FISHER & PAYKEL ACTIVESMART RF170B (01) PDF Document

The temperature of the fresh food compartment in your FISHER & PAYKEL ACTIVESMART RF170B can be altered using the internal control panel, located at the front right of the compartment.

The fresh food compartment light will be automatically illuminated, and the temperature will be shown as a series of lights.

Press the – or + buttons to change the temperature. One press on either button will reduce or increase the number of lights by one, indicating a small change in temperature. Fewer lights illuminated means a cooler temperature for the compartment.

To adjust the freezer temperature on your FISHER & PAYKEL ACTIVESMART RF170B, press the freezer compartment button on the internal control panel once. The freezer compartment light will illuminate.

You can then alter the temperature by pressing the – or + buttons. A single press reduces or increases the number of lights, indicating a small temperature change. Fewer lights mean a cooler temperature.

Note: Successively pressing the compartment button will scroll between the compartments. When the door is re-opened, the control panel will automatically return to the fresh food compartment setting.

The ‘Alarm Mute’ function is useful when you need to have the refrigerator door open for longer than normal, such as when cleaning. It silences the door alarm for 20 minutes.

To activate: Press the ‘Alarm Mute’ button once. The ‘Alarm Mute’ light will illuminate.

To deactivate manually: Press the ‘Alarm Mute’ button again. The light will turn off.

The function will automatically deactivate after 20 minutes, and the door alarms will return to normal.

The door alarms on your FISHER & PAYKEL ACTIVESMART RF170B alert you when a door has been left open:

• If the fresh food compartment door is left open, the alarm will beep after 90 seconds.

• If the freezer door is left open, the alarm will beep after 60 seconds.

• While either door remains open, subsequent beeps will sound every 30 seconds for 5 minutes.

• A continuous alarm will sound if either door has been open for 5 minutes or longer, and the interior light(s) will turn off. The alarm stops only when the door(s) is closed.

Note: If ‘Alarm Mute’ is activated, the door alarms are silenced for 20 minutes. After 5 minutes of a door being open, the compartment light will still turn off, but the normal alarms will be suspended.

The ‘Key Mute’ function allows you to silence all button presses on the internal control panel of your FISHER & PAYKEL ACTIVESMART RF170B.

• To activate: Press and hold the ‘Alarm Mute’ button for 4 seconds. The ‘Key Mute’ icon will illuminate on the control panel. Door alarms and the ‘Bottle Chill’ alarm will still operate.

• To deactivate: Press and hold the ‘Alarm Mute’ button for 4 seconds. The ‘Key Mute’ icon will no longer be illuminated.

‘Key Lock’ disables the buttons on the internal control panel, which is useful when cleaning your refrigerator.

• To activate: Press and hold the – and + buttons simultaneously for 4 seconds. The lock icon will illuminate. Pressing any button will now cause a raspberry beep to indicate they are disabled.

• To deactivate: Press and hold the – and + buttons again for 4 seconds. The lock icon will turn off.

To activate Sabbath Mode on your FISHER & PAYKEL ACTIVESMART RF170B:

1. Open the door(s) of the fresh food and freezer compartments.

2. Press and hold the freezer compartment button, ‘Alarm Mute’ button, and – button simultaneously for 4 seconds.

3. The candle icon will illuminate to confirm Sabbath Mode is activated.

While in Sabbath mode:

• All lights on the internal control panel, except the candle icon, will be off.

• Interior lights will not operate when doors are opened.

• Door alarms will not operate.

• Opening the door(s) will not affect the compressor or fans.

Sabbath Mode automatically deactivates after 80 hours. To deactivate it manually, press and hold the same three buttons (freezer compartment, ‘Alarm Mute’, and –) for 4 seconds.

The ‘Bottle Chill’ function on your FISHER & PAYKEL ACTIVESMART RF170B rapidly chills beverages in the freezer. The timer is set for 15 minutes.

• To activate: Press the ‘Bottle Chill’ button on the internal display. The ‘Bottle Chill’ light will illuminate, and an icon will appear on the external display (if your model has one).

• After 15 minutes: An alarm will sound. To silence it, press the ‘Bottle Chill’ button on the internal control panel. For Ice & Water models, the icon will flash on the external display; press the dispenser lock button to silence the alarm.

• To deactivate early: Press the ‘Bottle Chill’ button again. The light will turn off.

Remember to remove your beverage from the freezer after the alarm sounds.

‘Fast Freeze’ boosts the freezing speed by dropping the freezer to its coldest temperature for 12 hours. This helps retain the freshness, texture, and taste of fresh food being frozen.

• To activate: Press the ‘Fast Freeze’ button on the internal display. The ‘Fast Freeze’ light will illuminate.

• To deactivate: Press the ‘Fast Freeze’ button again before the 12 hours have elapsed. Otherwise, it will deactivate automatically.

For best results, activate the function before you place food in the freezer.

The ‘Ice Boost’ function increases ice production by up to 30% for times when you require more ice, such as during a party. It deactivates automatically after 24 hours.

• To turn on: Press the ‘Ice Boost’ button on the internal control panel. The light above the button will illuminate. Activating ‘Ice Boost’ will automatically turn ice making on.

• To turn off manually: Press the ‘Ice Boost’ button again. The light will turn off.

The ‘Ice Boost’ function will pause if the ice bin becomes full.

The water dispenser on your FISHER & PAYKEL ACTIVESMART RF170B is designed for one-handed operation.

• To dispense water: Gently push the dispensing pad with a glass or container. Only a gentle press is needed.

• To stop the flow: Simply pull your glass away from the pad.

Note that pressing very hard against the pad will not make the dispenser operate faster or produce more water. After installation, a few drips may appear for a few days as trapped air is cleared.

The ‘Dispenser Lock’ prevents water from being dispensed, which is useful for cleaning or when small children are around.

• To activate the lock: Press and hold the lock button on the external display for 4 seconds. The light above the ‘Dispenser Lock’ icon will illuminate.

• To deactivate the lock: Press and hold the lock button again for 4 seconds. The light will turn off, and water dispensing will be enabled.

After replacing the water filter cartridge on your FISHER & PAYKEL ACTIVESMART RF170B, you must reset the indicator. Do not reset the indicator before the filter is changed, as this will lead to inaccurate monitoring.

To reset the filter indicator, press and hold the ‘Alarm Mute’ button and the + button on the internal control panel simultaneously for 4 seconds. The filter icon on the internal and external displays will turn off.

Yes, if no filter is fitted to your FISHER & PAYKEL ACTIVESMART RF170B, you can disable the filter indicator so you are not reminded to change it.

• To disable: Press and hold the freezer compartment button, ‘Alarm Mute’ button, and + button for 4 seconds. The filter icon on the internal and external displays will flash once.

• To re-enable: Press and hold the same three buttons again for 4 seconds. The filter icon on the internal and external displays will flash twice.

It is recommended not to disable the indicator if you have a filter fitted to the connection.

To turn your automatic ice maker on, press the ‘Ice On/Off’ button on the internal control panel. The light above the icon will illuminate when the ice maker is on.

Turn your ice maker off if:

• There is no water supply for several hours.

• You are removing the ice storage bin for a period of time.

• You are going on holiday/vacation.

Ensure all bins are in place when the ice making function is activated.

Your FISHER & PAYKEL ACTIVESMART RF170B comes with a smaller ice bin inside the larger freezer bin.

• For a large amount of ice, remove the smaller ice storage bin and allow ice to fall directly into the larger bin.

• For maximum ice storage, level the stored cubes with the ice scoop.

• Use the ‘Ice Boost’ function to increase ice production by up to 30% for a 24-hour period.

If your FISHER & PAYKEL ACTIVESMART RF170B has a manual ice system, follow these steps:

1. Take the ice tray and lid from the top of the ice storage bin.

2. Remove the lid from the ice tray and fill the tray with clean water.

3. Place the lid back on the ice tray and carefully position it back onto the ice storage bin.

4. Once the ice is solid, take the ice tray and lid off the storage bin. Remove the lid from the tray.

5. Twist the ice tray at each end in opposite directions to loosen the cubes.

6. Turn the ice tray over the ice storage bin to dislodge the cubes into the bin.

Each fruit and vegetable bin in your FISHER & PAYKEL ACTIVESMART RF170B has a humidity slide control that can be adjusted depending on what is stored:

• For vegetables (high humidity): Slide the control towards the setting with more drips (lettuce, spinach, broccoli). This creates a more humid environment.

• For fruits (low humidity): Slide the control towards the setting with fewer drips (oranges, lemons, limes). This creates a less humid environment.

• For a mix of fruit and vegetables: Adjust the position of the control to the center.

If you notice too much water in the bins, you can adjust the control towards the fruit setting (fewer drips) and/or wipe out the excess water.

To move your FISHER & PAYKEL ACTIVESMART RF170B refrigerator:

1. Turn off the appliance and unplug it from the power point.

2. Remove all food.

3. Turn the adjustable front feet to the right as far as they will turn to raise them.

4. Ease the refrigerator out of its position. The appliance is fitted with front and rear rollers for forward and backward movement. Avoid moving it sideways to prevent damage to the rollers or floor.

5. Tuck the power cord away, tape the shelves in place, and tape the doors closed.

6. If the cabinet needs to be laid down, carefully lay it on its right side (when viewed from the front).

After relocating, if the appliance has been on its side, leave it standing upright for a few hours before turning it on to allow the refrigeration system pressures to equalize.

For short holidays, it is recommended to leave your FISHER & PAYKEL ACTIVESMART RF170B operating.

For longer holidays (vacations) where you want to turn off the ice maker:

1. Turn the ice maker to OFF on the internal control panel.

2. Shut off the water supply to the refrigerator.

Upon your return:

1. Turn on the water supply to the refrigerator.

2. Dispense 4qt (4L) of water and discard it to ensure the water tank is refilled with fresh water.

3. Turn on the ice maker.

4. Discard the first 3 harvests of ice (8 ice cubes are produced per harvest).

The front feet of your FISHER & PAYKEL ACTIVESMART RF170B can be used to align the doors if they are uneven.

• If the left-hand door is too low: Unscrew the left front foot to lift that side of the cabinet until the top edges of the two doors are aligned.

• If the right-hand door is too low: Adjust the right front foot in the same way.

The refrigerator should be installed leaning backward slightly, with the front approximately 1/2″ (10mm) higher than the back, to ensure a good door closing action.

If your FISHER & PAYKEL ACTIVESMART RF170B is unstable (i.e., it rocks or one front foot is off the floor), follow these steps:

1. Gently push the refrigerator back until the rear rollers contact the floor.

2. Measure the gap under the front foot that has come off the floor.

3. Obtain some solid packing material (e.g., hardwood, plastic) that fits firmly into this gap. Do not use metallic materials.

4. Wind both front feet up and roll the product out of position.

5. Place the packing material on the floor in the location diagonally opposite the unstable front foot (i.e., under the rear roller).

6. Roll the refrigerator back into position and adjust the front feet as per the installation instructions, checking for alignment and door closing action.

7. Check that the product is stable (all 4 feet are on the floor). If not, repeat the process.

For stainless exterior doors:

• Clean with liquid dishwashing detergent dissolved in warm water and a soft cloth.

• Dry the door with a lint-free cloth.

• Do not use any abrasive or stainless steel cleaners and solvents as they will damage the door surface.

For other exterior surfaces:

• Clean with a mix of warm water and liquid dishwashing detergent, and a soft cloth.

• If necessary, clean the magnetic door gasket and recessed handles with an old toothbrush, warm water, and liquid dishwashing detergent.

It is important to keep the interior of your FISHER & PAYKEL ACTIVESMART RF170B clean. Ideally, this should be done every 1 to 2 weeks.

1. Remove the shelves from the cabinet and door. Wash shelves and storage bins in warm water and detergent; rinse in clean water and dry before replacing.

2. Wipe over the interior surfaces with warm water and liquid dishwashing detergent. Alternatively, you can use 1 tsp of baking soda dissolved in 1/2qt (500ml) of warm water. Rinse with clean water.

3. To help remove odors, add a few drops of vanilla essence or vinegar to the water before cleaning.

4. Clean interior surfaces with warm water and liquid dishwashing detergent. Use a toothbrush for the magnetic door gasket.

5. Do not use harsh, abrasive cloths on any part of the refrigerator or freezer.

If the humidity control lid and slides become separated from the glass shelf, follow these steps to reassemble:

1. Turn the shelf upside down.

2. To attach the humidity slides, fit the bottom clips into the shelf front trim corners. Then, slide them sideways towards the shelf until the arm clips onto the glass.

3. To attach the humidity control lid, with the text facing you, align the lid with the front of the shelf. Hold the lid vertically and fit the front end into the retainer on the shelf. Ensure the lid fits into the retainer and underneath the humidity slides.

4. At the sides of the shelf, adjust the humidity slide tabs so that the plastic lid is between the shelf and the tabs.

5. If there are clips on the back of the shelf, fasten the lid with these rear clips. Ensure the cover is fully secure at the front and back of the shelf.

In the unlikely event a fault occurs with your FISHER & PAYKEL ACTIVESMART RF170B, a fault icon will illuminate on the internal control panel and an alarm will sound when the fresh food compartment door is opened.

You should count the number of beeps and also take note of the number and sequence of temperature lights displayed on the internal control panel. Then, contact the Customer Care Center with this information.

To silence the fault alarm, press any button on the internal control panel. The fault icon will remain illuminated until the fault is corrected.

Your FISHER & PAYKEL ACTIVESMART RF170B may produce sounds that are different from your old refrigerator. These are normal.

• Fan air flow sound: Fans change speed depending on demand, circulating cold air. This is quite normal.

• Cracking or popping: May occur when the defrost function is operating.

• Running water sound: This is the liquid refrigerant in the system and can be heard as a boiling or gurgling noise.

• Audible hissing sound: May be heard after closing the freezer door due to the pressure difference between warm and cooled air.

If this is your first refrigerator with an ice maker, you will also hear normal ice making sounds:

• Motor operation (low humming).

• Running water as the ice maker/water tank fills.

• Water valve opening and closing (hissing sound).

• Ice being loosened from the tray (cracking).

• Ice dropping into bin (clunking).

If your FISHER & PAYKEL ACTIVESMART RF170B is not operating, check the following:

• Power Connection: Check that the plug is correctly connected to the power outlet and the power is switched on.

• Power Outlet: Check another appliance at the same outlet to ensure there is power.

• House Fuse: Check your house fuse box.

If the light and display are not working on your FISHER & PAYKEL ACTIVESMART RF170B, check these possible causes:

• Refrigerator Power: Ensure the refrigerator is turned on at the wall.

• Sabbath Mode: The product may be in ‘Sabbath Mode’. To exit this mode, press and hold the freezer compartment button and ‘Alarm Mute’ button together for 4 seconds.

The motor on your FISHER & PAYKEL ACTIVESMART RF170B may run for extended periods due to several reasons:

• Hot weather: In high ambient temperatures, the refrigerator will run longer to maintain its set temperature.

• Frequent door openings: Each time the door is opened, cold air escapes and the refrigerator must run to cool down again.

• Large amount of food recently added: Adding a large quantity of warm food will require the motor to run longer to cool it.

To resolve this, minimize door openings to allow the temperature to stabilize.

If the storage compartments feel too warm, consider these causes:

• Incorrect Temperature Setting: The temperature may be set too high. Refer to the ‘Temperature control’ section to set a cooler temperature.

• Frequent Door Openings: Opening the doors frequently allows warm air in. Minimize door openings to allow the temperature to stabilize.

• Large Amount of Food Added: Adding a large amount of food at once will temporarily raise the temperature.

• Doors Not Sealing Properly: Check that the cabinet is level and that the door gasket seals are clean and sealing properly.

If food is freezing in the fresh food compartment, it may be due to one of the following reasons:

• Incorrect Temperature Setting: The temperature control may be set too low (too cold). Refer to the ‘Temperature control’ section to select a warmer setting.

• Food Placement: Food placed directly in front of the cold air outlets can freeze. Move chill-sensitive foods away from the center back of the shelves.

Condensation in the vegetable bins is formed by the water produced by fruit and vegetables. A small amount of condensation is normal and beneficial for storage. If there is excess water:

• Wipe out the water with a cloth.

• Set the humidity slide to the low humidity setting (the icon with fewer drips).

It is perfectly normal for the exterior of the cabinet to feel warm. This is part of the normal refrigerator operation, designed to prevent condensation from forming on the outside of the appliance.

If a tray or bin is not sliding smoothly, check for these issues:

• Packaging Trapped: Check to ensure no food or packaging is trapped behind the tray/bin.

• Runners Need Resetting: If the runners are not extending fully, they may need to be reset. Hold onto the sides of the tray/bin and extend the runners fully by using a firm pull. This will reset the runner mechanism.

Inefficient operation can be caused by an accumulation of dust on or behind the rear compartment cover. This restricts airflow and reduces efficiency. Refer to the ‘Cleaning and caring for your refrigerator’ section for instructions on how to clean this area. If the problem persists, please contact Customer Care.

If the automatic ice maker on your FISHER & PAYKEL ACTIVESMART RF170B is not producing ice, check the following:

• Ice Maker is Off: Make sure the ice maker has been turned on via the internal control panel.

• Bin Placement: Ensure the ice bin is in the correct position. For some models, the scoop should be on the right side. The ice bin must sit directly under the ice maker on the top left side of the freezer.

• Water Supply: Check that the water supply is turned on and connected.

• Freezer Compartment: Verify that the freezer compartment is working correctly.

• Water Pressure: Check for low water pressure.

• Water Line: Inspect the water line for any kinks or squashing.

• Filter: The water filter may be clogged and need replacing.

If your ice cubes have an unpleasant odor or taste, consider the following solutions:

• Old Cubes: Old ice cubes need to be discarded. Empty the bin and allow the ice maker to produce a fresh batch.

• Unsealed Food: Unsealed packages in the freezer can transmit odors. Ensure all food packaging is properly sealed.

• Cleaning: The interior of the freezer or the ice storage bin may need cleaning. Empty and wash the ice storage bin and clean the freezer interior.

• Incoming Water: The poor taste may be from your incoming water supply. The water filter may need changing, or a new filter may need to be installed.

If your refrigerator is slow to produce ice, it could be for these reasons:

• Door Ajar: The freezer door may have been left ajar. Ensure the door is closed properly.

• Freezer Too Warm: The freezer compartment temperature may be too warm. Turn the temperature to a colder setting.

Wet or clumping ice can be caused by several factors:

• Low water pressure.

• A blocked filter.

• Long or frequent freezer door openings.

• High ambient temperature.

• The ice bin being left out of the freezer for a length of time.

To fix, gently tap the ice with the scoop to unstick it. If large clumps have formed, empty the ice bin and make new ice.

A flashing filter warning light indicates that the water filter needs replacing. You should replace the filter as soon as possible to ensure water and ice quality.

Ice buildup inside the freezer is typically caused by the freezer door not closing tightly. Arrange the items in your freezer to ensure nothing is obstructing the door and preventing it from closing completely. You should also check and clean the door gasket seal to ensure it is making a proper seal.

If the ‘Ice Boost’ function is not noticeably increasing the rate of ice production, it could be due to:

• High Ambient Temperature: The room temperature is very warm, making it harder for the freezer to cool quickly.

• High Usage: The refrigerator is in high usage, with frequent door openings. This lets warm air in and slows the freezing process.

To improve performance, try to minimize door openings.

If the water has a poor taste or odor, it is likely because the refrigerator has not been used for an extended period, causing water in the lines to become stale. To fix this, dispense 4qt (4L) of water to flush the system and allow the fresh water supply to be replenished.

The first glass of water may be warm if:

• The dispenser has not been used for an extended period. Discard the first glass of water dispensed.

• The chilled water tank capacity was used recently. Allow time for the water to cool.

Drips overflowing the drip-shelf can happen when there is air in the system or after a new filter is installed.

• If there is air trapped in the tank: Flush 3qt (3L) of water through the dispenser, stopping intermittently to allow the air to clear.

• If a new filter was just installed: Flush 4qt (4L) of water through the filter and then an additional 3qt (3L) through the dispenser.

A slowed water flow rate is typically caused by a restricted (clogged) filter cartridge. You should replace the filter as soon as possible.