immediately, but do not oversaturate or the ring could set.

How do you clean carpets and floor mats? Remove dust and loose dirt with a vacuum cleaner. Wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. For heavy stains, spot clean the area. If a ring forms on the fabric, clean the entire area immediately, but do not over-saturate or the ring could set. Remove dust and loose dirt with a vacuum cleaner. Wash rubber floor mats using mild soap and lukewarm or cold water. Completely dry the floor mat before placing them back in your vehicle.

How do you clean rubber floors? Remove the floor mats prior to washing out. Prior to washing out, remove large debris to prevent clogging the drain. Turn active drain plugs in each passenger compartment counterclockwise to open. Wash out debris using a standard garden-style hose. Use caution to not spray seats, console, door interior, electrical connections, instrument cluster display, and underside of the instrument panel on both driver and passenger sides. Wipe out remaining water or debris from the floor. Install active drain plugs and turn clockwise to close. Reinstall floor mats.

What are the precautions for cleaning seatbelts? Do not use cleaning solvents, bleach, or dye on the vehicle’s seatbelts, as these actions may weaken the belt webbing.

How do you clean seatbelts? Wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth.

How do you repair minor paint damage? Authorized dealers have touch-up paint to match your vehicle’s color. Your vehicle color code is printed on a sticker on the front, left-hand side door jamb. Take your color code to your authorized dealer to make sure you get the correct color. Before repairing minor paint damage, use a cleaner to remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt, and industrial fallout. Read the instructions before using cleaning products.

How often should you wax your vehicle? Wax the high-gloss painted surface of your prewashed vehicle once or twice a year. Use only an approved quality wax that does not contain abrasives. Follow the manufacturer’s instructions to apply and remove the wax. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Avoid waxing unpainted or low-gloss black colored parts; they discolor over time.

How do you prepare your vehicle for storage? Store all vehicles in a dry, ventilated place. If vehicles are stored outside, they require regular maintenance to protect against rust and weather damage. Make sure all linkages, cables, levers, and pins under your vehicle are covered with grease to prevent rust. Move vehicles at least 25 ft (7.5 m) every 15 days to lubricate working parts and prevent corrosion. Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle. Change the engine oil and filter prior to storage because used engine oil contains contaminants which may cause engine damage. Start the engine every 15 days for a minimum of 15 minutes. Run at fast idle with the climate controls set to defrost until the engine reaches normal operating temperature. With your foot on the brake, shift through all the gears while the engine is running. Wash your vehicle thoroughly to remove dirt, grease, oil, tar, or mud from exterior surfaces, rear-wheel housings, and the underside of front fenders. Periodically wash your vehicle if it is stored in exposed locations. Touch up exposed or primed metal to prevent rust. Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when you wash your vehicle. Lubricate all hood, door, and luggage compartment hinges and latches with a light-grade oil. Cover interior trim to prevent fading. Keep all rubber parts free from oil and solvents. Check and recharge the 12-volt battery as necessary. Keep connections clean. It is necessary to reset memory features if you disconnect the battery cables. Make sure the brakes and parking brake release fully. If you intend on parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so to reduce the risk of increased corrosion of the brake discs, brake pads, and linings. Maintain recommended tire air pressure. If you intend on parking your vehicle for an extended period after cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This reduces the risk of corrosion of the brake discs, brake pads, and linings.

How do you remove your vehicle from storage? Change the engine oil before you use your vehicle again. Wash your vehicle to remove any dirt or grease film build-up on window surfaces. Check windshield wipers for any deterioration. Check under the hood for any foreign material that may have collected during storage, such as mice or squirrel nests. Check the exhaust for any foreign material that may have collected during storage. Check tire pressures and set tire inflation per the Tire Label. Check brake pedal operation. Drive your vehicle 15 ft (4.5 m) back and forth to remove rust build-up. Check fluid levels (including coolant, oil, and gas) to make sure there are no leaks, and fluids are at recommended levels. If you remove the battery, clean the battery cable ends and check for damage.

Where is the Tire Label located? The Tire Label is located on the B-Pillar or the edge of the driver’s door.

What do the tire quality grades mean?

Tire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found on the tire sidewall between the tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT-type tires, tires with nominal rim diameters of 10 to 12 inches, or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104 ©(2).

Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 1½ times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Temperature: The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

What is a connected vehicle?

A connected vehicle has technology that allows your vehicle to connect to a mobile network and for you to access a range of features. When used in conjunction with the FordPass app, it could allow you to monitor and control your vehicle further, for example checking the tire pressures, the fuel level and the vehicle location.

What are the connected vehicle requirements?

Connected service and related feature functionality requires a compatible vehicle network. Some remote features require additional service activation. Log in to your Ford account for details. Some restrictions, third party terms and message or data rates may apply.

What is the modem?

The modem allows access to a range of features built into your vehicle.

How do you enable and disable the modem?

Press Settings.
Press Connectivity.
Press Connected Vehicle Features.
Switch vehicle connectivity on or off.

How do you connect FordPass to the modem?

Make sure that the modem is enabled using the vehicle settings menu.
Open the FordPass app on your device and log in.
Add your vehicle or select your vehicle if already added.
Select the option to activate your vehicle.
Make sure that the name on the screen matches the name shown in your FordPass account.
Confirm that FordPass account is connected to the modem.

How do you connect the vehicle to a Wi-Fi network?

Select the settings option on the feature bar.
Press Connectivity.
Press Manage Wi-Fi Networks.
Switch Wi-Fi on.
Press View Available Networks.
Select an available Wi-Fi network. Note: Enter the network password to connect to a secure network.

Why can I not confirm the connection of my FordPass account to the modem?

The modem is not enabled. Switch vehicle connectivity on.
The network signal is weak. Move your vehicle closer to a place where the network signal is not obstructed.

Why can I not connect to a Wi-Fi network?

You entered the wrong network password. Enter the correct password.
The network signal is weak. Move your vehicle closer to the Wi-Fi router or to a place where the network signal is not obstructed.
There are multiple access points in range with the same network name. Choose a unique name for your network. Do not use the default name unless it contains a unique identifier, for example as part of the MAC address.

Why does the Wi-Fi connection disconnect after successful connection?

The network signal is weak. Move your vehicle closer to the Wi-Fi router or to a place where the network signal is not obstructed.

What can I do if I am close to a Wi-Fi router but the network signal strength is weak?

If your vehicle has a heated windshield, position your vehicle so that the windshield is not facing the Wi-Fi router.
If your vehicle has metallic tinting on the windows but not on the windshield, position your vehicle so that the windshield is facing the Wi-Fi router or open the windows that are facing the router.
If your vehicle has metallic tinting on the windows and the windshield, open the windows that are facing the router.
If your vehicle is in a garage and you have the garage door closed, open the garage door as it could block the signal.

Why can I not see a network I expect to see in the list of available networks?

The network is hidden. Make the network visible and try again, or manually add a network in the Wi-Fi settings menu.

Why do software downloads take too long?

The network signal is weak. Move your vehicle closer to the Wi-Fi router or to a place where the network signal is not obstructed.
Wi-Fi network is in high demand or has a slow Internet connection. Use a more reliable Wi-Fi network.

Why does the software not update when the system seems to connect to a Wi-Fi network and the signal strength is excellent?

No software update is available at this time.
Select automatic updates option in the settings menu to enable automatic software update or contact an authorized dealer.
There could be a connection problem. Test the network using another device.

How do you create a vehicle Wi-Fi hotspot?

Select the settings option on the feature bar.
Press Vehicle Hotspot. Note: The vehicle hotspot default setting is on.
Press Settings.
Press Edit.
Press Hotspot visibility. Note: The hotspot visibility default setting is on.

How do you find the Wi-Fi Hotspot Name and Password?

Select the settings option on the feature bar.
Press Vehicle Hotspot.
Press Settings. Note: The network name is the hotspot name.
Press View Password.

How do you connect a device to the Wi-Fi Hotspot?

On your device, switch Wi-Fi on and select the hotspot from the list of available Wi-Fi networks.
When prompted, enter the password.

How do you purchase a data plan?

Connect a device to the hotspot. Note: The vehicle network carrier’s portal opens on your device.
If the portal does not open on your device, open a website and it redirects to the vehicle network carrier’s portal. Note: Secure websites do not redirect.
Follow the instructions on the carrier portal to purchase a plan. Note: If you have an active plan, the system does not redirect to the vehicle network carrier’s portal when you connect a device. Visit the vehicle network carrier’s website to purchase more data. Note: If data usage information is available in the vehicle hotspot menu, it is approximate. Note: If you carry out a master reset, the system does not remove your vehicle from your vehicle network carrier’s account. To remove your vehicle from the account, contact your vehicle network carrier. Note: The vehicle network carrier provides Vehicle Hotspot services, subject to your vehicle network carrier agreement, coverage and availability.

How do you change the vehicle Wi-Fi hotspot name or password?

Select the settings option on the feature bar.
Press Vehicle Hotspot.
Press Settings.
Press Edit.
Press Change Network Name.
Enter your required network name.
Press Done.
Press Change Password.
Enter your required password.
Press Done.

How do you change the Wi-Fi Hotspot Frequency?

Select the settings option on the feature bar.
Press Vehicle Hotspot.
Press Settings.
Press Edit.
Select a frequency. Note: The vehicle hotspot frequency band is selectable depending upon your device capabilities. You will not be able to connect your device to the vehicle hotspot if it does not support the selected frequency band.

Why can I not see the Wi-Fi hotspot name when I search for Wi-Fi networks on my cell phone or other device?

Make sure Wi-Fi hotspot visibility is on.
The system does not provide a Wi-Fi hotspot at this time.
Check what frequency the hotspot is transmitting in the vehicle hotspot settings menu. If the frequency is 5 GHz and your device cannot see the network, change the frequency to 2.4 GHz.

How do you switch the audio unit on and off?

Press the button on the volume control.

How do you select the audio source?

Audio Unit Press to open the media source menu. You can press this multiple times to change the audio source or scroll through the media sources.
Touchscreen Press Sources on the touchscreen to open the media source menu.

How do you play or pause the audio source?

Audio Unit Press the button to pause playback. Press again to resume playback.
Touchscreen Press the button to pause playback. Press again to resume playback. Note: Not all sources can be paused.

How do you adjust the volume?

Turn the volume control. Some vehicles may be able to adjust the volume using buttons on the steering wheel.

How do you switch shuffle mode on and off?

Press the button on the touchscreen to switch shuffle mode on or off. Note: Not all sources have shuffle mode.

How do you switch repeat mode on and off?

Press the button on the touchscreen to switch repeat mode on or off. Note: Not all sources have repeat mode.

How do you set a memory preset?

Select a station or channel.
Press and hold a memory preset button on the touchscreen. Note: The audio mutes briefly while the system saves the preset and returns once it is stored. Note: You can save presets from multiple sources to the memory preset bar.

How do you mute the audio?

Press the button on the steering wheel to mute the audio. Press to mute the signal. Press again to restore the signal.

How do you adjust the sound settings for Balance and Fade (If Equipped)?

Press Settings on the touchscreen.
Press Sound Settings.
Press Balance / Fade.
Press the arrows to adjust the settings.

How do you adjust the sound settings for Tone Settings?

Press Settings on the touchscreen.
Press Sound Settings.
Press Tone Settings.
Press the arrows or slider bar to adjust the settings.

How do you adjust the sound settings for Speed Compensated Volume?

Press Settings on the touchscreen.
Press Sound Settings.
Press Speed Compensated Volume.
Press a setting.

How do you adjust the sound settings for Occupancy Mode (If Equipped)?

Press Settings on the touchscreen.
Press Sound Settings.
Press Occupancy Mode.
Press a setting.

How do you adjust the sound settings for Sound Mode (If Equipped)?

Press Settings on the touchscreen.
Press Sound Settings.
Press Sound Mode.
Press a setting.

How do you set the clock and date?

Press Settings on the touchscreen.
Press Clock Settings.
Set the time. Note: The AM and PM options are not available if 24-hour mode is on.

How do you switch Automatic Time Updates on and off?

Press Settings on the touchscreen.
Press Clock Settings.
Switch Automatic time zone update on or off.

How do you manually select a radio station?

Turn to search through the radio frequency band.

How do you use Direct Tune to select a radio station?

Press Direct Tune to open the number pad.
Enter the station you prefer. Note: You can only enter a valid station for the audio source you are currently listening to.

How do you use Seek to select a radio station?

Press either button. The system stops at the first station it finds in that direction.

How do you switch the display on and off?

Audio Unit Press the button.
Touchscreen To switch the display off:
1. Press Settings on the touchscreen.
2. Press Display Settings.
3. Press Display Off. Note: The display defaults to on each time you switch your vehicle on. To switch the display on, press anywhere on the touchscreen.

How do you switch Digital Radio reception on and off?

Press Settings on the touchscreen.
Press Radio Settings.
Switch AM HD Radio or FM HD Radio on or off.

How do you locate the satellite radio identification number?

Select SiriusXM as the audio source.
Tune to channel 0.

How do you manually select a satellite radio channel?

Press the button to find the previous or next available radio channel.

How do you use the linear tuner to select a satellite radio channel?

The linear tuner is displayed when manually selecting a channel. You can swipe left or right on the linear tuner carousel to navigate through the channel list. Tap on a channel title to listen to it.

How do you use Direct Tune to select a satellite radio channel?

Press the channel up or down button to open the linear tuner screen.
Press Direct Tune to open the number pad.
Enter the channel you prefer.

How do you use Browse to select a satellite radio channel?

Press Browse.
Select a channel.

How do you save SiriusXM Favorites?

Tapping the currently tuned channel or show logo on the SiriusXM audio screen. A favorite icon appears next to the logo when it is saved as a favorite.
Tuning to a channel or show you want to save as a favorite. Navigate to the SiriusXM Favorites screen and press the Add Current button. The currently tuned channel or show is saved as a favorite.
Saving a radio preset. This saves the currently tuned SiriusXM channel or show as a favorite. Note: Requires a trial or active subscription to use.

What should I do if I see a “Connectivity Disabled” error message for satellite radio?

Internet connectivity is turned off. See Connected Vehicle (page 417). Internet streaming and On Demand shows are unavailable and some SiriusXM features are disabled.

What should I do if I see a “No Internet” error message for satellite radio?

SYNC will attempt to connect. See Satellite Radio Limitations (page 426). Switch to a satellite connection for the current channel if the option is available. The audio system may mute. A “Switch to Satellite” button may be displayed on the SiriusXM audio screen if the channel is also available via satellite.

What should I do if I see a “No Satellite Signal” error message for satellite radio?

The antenna may be obstructed or satellite reception is weak in your location. See Satellite Radio Limitations (page 426). Switch to an internet connection for the current channel if the option is available. The audio system may mute. A “Switch to Internet” button may be displayed on the SiriusXM audio screen if the channel is also available via streaming.

What should I do if I see a “Slow Network Connection” error message for satellite radio?

Allow some time for audio to load or tune to a different channel. The audio system may mute while audio attempts to load.

What should I do if I see a “Channel Unavailable” error message for satellite radio?

A temporary update may be in progress. Allow some time before retrying to tune to the channel. If issue persists, the channel may no longer be available. The audio system may mute. Radio may tune to a different channel.

What should I do if I see an “Episode Unavailable” error message for satellite radio?

A temporary update may be in progress. Allow some time before retrying to play the episode. If issue persists, the episode may no longer be available. The audio system may mute. Radio may tune to a different channel.

What should I do if I see a “Something went wrong” error message for satellite radio?

Retry action after some time or tune to a different channel. The audio system may mute. Radio may tune to a different channel.

What should I do if I see a “Subscribe to Listen” error message for satellite radio?

Your subscription has expired or you have not yet subscribed for access to the listed content. Navigate to Subscription under the Satellite Radio Settings menu. If you have an active subscription which includes the listed channel or content and you see this error, you may need to refresh your radio. To refresh your SiriusXM radio, visit http://www.siriusxm.com/refresh in the US, or http://www.siriusxm.ca/refresh in Canada. You may need to provide your SiriusXM Radio identification number. See Locating the Satellite Radio Identification Number (page 427). You cannot listen to selected content. Content may appear grayed out and some features may be disabled.

What should I do if I see an “Upgrade to Listen” error message for satellite radio?

Your subscription does not include access to the listed content. You may need to upgrade your subscription. Navigate to Subscription under the Satellite Radio Settings menu. If you have an active subscription which includes the listed channel or content and you see this error, you may need to refresh your radio. To refresh your SiriusXM radio, visit http://www.siriusxm.com/refresh in the US, or http://www.siriusxm.ca/refresh in Canada. You may need to provide your SiriusXM Radio identification number. See Locating the Satellite Radio Identification Number (page 427). You cannot listen to selected content. Content may appear grayed out and some features may be disabled.

What should I do if I see a “Location Restricted Content” error message for satellite radio?

Content is not available in your location or SiriusXM is unable to determine your location. Tuning to a different channel may resolve the issue. The audio may mute. “Not available in your location” or “Unable to determine your location” may be displayed.

What should I do if I see a “Channel Blocked” error message for satellite radio?

The Block Explicit Content filter is turned on. Navigate to Listener Settings under the Satellite Radio Settings menu to access the Block Explicit Content filter. Navigate to Listener Settings. See Satellite Radio Settings (page 427). The audio may mute. The radio may tune to a different channel.

What should I do if I see an “Antenna Problem or Hardware Problem” error message for satellite radio?

If issue persists, you may need to visit an authorized dealer for service. Audio may mute. Access to SiriusXM features may be unavailable.

What should I do if I see a “SiriusXM Updating…” error message for satellite radio?

Allow SiriusXM some time to complete updating. The audio may mute.

What should I do if I see a “Loading…” error message for satellite radio?

No action necessary. If loading time is longer than usual, see Satellite Radio Limitations (page 426). Audio may mute. Content may be temporarily unavailable while loading.

What should I do if I see a “SiriusXM Loading…” error message for satellite radio?

No action necessary. Allow SiriusXM some time to finish loading. Audio may mute. Content and controls may be temporarily unavailable.

What are the speed-restricted features that are not available while the vehicle is in motion at or above 5 mph (8 km/h)?

System updates.
Personal profiles setup.
Valet mode setup.
Driver assistance settings.
Vehicle Settings.
MyKey setup.
Door keypad code setup.
Backup start passcode setup.

How do you use the radio, a USB, a media player or a Bluetooth device from the feature bar?

Press the button to use the radio, a USB, a media player or a Bluetooth® device.

How do you make calls and access the phonebook on your cell phone from the feature bar?

Press the button to make calls and access the phonebook on your cell phone.

How do you use the navigation system from the feature bar?

Press the button to use the navigation system.

How do you use shortcuts from the feature bar?

Press the button to replace this button with a shortcut to a feature or setting.

How do you search for and use compatible apps on your iOS or Android device from the feature bar?

Press the button to search for and use compatible apps on your iOS or Android device.

How do you adjust system settings from the feature bar?

Press the button to adjust system settings.

How do you view features from the feature bar?

Press the button to view features. Note: The icon may be different depending on your vehicle.

How do you view the next or previous card on the information on demand screen?

Press the button to view the next card.
Press the button to view the previous card.

How do you view available cards on the information on demand screen?

Press the button to view available cards.

What are some examples of general voice interaction commands?

Result	Command
The system resets the current voice interaction.	Start Over.
The system ends the current voice interaction.	Cancel.
The system goes to the next page.	Next Page.
The system goes to the previous page.	Previous Page.
The system displays a list of available commands you can use on the current screen.	Help.

What are some examples of entertainment voice interaction commands?

Result	Command
The system plays the selected music.	Play The Beatles.
The system shows the selected music.	Show music by The Beatles.
The system tunes the radio to 101.9 FM.	Tune to FM 101.9.
The system tunes the radio to Sirius Channel 2.	Set the station to Sirius Channel 2.

What are some examples of climate voice interaction commands?

Result	Command
The system sets the temperature to the minimum.	Set the temperature to low.
The system sets the temperature to 72°F (22°C).	Set the temperature to 72°F (22°C).

What are some examples of phone voice interaction commands?

Result	Command
The system calls Henry using your connected device.	Call Henry.
The system dials the selected phone number.	Dial (phone number).
The system begins a dictated text message.	Send a text message to Henry.
The system reads you the most recent message from Henry.	Read my message from Henry.

What are some examples of apps voice interaction commands?

Result	Command
The system prompts you to say the name of an app to start it on the system.	Mobile Apps.
The system will list all of the currently available Mobile Apps.	List Mobile Apps.
The system will search and connect to compatible app running on your mobile device.	Find Mobile Apps.

What are some examples of navigation voice interaction commands?

Result	Command
The system begins guided navigation to the address.	Drive to 125 Main Street, New York.
The system searches for the requested point of interest.	Where is ___
The system shows directions to the selected intersection.	Show me directions to Oakwood Boulevard and Pelham Road.
The system ends guided navigation to the destination.	Cancel route.

What are some examples of Ford Assistant voice interaction commands?

Result	Command
The vehicle tells you how much gas it has left.	How much gas is in my tank?

What are some examples of Maintenance and Roadside Assistance voice interaction commands?

Result	Command
Your vehicle calls the roadside assistance phone number.	Call roadside assistance.

What are some examples of Vehicle Information voice interaction commands?

Result	Command
Information about the feature appears on the center display or FordPass app.	How does cruise control work?
Information about the warning light appears on the center display or FordPass app.	What does the warning light mean?
Information about open recalls appears on the center display or FordPass app.	Am I affected by any recalls?

How do you connect your phone?

Go to the settings menu on your device and switch Bluetooth® on.
Press the phone option on the feature bar.
Press Add Phone. Note: A prompt alerts you to search for your vehicle on your cell phone.
Select your vehicle on your cell phone. Note: A number appears on your cell phone and on the touchscreen.
Confirm the number on your cell phone matches the number on the touchscreen. Note: The touchscreen indicates that you have successfully paired your cell phone.
Download the phonebook from your cell phone when you are prompted. Note: If you pair more than one cell phone, use the phone settings on the center display to specify the primary phone. You can change this setting at any time.

What options are in the phone menu?

Recent Call List: Display and select an entry from a list of previous calls.
Contacts: Display a smart search form to look up your contacts. Use the List button to alphabetically sort your contacts.
Favorites: Display the list of favorite contacts that are set up on your phone.
Messaging: Displays the list of text messages to read, listen to, or respond to.
Email: Displays the list of emails to read, listen to, or respond to.
Phone List: Display the list of paired or connected devices that you can select. Note: Up to 12 devices can be stored.
Do Not Disturb: Reject incoming calls and switch ring tones and alerts off.
Phone Keypad: Directly dial a number.
Voice Control: Say a command to use the Google or Siri voice assistant available on your connected phone to access supported features. Note: Some features under the phone menu may not be available if the feature is not supported through the phone.

How do you make calls from your contacts?

Select Contacts. You can then select the name of the contact you want to call. Any numbers stored for that contact display along with any stored contact photos. You can then select the number that you want to call. The system begins the call.

How do you make calls from your recent call list?

Select Recent Call List. You can then select an entry that you want to call. The system begins the call.

How do you make calls from your favorites?

Select Favorites. You can then select an entry that you want to call. The system begins the call.

How do you make calls using the keypad?

Select Phone Keypad. Select the digits of the number you wish to call. The system begins the call. Pressing the backspace button deletes the last digit you typed.

How do you receive calls?

During an incoming call, an audible tone sounds. Caller information appears in the display if it is available. To accept the call, select Accept. Note: You can also accept the call by pressing the phone button on the steering wheel. To reject the call, select Reject. Ignore the call by doing nothing. The system logs it as a missed call.

What can you do during a phone call?

During a phone call, the contacts name and number display on the screen along with the call duration. The phone status items are also visible:

Signal Strength.
Battery.

You can select any of the following during an active phone call:

End Call: Immediately end a phone call. You can also press the button on the steering wheel.
Keypad: Press this to access the phone keypad.
Mute: You can switch the microphone off so the caller does not hear you.
Privacy: Transfer the call to the cell phone or back to the touch-screen.

How do you send and receive a text message?

Hear It: Hear the text message.
View: View the text message.
Call: Call the sender.
Reply: Reply to the text message with a standard text message.

How do you switch text message notification on and off?

The settings on your device must be enabled to receive text message notifications on the center display. Check your device settings to enable these features.

How do you connect a Bluetooth® device?

Make sure Bluetooth® is enabled on your device.
Press Settings on the touchscreen.
Press Connectivity.
Press Bluetooth.
Press Add a Bluetooth Device. Note: A prompt alerts you to search for your vehicle on your device.
Select your vehicle on your device. Note: A number appears on your device and on the touchscreen.
Confirm that the number on your device matches the number on the touchscreen. Note: The touchscreen indicates that you have successfully paired your device.

How do you play media using Bluetooth®?

Connect your device.
Press the audio button on the feature bar.
Press Sources.
Press the Bluetooth® option.
Press to play a track. Press again to pause the track.
Press to skip to the next track. Press and hold to fast forward through the track.
Press once to return to the beginning of a track. Repeatedly press to return to previous tracks. Press and hold to fast rewind through the track.

How do you access apps?

Select the apps option on the feature bar.

How do you enable apps on an iOS device?

Select the apps option on the feature bar.
Select Mobile Apps Help.
Follow the instructions to pair and connect your device via Bluetooth® or with a USB cable.
Start the apps on your device that you want to use.
Select the app that you want to use on the touchscreen. Note: Some apps may run through Apple CarPlay if it is enabled. Note: Closing an app on your device will close it on the touchscreen. Note: For troubleshooting assistance select Compatible Apps List or My App Isn’t Listed under Mobile Apps Help.

What are some 12V Battery Precautions?

Do not allow battery fluid to come into contact with your eyes, skin, fabrics, or painted surfaces. The battery contains sulfuric acid, which can cause burns. Keep sparks, flames, and lit tobacco away from the battery. When you need to charge the battery, make sure there is good ventilation.

How does the Battery Management System work?

The Battery Management System (BMS) works by monitoring the battery’s condition. The system regulates the charging and discharging of the battery.

What is the 12V Battery – Troubleshooting section about?

The 12V Battery – Troubleshooting section provides information about how to resolve common issues related to the 12V Battery.

What information is found in the 12V Battery – Information Messages section?

This section provides information about the various messages related to the 12V Battery.

What information is found in the 12V Battery – Warning Lamps section?

This section provides information about the various warning lights related to the 12V Battery.

What are some 360 Degree Camera Precautions?

Do not use the 360 degree camera as a replacement for safe driving practices.
Be aware that objects might appear closer or farther away than they actually are.
Be aware that objects that are moving may appear to be stationary.
Be aware that the 360 degree camera has limitations.

What are some 360 Degree Camera Limitations?

The camera view might be obscured by dirt, snow, or other obstructions.
The camera view might be affected by bright or low light conditions.
The camera view might not be accurate in all situations.

What are some Adaptive Cruise Control Precautions?

Adaptive cruise control is not a substitute for safe driving practices.
Always pay attention to the road and be ready to apply the brakes.
Do not use adaptive cruise control in heavy traffic, on winding roads, or on slippery surfaces.
Adaptive cruise control may not detect all vehicles.

What are some Adaptive Cruise Control Limitations?

Adaptive cruise control may not work properly if the radar sensor is blocked or dirty.
Adaptive cruise control may not work properly in poor weather conditions.
Adaptive cruise control may not work properly on steep hills.

What is Alert Mode?

Alert Mode is a function of the Lane Keeping System that provides steering assistance.

How does Alert Mode work?

Alert Mode works by using a camera to detect lane markings. If the vehicle begins to drift out of its lane, the system will provide steering assistance to help bring the vehicle back into the lane.

What are some AM/FM Radio Limitations?

AM/FM radio reception can be affected by terrain, distance from the transmitter, and other factors.

What are some Anti-Lock Braking System Limitations?

The anti-lock braking system may not work properly in certain situations, such as on loose gravel or snow.

What are some Audio System Precautions?

Do not operate the audio system in a way that distracts you from driving safely.
Keep the volume at a level where you can still hear outside traffic and emergency signals.

What information is found in the Audio System – Troubleshooting section?

This section provides information about common audio system issues and how to resolve them.

What information is found in the Audio System – Information Messages section?

This section provides information about the various messages related to the audio system.

What is the Auto-Dimming Interior Mirror?

The auto-dimming interior mirror automatically reduces glare from the headlights of vehicles behind you.

How does Automatic Engine Stop work?

Automatic engine stop works by shutting off the engine when the vehicle comes to a complete stop. The engine will automatically restart when you release the brake pedal or press the accelerator.

What is Automatic High Beam Control?

Automatic high beam control is a feature that automatically switches between high beams and low beams, depending on traffic conditions.

How does Automatic High Beam Control Work?

Automatic high beam control uses a sensor to detect the headlights or taillights of other vehicles. When other vehicles are detected, the system automatically switches to low beams. When no other vehicles are detected, the system automatically switches to high beams.

What are some Automatic High Beam Control Precautions?

Automatic high beam control is not a substitute for safe driving practices.
Always pay attention to the road and be ready to manually switch to low beams.
Automatic high beam control may not work properly in all situations.

What are some Automatic High Beam Control Limitations?

Automatic high beam control may not detect all vehicles, such as motorcycles or bicycles.
Automatic high beam control may not work properly in poor weather conditions.
Automatic high beam control may not work properly on winding roads.

What are some Automatic Transmission Positions?

Park (P)
Reverse ®
Neutral (N)
Drive (D)
Sport (S)
Manual (M)

What are some Automatic Transmission Precautions?

Do not shift into park (P) while the vehicle is moving.
Do not shift into reverse ® while the vehicle is moving forward.
Always come to a complete stop before shifting between drive (D) and reverse ®.

What is Auto Mode?

Auto mode is a setting on the climate control system that automatically adjusts the temperature and fan speed to maintain a comfortable temperature.

What is Auto-Start-Stop?

Auto-start-stop is a feature that automatically shuts off the engine when the vehicle comes to a complete stop. The engine will automatically restart when you release the brake pedal or press the accelerator.

What information is found in the Auto-Start-Stop – Troubleshooting section?

This section provides information about how to resolve common issues related to the auto-start-stop system.

What are some Auto-Start-Stop Precautions – Automatic Transmission?

Auto-start-stop may not work properly in certain situations, such as on steep hills or in heavy traffic.
Auto-start-stop may not work properly if the battery is low.
Always be prepared to manually restart the engine.

What are some Auto-Start-Stop Precautions – Manual Transmission?

Auto-start-stop may not work properly in certain situations, such as on steep hills or in heavy traffic.
Auto-start-stop may not work properly if the battery is low.
Always be prepared to manually restart the engine.

What information is found in the Auto-Start-Stop – Information Messages section?

This section provides information about the various messages related to the auto-start-stop system.

What is Autounlock?

Autounlock is a feature that automatically unlocks the doors when the vehicle is shifted into park (P).

What information is found in the Blind Spot Information System – Troubleshooting section?

This section provides information about how to resolve common issues related to the blind spot information system.

What information is found in the Blind Spot Information System – Information Messages section?

This section provides information about the various messages related to the blind spot information system.

What is the Body Control Module Fuse Box?

The body control module fuse box is a central location for fuses that protect the electrical circuits in the vehicle.

What is Brake Shift Interlock?

Brake shift interlock is a safety feature that prevents the vehicle from being shifted out of park (P) unless the brake pedal is pressed.

What are some Brake Shift Interlock Precautions?

Always press the brake pedal before shifting out of park (P).
Do not attempt to override the brake shift interlock system.

What information is found in the Brakes – Troubleshooting section?

This section provides information about common brake system issues and how to resolve them.

What information is found in the Brakes – Information Messages section?

This section provides information about the various messages related to the brake system.

What information is found in the Brakes – Warning Lamps section?

This section provides information about the various warning lights related to the brake system.

What are some Catalytic Converter Precautions?

Do not park the vehicle over dry grass or other flammable materials, as the catalytic converter can get very hot.
Do not modify or tamper with the catalytic converter.

What information is found in the Catalytic Converter – Troubleshooting section?

This section provides information about common catalytic converter issues and how to resolve them.

What information is found in the Catalytic Converter – Warning Lamps section?

This section provides information about the various warning lights related to the catalytic converter.

What is the Center Console?

The center console is a storage area located between the front seats.

What are some Center Display Limitations?

The center display may not be visible in direct sunlight. The center display may not work properly in extreme temperatures.

What are some Cleaning the Exterior Precautions?

Do not use harsh chemicals or abrasive cleaners.
Do not wash the vehicle in direct sunlight.
Always dry the vehicle with a soft cloth or chamois.

What are some Connecting a Trailer Precautions?

Always make sure that the trailer is properly connected and secured.
Do not exceed the vehicle’s maximum towing capacity.
Be aware of the additional length and weight of the trailer when driving.

What information is found in the Connecting a Trailer – Troubleshooting section?

This section provides information about common trailer connection issues and how to resolve them.

What information is found in the Connecting a Trailer – Information Messages section?

This section provides information about the various messages related to trailer connection.

What is Automatic Crash Shutoff?

Automatic crash shutoff is a safety feature that automatically shuts off the fuel pump and other systems in the event of a crash.

How does the Automatic Crash Shutoff work?

Automatic crash shutoff works by detecting an impact and then automatically shutting off the fuel pump and other systems.

What is Jump Starting the Vehicle?

Jump starting the vehicle is a procedure for starting the vehicle with the help of another vehicle.

What is the Post-Crash Alert System?

The post-crash alert system is a safety feature that automatically activates the hazard lights and sounds the horn after a crash.

How does the Post-Crash Alert System Work?

The post-crash alert system is activated by the crash sensors and then automatically activates the hazard lights and sounds the horn.

What are some Post-Crash Alert System Limitations?

The post-crash alert system may not activate in all types of crashes.

What is Post Impact Braking?

Post impact braking is a safety feature that automatically applies the brakes after a crash to help prevent secondary collisions.

How does Post Impact Braking Work?

Post impact braking is activated by the crash sensors and then automatically applies the brakes.

What are some Post Impact Braking Limitations?

Post impact braking may not activate in all types of crashes.

What is Crawler Gear?

Crawler gear is a low-speed gear that is designed for off-road driving or when extra low-speed torque is needed.

What are some Cross Traffic Alert Precautions?

Cross traffic alert is not a substitute for safe driving practices.
Always pay attention to the road and be ready to apply the brakes.
Cross traffic alert may not detect all vehicles, pedestrians, or other objects.

What are some Cross Traffic Alert Limitations?

Cross traffic alert may not work properly in poor weather conditions.
Cross traffic alert may not work properly if the sensors are blocked or dirty.
Cross traffic alert may not work properly in certain situations such as parking.

What information is found in the Cross Traffic Alert – Troubleshooting section?

This section provides information about common cross traffic alert system issues and how to resolve them.

What are some Digital Radio Limitations?

Digital radio reception can be affected by terrain, distance from the transmitter, and other factors.

How does Digital Radio Work?

Digital radio works by transmitting radio signals in a digital format. This provides better sound quality and more channels than traditional analog radio.

What is Distance Indication?

Distance indication is a feature of the pre-collision assist system that displays the distance to the vehicle in front of you.

What information is found in the Electric Parking Brake – Warning Lamps section?

This section provides information about the various warning lights related to the electric parking brake.

How does Electric Power Steering Work?

Electric power steering uses an electric motor to assist the steering system.

What are some Electric Power Steering Precautions?

Do not attempt to modify or tamper with the electric power steering system.
If the electric power steering system fails, you may lose power steering assistance.

What is Electronic Locking Differential?

The electronic locking differential is a feature that locks the rear wheels together to provide extra traction in off-road conditions.

What information is found in the Electronic Locking Differential – Troubleshooting section?

This section provides information about common electronic locking differential issues and how to resolve them.

What information is found in the Electronic Locking Differential – Information Messages section?

This section provides information about the various messages related to the electronic locking differential.

What are some Emergency Call Limitations?

The emergency call system may not work in all locations.
The emergency call system may not work if there is no cellular service available.

What is Evasive Steering Assist?

Evasive steering assist is a feature that provides steering assistance to help you avoid a collision.

What are some Evasive Steering Assist Limitations?

Evasive steering assist may not work properly in all situations.

What are some Fuel and Refueling Precautions?

Do not smoke or use open flames near the fuel filler area.
Always turn off the engine before refueling.
Always use the correct type of fuel.
Do not overfill the fuel tank.

What information is found in the Fuel and Refueling – Troubleshooting section?

This section provides information about common fuel and refueling issues and how to resolve them.

What information is found in the Fuel and Refueling – Information Messages section?

This section provides information about the various messages related to fuel and refueling.

What information is found in the Fuel and Refueling – Warning Lamps section?

This section provides information about the various warning lights related to fuel and refueling.

What is the Fuel Gauge?

The fuel gauge indicates the amount of fuel remaining in the fuel tank.

What are some Fuel Gauge Limitations?

The fuel gauge may not be accurate in all situations.

What is Distance to Empty?

Distance to empty is an estimate of how far the vehicle can travel on the remaining fuel.

What is the Low Fuel Reminder?

The low fuel reminder is a warning light or message that indicates that the fuel level is low.

What are some Fuse Precautions?

Always replace a fuse with a fuse of the same amperage rating.
Do not attempt to modify or tamper with the fuse box.
If a fuse repeatedly blows, have the electrical system inspected by a qualified technician.

What information is found in the Fuses – Troubleshooting section?

This section provides information about common fuse issues and how to resolve them.

What is the Under Hood Fuse Box?

The under hood fuse box is a central location for fuses that protect the electrical circuits in the engine compartment.

What information is found in the Fuses – Frequently Asked Questions section?

This section provides answers to frequently asked questions about fuses.

What is G.O.A.T. Mode Control?

G.O.A.T. Mode Control is a system that allows you to select from various driving modes. These modes can be used to optimize performance for different conditions, such as snow, sand, or rocks.

What information is found in the G.O.A.T. Mode Control – Troubleshooting section?

This section provides information about common G.O.A.T. Mode Control system issues and how to resolve them.

What information is found in the G.O.A.T. Mode Control – Information Messages section?

This section provides information about the various messages related to the G.O.A.T. Mode Control.

What information is found in the Headlamps – Troubleshooting section?

This section provides information about common headlamp issues and how to resolve them.

What information is found in the Headlamps – Frequently Asked Questions section?

This section provides answers to frequently asked questions about headlamps.

What are some Heated Seat Precautions?

Do not use the heated seats if you have a medical condition that makes you sensitive to heat.

How does Hill Descent Control Work?

Hill descent control works by automatically applying the brakes to maintain a slow and controlled speed when driving down a steep hill.

How does Hill Start Assist Work?

Hill start assist works by holding the brakes for a brief moment when you release the brake pedal on a hill, which prevents the vehicle from rolling backward.

How does Pre-Collision Assist Work?

Pre-collision assist works by using radar and camera sensors to detect potential collisions. If a collision is imminent, the system will provide warnings and may automatically apply the brakes.

How does Stability Control Work?

Stability control works by using sensors to monitor the vehicle’s direction and speed. If the system detects that the vehicle is starting to lose control, it will automatically apply the brakes and adjust engine power to help bring the vehicle back under control.

How does the 360 Degree Camera Work?

The 360 degree camera system uses multiple cameras to provide a bird’s-eye view of the vehicle’s surroundings.

How does the Garage Door Opener Work?

The garage door opener works by transmitting a radio signal to your garage door opener receiver.

How does the Lane Keeping System Work?

The lane keeping system works by using a camera to detect lane markings. If the vehicle begins to drift out of its lane, the system will provide steering assistance to help bring the vehicle back into the lane.

How does the Personal Safety System Work?

The personal safety system is a network of airbags, seatbelts, and sensors that work together to protect the occupants of the vehicle in the event of a crash.

How does the Rear Occupant Alert System Work?

The rear occupant alert system works by detecting when a rear door is opened and then displaying a message to remind the driver to check the rear seats before leaving the vehicle.

How does the Safety Canopy™ Work?

The safety canopy is a system of airbags that deploys from the roof rails and provides side impact protection.

How does Traction Control Work?

Traction control works by monitoring the wheel speed. If the system detects that one or more wheels are starting to slip, it will automatically apply the brakes and adjust engine power to help restore traction.

How does Trailer Sway Control Work?

Trailer sway control works by using sensors to detect when a trailer is starting to sway. If the system detects trailer sway, it will automatically apply the brakes and adjust engine power to help stabilize the trailer.

How do the Front Airbags Work?

The front airbags inflate rapidly in the event of a frontal collision to cushion the occupants of the front seats.

How do the Side Airbags Work?

The side airbags inflate rapidly in the event of a side collision to cushion the occupants of the front seats.

What information is found in the Interior Lighting – Troubleshooting section?

This section provides information about common interior lighting issues and how to resolve them.

What information is found in the Interior Lighting – Frequently Asked Questions section?

This section provides answers to frequently asked questions about interior lighting.

What is the Auto-Dimming Interior Mirror?

The auto-dimming interior mirror automatically reduces glare from the headlights of vehicles behind you.

What are some Interior Mirror Precautions?

Do not attempt to modify or tamper with the interior mirror.

What information is found in the Keys and Remote Controls – Troubleshooting section?

This section provides information about common key and remote control issues and how to resolve them.

What information is found in the Keys and Remote Controls – Information Messages section?

This section provides information about the various messages related to keys and remote controls.

What information is found in the Keyless Entry – Frequently Asked Questions section?

This section provides answers to frequently asked questions about keyless entry.

What are some Lane Keeping System Limitations?

The lane keeping system may not work properly in poor weather conditions.
The lane keeping system may not work properly if the lane markings are not visible.
The lane keeping system may not work properly on sharp curves.

What are some Lane Keeping System Precautions?

The lane keeping system is not a substitute for safe driving practices.
Always pay attention to the road and be ready to manually steer the vehicle.
Do not rely on the lane keeping system to keep you in your lane.

What information is found in the Lane Keeping System – Troubleshooting section?

This section provides information about common lane keeping system issues and how to resolve them.

What information is found in the Lane Keeping System – Frequently Asked Questions section?

This section provides answers to frequently asked questions about the lane keeping system.

What information is found in the Lane Keeping System – Information Messages section?

This section provides information about the various messages related to the lane keeping system.

CLICK HERE TO DOWNLOAD FORD BRONCO 2022 (01) PDF MANUAL

FORD BRONCO 2022 (01) PDF SUMMARY:

Visitors also searched:

Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.Cancel reply

Discover more from Manual-Hub.com