EXTREME 5120-24XT-4Y-TAA (01) PDF DOCUMENT

The following tools are needed for installation:

1. #2 Phillips screwdriver (a magnetic screwdriver is recommended)

2. ESD-protective wrist strap

The installation site must meet the following requirements:

• Appropriately grounded power receptacles located within 1.8 m (6 ft.)

• A readily accessible device for disconnecting power, such as a breaker or master switch

• Network cabling within reach

• Ensure that the vent openings on the front panel and the rear fan modules are not blocked for proper ventilation

• Temperature between 0°C (32°F) and 50°C (122°F) – or as noted in “Operating Conditions” – with fluctuations of less than 10°C (18°F) per hour.

After removing the packing material, verify that all of the following components are included:

1. Switch

2. Quick reference guide

3. Accessory box

4. Rack mount ears (2), accessory bag: Rail screws (12), rack screws (6), rack nuts (6)

Console cables can be ordered separately.

The EXTREME 5120-24XT-4Y-TAA can be installed in a standard 19-inch equipment rack. This procedure uses a two-post mounting kit, which accommodates rack posts 3 inches or 6 inches wide. Rack ears can support both flush- and mid-mounting.

1. Attach a mounting bracket to each side of the switch. You can attach the brackets at the front of the switch or at the middle of the switch for front flush-mount, front mid-mount, rear flush-mount, or rear mid-mount configurations.

2. Secure the brackets to the rack posts using rack-mounting screws and nuts that are appropriate for the rack (provided). The switch can be mounted to the two front posts or the two rear posts as shown.

The EXTREME 5120-24XT-4Y-TAA series switches run on AC power. To connect the switch to a primary power source, follow these steps:

1. Connect the AC power cord to the AC power input socket on the power supply and an AC power outlet.

2. When power is connected, verify that the switch’s PWR LED turns green. If the PWR LED does not turn green, refer to the Extreme 5120 Hardware Installation Guide for troubleshooting information.

Note: Installing the system as described meets the protective earth grounding requirements of relevant standards. However, in some cases, it may be necessary to use an alternative grounding method. A 14 AWG wire can be connected between the grounding lug on the chassis and a nearby building ground point.

You should upgrade to a generally available (GA) version of the software before you use the unit. Switch Engine is the default operating system (OS) for the 5120 Series. To connect the switch to the network, upgrade it, and configure it for use, follow the steps in the Extreme 5120 Hardware Installation Guide.

Please observe the following safety notices:

Shock Hazard: Disconnect all power inputs before servicing.

Electrical Hazard: Only qualified instructed or skilled personnel should perform installation, repair, or disassembly procedures.

Power Supplies: Extreme Networks power supplies do not have switches for turning the unit on and off. Before servicing, disconnect all power cords to remove power from the device. Make sure that these connections are easily accessible.

Restricted Access Location: This equipment is designed for installation in restricted access locations and suitable for installation in Information Technology Rooms, not suitable for use in locations where children are likely to be present.

Circuit Breaker: A dedicated Listed circuit breaker rated at 15A is to be used for each power supply connection.

Mounting: Before mounting the device, ensure that the rack can support it without compromising stability. Otherwise, personal injury or equipment damage may result.

ESD: Follow appropriate ESD procedures when unpacking and handling the switch. These include unpacking the switch in an ESD-safe environment and wearing appropriate ESD protective gear, such as ESD-safe footwear and ESD wrist straps where appropriate.

Indoor Use: This unit must be installed indoors. The unit, AC power adapter, and its cables are not designed for outdoor use.

Radiation Exposure: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Laser Output: Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. Use only UL/CSA, IEC/EN60825-1/-2 recognized pluggable modules.

Battery: This product contains a battery used to maintain product information. If the battery should need replacement it must be replaced by Service Personnel. Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in accordance with local disposal regulations.

The hardware components are as follows:

Front Panel Components:

1. 1Gb/10Gb SFP+ ports (1Gb/10GBase-T non-PoE ports for 5120-24XT-4Y)

2. 10Gb/25Gb SFP28 ports

3. Micro-B USB serial console port

4. System LEDs

5. Mode button

6. USB Type A port

7. RJ-45 serial console port

8. 100/1000BASE-T out-of-band management port

9. 100Gb QSFP28 uplink ports

Rear Panel Components:

1. Modular AC power supplies

2. Grounding lug

3. Fan modules

4. Filler panels

Operating Temperature:

0°C (32°F) to 50°C (122°F) up to 3000 m (10,000 ft), front-to-back and back-to-front airflow

One fan failure:

5120-44X-4Y-2C

0°C (32°F) to 50°C (122°F) at sea level and 45°C (113°F) at 3000 m (10,000 ft), front-to-back airflow

0°C (32°F) to 45°C (113°F) at sea level and 40°C (104°F) at 3000 m (10,000 ft), back-to-front airflow

5120-24X-4Y

0°C (32°F) to 50°C (122°F) at sea level and at 3000 m (10,000 ft), front-to-back airflow

0°C (32°F) to 50°C (122°F) at sea level and 45°C (113°F) at 3000 m (10,000 ft), back-to-front airflow

5120-24XT-4Y

0°C (32°F) to 50°C (122°F) up to 3000 m (10,000 ft), front-to-back and back-to-front airflow

Storage Temperature:

-40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity:

5% to 95% (non-condensing)

Each Extreme 5120 Series switch includes a Micro-B USB serial console port, an RJ-45 serial console port, a 100/1000BASE-T out-of-band management port, and a USB Type A storage port. 5120 Series switches are pre-loaded with the Switch Engine OS.

The following table lists the specific interfaces for each switch model:

5120-44X-4Y-2C (base)	Stackable switch with 44 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 2 100Gb QSFP28 Universal/stack/uplink ports, 6 empty fan slots, and 2 empty modular power supply unit slots.
5120-44X-4Y-2C-AC-F	Stackable switch with 44 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 2 100Gb QSFP28 Universal/stack/uplink ports, 6 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow.
5120-44X-4Y-2C-AC-R	Stackable switch with 44 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 2 100Gb QSFP28 Universal/stack/uplink ports, 6 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Back-to-front airflow.
5120-44X-4Y-2C-TAA (base)	Stackable switch with 44 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 2 100Gb QSFP28 Universal/stack/uplink ports, 6 empty fan slots, and 2 empty modular power supply unit slots. TAA compliant.
5120-44X-4Y-2C-AC-F-TAA	Stackable switch with 44 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 2 100Gb QSFP28 Universal/stack/uplink ports, 6 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow. TAA compliant.
5120-24X-4Y (base)	Stackable switch with 24 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 4 empty fan slots, and 2 empty modular power supply unit slots.
5120-24X-4Y-AC-F	Stackable switch with 24 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow.
5120-24X-4Y-AC-R	Stackable switch with 24 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Back-to-front airflow.
5120-24X-4Y-TAA (base)	Stackable switch with 24 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 4 empty fan slots, and 2 empty modular power supply unit slots. TAA compliant.
5120-24X-4Y-AC-F-TAA	Stackable switch with 24 1Gb/10Gb SFP+ ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow. TAA compliant.
5120-24XT-4Y (base)	Stackable switch with 24 1Gb/10GBase-T non-PoE ports, 4 10Gb/25Gb SFP28 ports, 4 empty fan slots, and 2 empty modular power supply unit slots.
5120-24XT-4Y-AC-F	Stackable switch with 24 1Gb/10GBase-T non-PoE ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow.
5120-24XT-4Y-AC-R	Stackable switch with 24 1Gb/10GBase-T non-PoE ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Back-to-front airflow.
5120-24XT-4Y-TAA (base)	Stackable switch with 24 1Gb/10GBase-T non-PoE ports, 4 10Gb/25Gb SFP28 ports, 4 empty fan slots, and 2 empty modular power supply unit slots. TAA compliant.
5120-24XT-4Y-AC-F-TAA	Stackable switch with 24 1Gb/10GBase-T non-PoE ports, 4 10Gb/25Gb SFP28 ports, 4 fans, 1 modular AC power supply unit, and 1 empty modular power supply unit slot. Front-to-back airflow. TAA compliant.

XN-ACPWR-550W-FB-A	550W AC power supply with front-to-back airflow for 5120 Series switches.
XN-ACPWR-550W-BF-A	550W AC power supply with back-to-front airflow for 5120 Series switches.
XN-FAN-005-F	Fan module with front-to-back airflow for 5120 Series switches.
XN-FAN-005-R	Fan module with back-to-front airflow for 5120 Series switches.

XN-2P-RMKIT-014

Two-post rack mount kit for 5120 Series switches for use with two- or four-post racks.

All models

AC Input: 100-120/200-240 VAC, 50-60 Hz, 2.5/1.2 A Max. for each PSU