FLINQ SMART OUTDOOR GAIA FQC8273 (01) PDF Document

This light is suitable for OUTDOOR use only. Please read the manual carefully before use. This appliance may be used by children aged 12 and over, and by persons with reduced physical, sensory or mental capacities, provided they are supervised or have been trained in safe use. Cleaning and maintenance must not be carried out by children without supervision. Children must not be allowed to play with the appliance.

Warning:

Do not leave packaging material lying around carelessly. This may become dangerous playing material for children. Risk of suffocation!

DANGER due to swallowing small parts. Keep these away from children. Risk of suffocation!

During the first use of the product, place the product in a place with sufficient direct sunlight for first charging at a minimum time for 2-3 days in the OFF switch position. When the sky is overcast, this period should be extended.

The operating life of the product will be less if the ambient temperature is higher than 45°C or lower than -10°C.

When the lamp is in a location that receives less sunlight, it will operate for fewer hours per night. Insufficient charging will affect performance and may result in the lamp going off before dawn. The solar panel is best directed as much as possible towards the south to maximize exposure to direct sunlight.

The four different seasons can affect the lighting time. The solar light will work longer in summer than during winter. Your solar lights will produce more hours of operation when installed in an area free from cover, shade, or shadowing. Due to low sunlight intensity and severe weather in autumn and winter, the total lighting time will be reduced.

Select a location that is not close to other light sources, such as street lighting, as this enables the lamp to be switched off automatically. Maximum lighting time depends on sunlight and daytime charging. Minimum charging time is 5-7 hours in direct sunlight.

If snow or ice is on top of the solar panel, please remove it at all times so the battery can be charged correctly.

The battery level can be checked by the FLINQ app at all times (except when empty).

During winter time or when the sunshine duration is short, it is suggested to switch to power OFF and charge when sunlight is available before powering ON again.

New batteries must be recharged and discharged 3-5 times before their full function use time is released. Charge indoors only at room temperature and only under supervision during daytime. Disconnect from the charger when the battery is fully charged, as overcharging can shorten battery life. Lithium batteries should only be charged with constant current/constant voltage (CC/CV). When not in usage, the charge in a fully charged battery slowly disappears. Do not place the product near a heat source or expose it to direct sunlight, dust, moisture, rain or mechanical impact. Try to keep the battery temperature between 0°C and 45°C at all times. If the battery is too hot or too cold, the product may not work temporarily, even if it is fully charged. Do not attempt to charge the device when the battery is damaged. The rechargeable battery is built into the device and can be replaced. Do not throw the battery into the fire, otherwise it may explode. After 3 months long storage, need to completely discharged and recharge for at least 80%. The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, short contacts, heat above 60°C (140°F), or incinerate. Keep away from children.

Light on

Push the ON/OFF button to ON to activate the lamp and the green led indicator will turn on. The lamp will turn ON automatically at sunset/night and will go OFF during sunrise/day (or when the battery is empty).

Light off

If you push the ON/OFF button to OFF again, the lamp is turned OFF completely and the green led indicator is off. The solar cells will charge the battery without activating the lamp. Leave the lamp in this position for at least 2 or 3 sunny days so the battery can be fully charged before using it or when not in use for a longer period of time to protect the battery.

When powered ON by the ON button, the default factory setting is “auto motion detection sensor mode”. It is suggested to use this mode at all times for the most convenient use as it stays off and charges during the daytime and will be ON at night/evening.

When you press the MODE button once, the lamp will go into “manual” mode. This means the lamp will be always ON (without motion detection sensor) at all times and will only be OFF when switched off by the app or when the battery is fully empty.

When you press the MODE button for a second time, it will cancel the “manual” mode and switch off the lamp completely. Pressing the MODE button again will return it to “auto motion sensor mode”.

During solar charge, the red charging indicator will be ON if there is enough sun received by the solar panel. When the red light is OFF and GREEN is ON, it means the battery is fully charged. The battery level can be checked by the FLINQ app.

Choose a stable, solid, and supportive ground surface like paths, driveways, or gardens, and ensure the lamp is faced towards the direction of the sun (most south location).

Step 1. Connect pole and lamp

Align the ground stake holder inside the lamp part, connecting them together at a 90-degree angle as shown in the picture.

Step 2. Place ground pin

Click the cross-fitted ground pin upwards into the main housing and make sure it fits tight and straight.

Step 3. Place lamp

Flip it over and install and push downwards in the desired location. Place it in the best sunny location possible while installing on a soft ground location.

Step 4. Water drainage

Make sure you place the lamp slightly backwards so that no water can collect on the solar panel.

Note: Please ensure that only 2.4 GHz networks are supported. 5GHz networks will not work. Make sure your mobile device is running iOS 9 & higher or Android 5 & higher and Bluetooth is turned ON.

Step 1. Open or download app

Open the FlinQ app or download it from the iOS App Store or Google Play Store. Login or register and continue.

Step 2. Turn on the lamp

Make sure the lamp is set up, placed, and powered ON during the first setup and within a range of 10 meters max between your mobile device and the lamp.

Step 3. Turn on pairing mode

The red LED will quickly flash to indicate it’s ready to pair/connect after turning on the lamp. If not, hold the mode button for 3-5 seconds to turn on pairing mode.

Step 4a. Add device (automatically)

The new smart Gaia lamp will pop up on the app. Follow the instructions within the application during connection and configuration.

Step 4b. Add device (manually)

If not detected automatically, tap the “+” button or “Add device” button and select the Gaia lamp from the “Lights” tab.

Step 5. Follow instructions

Now follow the instructions within the application during connection and configuration.

Step 6. Device is being added

The device is being installed. This can take up to 2 minutes.

Step 7. Device added successfully

The device is installed successfully and added to your list of products. You can now set up timers and control your device remotely.

To control your FLINQ SMART OUTDOOR GAIA FQC8273 by using your voice via a smart speaker, such as Google Home or Amazon Alexa, please refer to the manufacturer’s instruction manual on how to enable a voice command through your device.

If you experience any problems, please restore the lamp to factory default and set it up again from the start.

When the product will not be used for a long time, please place it in a location with sufficient sunlight, with a charging time of at least 1-3 days in the OFF position. To maintain the battery’s function, it is better to comprehensively charge the product in a place with sufficient sunlight once a month.

The solar lamp should be installed in a place with sufficient sunlight to ensure the solar panel will absorb sunlight sufficiently, so that the working hours of the solar lamp will be prolonged.

If snow or ice is on top of the solar panel, please remove it at all times so the battery can be charged correctly by the panel.

This solar light is only used for domestic private and non-commercial use.

When using electrical products, certain precautions must be followed, including:

Choose a stable, solid and supportive surface and make sure the lights are set correctly.

This lamp is intended for outside use.

This is not a TOY; keep away from small children below 12 years.

Do not place or immerse the lamp under water like in pools and ponds. It is not FULL waterproof (IP68).

Do not use with appliances that could cause any fire in unattended use (like irons etc.).

Do not use the device excessively and do not store it under heavy pressure. The device is not resistant to extreme heat.

Do not open or disassemble the lamp yourself, as this will void the warranty.

Do not disassemble, repair or modify the product by yourself, as this may result in an electric shock.

Do not stand, sit on, jump or throw with the lamp at all times.

Do not throw this product in the air to avoid damage caused by falling.

Only use the lamp for its intended designed use as a light.

Never touch the plug contacts with sharp or metal objects.

Use only the original power supply and original accessories.

Protect the device from special liquids and vapors.

This IPX5 product is suitable for outdoor use.

Do not install near a gas or other sources with a similar heating process.

Do not use the product outside its intended use.

When disassembling, carefully remove the product from its location (ground, trees, bushes, table etc.) to avoid any pressure on the Solar Light that could damage the component elements. In case of non-use, store the product in a cool and dry place away from direct sunlight and switch to the OFF position.

The solar panel is clean (if not, please clean it).

The solar cell was mounted so that it is able to receive as much as possible direct sunlight during the day.

The battery is sufficiently charged (if not, leave for 1-2 sunny days charging in the OFF position).

This indicates a weak battery. Let the lamp charge again for 1-2 sunny days (or 3-4 “Ordinary” days) in the OFF position.

For best results, you need to replace the battery every 24-36 months. When replacing the batteries, use only the type: 18650 3.7V 2200 mAh Li-Ion batteries. Use only the same type and same specification of batteries in the light. It is time to replace the batteries when a shorter operating time than normal is detected, even though the solar light receives a full charge of 8 hours in direct sunlight.

Remove the battery compartment cover on the bottom of the main housing using a screwdriver to remove the screws, remove the cover and rubber seal (if applicable) to gain access to the battery compartment. Remove the old battery and dispose of it correctly according to local law. When refitting the cover, make sure that the gasket and rubber sealing is properly positioned to prevent the ingress of water. Make sure the new battery is a rechargeable 1x 3.7V Li-Ion 2200 mAh rechargeable 18650 battery.

Note: Non-professionals should not disassemble the lamp.

Install the new battery and take care of the proper connection. Close the battery compartment with the screws and make sure the sealing is done properly.

Press the mode button for 3 seconds to go back to factory settings.

Make sure the solar panel is kept dust free and clean. Clean it regularly with a dry cloth and with warm, soapy water. Dirty solar panels may not fully charge the battery. This can lead to premature aging of the battery and may result in unreliable operation of the device.

Please do not immerse the main unit in water; it is not waterproof.

Wipe gently with a clean soft cloth (microfiber) dampened with water or a mild detergent.

Do not use a strong irritant lotion such as gasoline, alcohol, or rubber water.