FISHER & PAYKEL DCS ADR124 (01) PDF DOCUMENT

Please adhere to the following safety warnings when using your FISHER & PAYKEL DCS ADR124:

• Do Not store or use gasoline or other flammable vapors and liquids inside or in the vicinity of this or any other appliance.

• An LP cylinder not connected for use shall not be stored inside or in the vicinity of this unit.

• Do not store items of interest to children above or on the inside of any appliance. Children could be seriously injured if they should climb onto or into the appliance to reach these items.

• Closing drawers may cause injury to your hands or fingers. Always use the handles to close or open drawers and be sure to keep hands away from drawer edges.

1. Do not allow children or pets to play in or around the Access Drawers.

2. Clean the Access Drawers regularly using a mild dish washing liquid and water.

3. To maintain the exterior appearance, apply a stainless steel polish to the outside surfaces on a regular basis.

4. Sanitize the Access Drawers surfaces each season as necessary.

5. To prevent the formation of mold or mildew, do not store cloth napkins or tablecloths in the Access Drawers for long periods.

6. Cooking utensils that are stored in the Access Drawers should be stored in sealable plastic bags and/or washed each time before re-use.

7. To prevent personal injury or damage to the drawers, do not overload them. The maximum rating per drawer is 75 pounds.

1. Inspect the Access Drawers to verify that there is no shipping damage. If any damage is detected, call the shipper and initiate a damage claim. DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

2. Operate the drawers to be sure they glide smoothly.

3. Examine the drawer fronts to be sure there are no dents or scratches or discoloring.

Model	D	W	H	F
ADR124	23-1/2″	24″	21-7/8″	2″

• Cabinet face should be clean and flat.

• All angles must be at 90° and plumb.

• Support structure must be resistant to moisture damage.

• All gas lines and plumbing must be done before installing access drawers.

• Do not use any harsh products (acid, solvent, sealers) around this unit.

• Any cabinet and/or ground preparations must be completed prior to installation.

Please use the following dimensions for the installation of your FISHER & PAYKEL DCS ADR124:

CUTOUT DIMENSIONS

Model	A (-0,+1/8″)	B (-0,+1/8″)	C	D
ADR124	22″	20″	1.0″ min.	1.0″ min.

SUPPORT BOARD DIMENSIONS

Model	A	B	C	D	E
24″ (ADR124)	20″	1-1/2″*	3-1/2″ min.	14	–

*Dependent on application. Top of 2×4’s must be 1/2″ above the bottom edge of the cutout.

1. Make a cut-out in your cabinet or island using the specified dimensions. Note that each corner of the cutout should be 90° for the Access Drawers to fit properly. For an island installation, use a minimum of 3 vents providing 10 sq. in. per vent.

2. Place 2x4s to provide support for the Access Drawers structure in the indicated locations.

3. To ensure proper drawer operation, be sure your support boards are flat and level.

4. When installing your support boards, be sure they are level from front to back and side to side.

5. Ensure that the bottom of the center divider rests on top of the support boards.

1. To remove most drawers, pull them out until their slider latch is visible. Carefully push the latch down on the left side while pulling up on the right side and pull the drawers completely out of the frame.

2. To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or table cloth.

3. To remove the FISHER & PAYKEL DCS ADR124 drawer specifically, pull the drawer out and lift the end by the handle to disengage the rollers.

1. With the help of an assistant, lift the unit and slide it into the cabinet cutout. Adjust for level and fit.

2. Locate mounting holes on the frame. Secure the unit using screws suited for the type of cabinet material. Depending on the wall thickness and location of mounting holes, an additional board may be required to properly receive the screws.

1. Re-install the drawers by extending their guides.

2. While holding the drawer parallel to the cabinet, carefully align and engage the ends of the glides. Slide the drawer in about an inch so that the glides are supporting the back of the drawer.

3. While holding the drawer up by the handle, pull the glides from the drawer cavity out over the drawer glide until they click.

4. As you push the drawers in, you will encounter moderate resistance. Continue to push the drawer all the way in to complete the engagement process. The drawer will now glide smoothly in and out with light effort.

1. Your LP tank will be installed in the recess provided in the bottom of the right compartment.

2. When connecting the LP tank to your grill, be certain that all connections are tight. Once gas connections are made, test for gas leaks.

3. On models so equipped, install the two (2) racks provided into the opening by sliding them onto the rollers on the sidewalls of the center cavity.

General Cleaning:

The Access Drawers are made from corrosion-resistant and non-magnetic stainless steel. All parts can be cleaned with hot soapy water, rinsed, dried and buffed to a shine with a soft, heavy cloth. Always use the mildest cleaning procedure first, scrubbing in the direction of the grain to avoid marring the surface.

• Use only clean sponges, soft cloths, paper towels, and plastic non-metal soap pads for cleaning or scouring.

• Be sure to rinse all parts thoroughly and to wipe dry to avoid water marks.

• Note: Stainless steel tends to corrode in the presence of chlorides and sulfides, especially in coastal areas. To ensure corrosion prevention, wash all stainless steel surfaces every 3-4 weeks with fresh water and stainless cleaner.

Touching up Scratches:

To touch up noticeable scratches in the stainless steel, sand very lightly with wet 100 grit emery paper in the direction of the grain.

Removing Grease:

Specks of grease can gather on the surfaces of the stainless steel and bake on to the surface, giving the appearance of rust. For removal use an abrasive pad (like Scotch Brite) in conjunction with a stainless steel cleaner. Always rub in the direction of the grain.

Maintenance:

After cleaning, use a stainless steel polish applied to the drawer and handle surfaces. To maintain the smooth operation of the drawers, spray the bearing areas with silicone spray lubricant annually.

The following optional accessories are available:

1. Freezer Pack (Kit #70696A)

2. Waste Basket Holder (Kit #70906)

3. Bottom Cover (Kit #70907)