FISHER & PAYKEL DCS ADR136 (01) PDF DOCUMENT

Do Not store or use gasoline or other flammable vapors and liquids inside or in the vicinity of this or any other FISHER & PAYKEL DCS ADR136 appliance. An LP cylinder not connected for use shall not be stored inside or in the vicinity of this FISHER & PAYKEL DCS ADR136 unit.

Do not allow children or pets to play in or around the FISHER & PAYKEL DCS ADR136 Access Drawers.

Clean the FISHER & PAYKEL DCS ADR136 Access Drawers regularly using a mild dish washing liquid and water.

To maintain the exterior appearance, apply a stainless steel polish to the outside surfaces on a regular basis.

Sanitize the FISHER & PAYKEL DCS ADR136 Access Drawers surfaces each season as necessary.

To prevent the formation of mold or mildew, do not store cloth napkins or tablecloths in the FISHER & PAYKEL DCS ADR136 Access Drawers for long periods.

Cooking utensils that are stored in the FISHER & PAYKEL DCS ADR136 Access Drawers should be stored in sealable plastic bags and/or washed each time before re-use.

To prevent personal injury or damage to the FISHER & PAYKEL DCS ADR136 drawers, do not overload them. The maximum rating per drawer is 75 pounds.

Closing drawers may cause injury to your hands or fingers.

Always close or open drawers using their handles.

Be sure to keep hands away from drawer edges when opening or closing drawers.

Begin by insuring proper installation and servicing.

Follow the installation instructions in this manual.

To extend the service life of your FISHER & PAYKEL DCS ADR136 product, be sure to follow the use and care guidelines in this manual.

Do not store items of interest to children above or on the inside of any FISHER & PAYKEL DCS ADR136 appliance. Children could be seriously injured if they should climb onto or into the appliance to reach these items.

The dimensions for FISHER & PAYKEL DCS Access Drawers models are as follows:

Inspect the FISHER & PAYKEL DCS ADR136 Access Drawers to verify that there is no shipping damage.

If any damage is detected, call the shipper and initiate a damage claim. FISHER & PAYKEL DCS ADR136 is not responsible for shipping damage.

Do not discard any packing material (box, pallet, straps) until the FISHER & PAYKEL DCS ADR136 unit has been inspected.

Operate the FISHER & PAYKEL DCS ADR136 drawers to be sure they glide smoothly.

Examine the FISHER & PAYKEL DCS ADR136 drawer fronts to be sure there are no dents or scratches or discoloring.

Cabinet face should be clean and flat.

All angles must be at 90° and plumb.

Support structure must be resistant to moisture damage.

All gas lines and plumbing must be done before installing FISHER & PAYKEL DCS ADR136 access drawers.

Do not use any harsh products (acid, solvent, sealers) around this FISHER & PAYKEL DCS ADR136 unit.

Any cabinet and/or ground preparations must be completed prior to FISHER & PAYKEL DCS ADR136 installation.

Make a cut-out in your cabinet or island with the following dimensions:

Each corner of the cutout should be 90° for the Access Drawers to fit properly.

Island installation to use minimum of 3 vents providing 10 sq. in. per vent (typical).

Place 2 X 4s to provide support for the FISHER & PAYKEL DCS ADR136 Access Drawers structure in the locations indicated. Board lengths are provided in the table below:

To ensure proper drawer operation, be sure your support boards are flat & level. When installing your support boards, be sure they are level. Ensure that the bottom of the center divider rests on top of the support boards. Dependent on application, top of 2×4’s must be 1/2″ above the bottom edge of the cutout.

For proper support & drawer operation, ensure that support boards are level front to back & side to side.

Once the FISHER & PAYKEL DCS ADR136 unit has been inspected, remove the drawers by pulling them out until their slider latch is visible. Carefully push the latch down on the left side while pulling up on the right side and pull the drawers completely out of the frame. To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or table cloth. To remove the FISHER & PAYKEL DCS ADR124 drawer, pull the drawer out and lift the end by the handle to disengage the rollers.

With the help of an assistant, lift the FISHER & PAYKEL DCS ADR136 unit and slide it into the cabinet cutout. Adjust for level and fit. Locate mounting holes on the frame. Secure the unit using screws suited for the type of cabinet material. Depending on the wall thickness and location of mounting holes, an additional board may be required to properly receive the screws.

Re-install the drawers by extending their guides.

While holding the drawer parallel to the cabinet, carefully align & engage the ends of the glides. Slide the drawer in about an inch so that the glides are supporting the back of the drawer.

While holding the drawer up by the handle, pull the glides from the drawer cavity out over the drawer glide until they click.

As you push the drawers in, you will encounter moderate resistance. Continue to push the drawer all the way in to complete the engagement process. The drawer will now glide smoothly in & out with light effort.

Your LP tank will be installed in the recess provided in the bottom of the right compartment.

When connecting the LP tank to your grill be certain that all connections are tight. Once gas connections are made, test for gas leaks.

On models so equipped, install the two (2) racks provided into the opening by sliding them onto the rollers on the sidewalls of the center cavity.

The FISHER & PAYKEL DCS ADR136 Access Drawers are made from corrosion-resistant and non-magnetic stainless steel. All parts can be cleaned with hot soapy water, rinsed, dried and buffed to a shine with a soft, heavy cloth. Always try this first, as it is the mildest cleaning procedure. Many different stainless steel cleaners are available. Always use the mildest cleaning procedure first, scrubbing in the direction of the grain to avoid marring the surface. The cleaner will be more effective when used in the direction of the grain (polish lines).

Some brands of cleaners of the same type are harsher than others, read their directions. A scent or a propellant can make a difference in the product, read the ingredients. Try on a small area first.

To touch up noticeable scratches in the stainless steel, sand very lightly with wet 100 grit emery paper in the direction of the grain.

Specks of grease can gather on the surfaces of the stainless steel and bake on to the surface and give the appearance of rust. For removal use an abrasive pad (Scotch Brite is good) in conjunction with a stainless steel cleaner. Always rub in the direction of the grain.

Use only clean sponges, soft cloths, paper towels, plastic non-metal soap pads for cleaning or scouring as recommended in this section. (Use only soap pads with soap still in them. An empty pad can scratch.)

Be sure to rinse all parts thoroughly and to wipe dry to avoid water marks.

Stainless steel tends to corrode in presence of chlorides and sulfides especially in coastal areas. To ensure corrosion prevention, wash all stainless steel surfaces every 3-4 weeks with fresh water and stainless cleaner.

After cleaning, use a stainless steel polish, such as Stainless Steel Magic® applied to the drawer and handle surfaces. To maintain the smooth operation of the drawers, spray the bearing areas with silicone spray lubricant annually.

Freezer Pack (optional, Kit #70696A)

Waste Basket Holder (optional, Kit #70906)

Bottom Cover (optional, Kit #70907)