DREAME DREAMEBOT L10 PRIME RCWC1 (01) PDF MANUAL

This product should not be used by children younger than 8 years old nor persons with physical, sensory, intellectual deficiencies, or limited experience or knowledge without the supervision of a parent or guardian to ensure safe operation and to avoid any risks. Cleaning and maintenance shall not be performed by children without supervision.

This product is for floor cleaning in a home environment only. Do not use it outdoors, on non-floor surfaces, or in a commercial or industrial setting.

Do not use the robot in an area suspended above ground level without a protective barrier.

Do not place the robot upside down. Do not use the LDS cover, robot cover, or bumper as a handle for the robot.

Do not use the robot at an ambient temperature above 40°C or below 0°C or on a floor with liquids or sticky substances.

To prevent damage or harm from dragging, clear any loose objects from the floor, and remove cables or power cords on the cleaning path before operating the appliance.

Remove fragile or small items from the floor to prevent the robot from bumping into and damaging them.

Keep hair, fingers, and other body parts away from the suction opening of the robot.

Do not operate the appliance in a room where an infant or child is sleeping.

Do not place children, pets, or any item on top of the robot regardless of whether it is stationary or moving.

Do not vacuum hard or sharp objects. Do not use the appliance to pick up objects such as stones, large pieces of paper or any item that may clog the appliance.

Do not wipe the robot or the base station with a wet cloth or rinse them with any liquid. After cleaning washable parts, fully dry the parts before reinstalling and using them.

The appliance is only to be used with the power supply unit provided with the appliance.

This appliance contains batteries that are only replaceable by skilled persons.

If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

Do not use any third-party battery or base station. The robot can only be used with the model RCWC1 base station.

Do not attempt to disassemble, repair, or modify the battery or the base station on your own.

Do not place the base station near a heat source.

Do not use a wet cloth or wet hands to wipe or clean the base station’s charging contacts.

If the power cord becomes damaged or broken, stop using it immediately and contact after-sales service.

If the robot will not be used for an extended period of time, fully charge it, then turn it off and store it in a cool, dry place. Recharge the robot at least once every 3 months to avoid over-discharging the battery.

Do not improperly dispose of old batteries. Unneeded batteries should be discarded at an appropriate recycling facility.

The lithium-ion battery pack contains substances that are hazardous to the environment. Before disposing of the robot vacuum, please first remove the battery pack, then discard, or recycle it in accordance with local laws and regulations of the country or region it is used in.

When removing the batteries from the product, it is better to use up the batteries and make sure your product is disconnected from power.

1. Uninstall the screw on the bottom, then remove the cover.

2. Unplug the battery connector, then remove the batteries. Do not damage the battery case to avoid any risk of injuries.

3. Return the batteries to a professional recycling organization.

The laser sensor in this product meets the IEC 60825-1: 2014 Standard for Class 1 laser products. Please avoid direct eye contact with it during use.

Spot Cleaning Button: Press briefly to start spot cleaning.

Power / Clean Button:

Press and hold for 3 seconds to turn on or off.

Press briefly to start cleaning after the robot is turned on.

Dock Button:

Press briefly to send the robot back to the base station.

Press and hold for 3 seconds to disable Child Lock.

Reset Button (Under the Cover): Press and hold for 3 seconds to restore to factory settings.

Status Indicator:

Solid White: Cleaning or cleaned.

Quickly Blinking Orange: Error.

Solid Orange: Low battery or paused.

Note: Press any button to pause the robot while it is cleaning or returning to charge.

Status Indicator:

Solid white: The base station is connected to power.

Blinking Orange: The base station has an error.

1. Remove the protective strips from the robot.

2. Install the side brush until it clicks into place.

1. Place the base station in a location that is as open as possible with a good Wi-Fi signal. It should have more than 1.5m clearance in front and more than 5cm on each side.

2. Insert the power cord into the base station and plug it into the socket. Firmly insert the power cord upwards until the indicator turns on.

Note:

Make sure that no objects might block the signaling area.

To prevent water stains from damaging wood floors or carpets, it is recommended to place the base station on tile or marble floors.

Press and hold the Power button on the robot for 3 seconds to turn it on. Place the robot onto the base station with the mop assembly facing toward the washboard. You will hear a voice notification when the robot successfully connects to the base station and starts charging.

Note: It is recommended to fully charge the robot before its first use. When the robot cannot be turned on after the battery is depleted, manually connect the robot with the station to charge it.

Take out the clean water tank from the base station, and fill it with clean water up to the max water line. Then install it back into the base station.

Note:

Do not fill the water tank with hot water as this may cause the water tank to warp.

Do not add any liquid other than the officially-approved cleaning solution to help prevent base station malfunction.

1. Scan the QR code on the robot, or search for “Dreamehome” in the app store to download and install the app.

2. Open the Dreamehome App, tap “+” in the upper right corner, and scan the QR code on the robot to add “DreameBot L10 Prime”. Follow the prompts to finish the Wi-Fi connection.

Note: Only 2.4GHz Wi-Fi is supported.

Blinking slowly: To be connected

Blinking quickly: Connecting

On: Connected

Simultaneously press and hold the Spot Cleaning and Dock buttons until you hear a voice prompt say, “Waiting for the network configuration.” Once the Wi-Fi indicator is blinking slowly, the Wi-Fi has been successfully reset.

After configuring the network for the first time, follow the instructions on the app to quickly create a map. The robot will start mapping without cleaning. When the robot returns to the base station, the mapping process has been completed and the map will be saved automatically.

Press and hold the Power button for 3 seconds to turn on the robot. The power indicator should be illuminated. Place the robot onto the base; the robot should turn on automatically and begin charging. To turn off the robot, move the robot away from the base and press and hold the Power button for 3 seconds.

When the robot is running, press any button to pause it.

If the robot is paused for more than 10 minutes, it automatically enters sleep mode. The power indicator and charging indicator will turn off. Press any button on the robot or base, or use the app to wake up the robot.

Note:

The robot will turn off automatically if it is left in sleep mode for more than 12 hours.

If the robot is paused and placed onto the base station, the current cleaning process will end.

When the robot is set to the Do Not Disturb (DND) mode, the robot will be prevented from resuming cleaning and the power indicator will go out. The DND mode is disabled by default at the factory. You can use the app to enable the DND mode or modify the DND period. The DND period is 22:00-8:00 by default.

Note:

The scheduled cleaning tasks will be performed on time during the DND period.

The robot will resume cleanup where it left off after the DND period expires.

When the robot is on standby, briefly press the Spot Cleaning button to enable spot cleaning mode. In this mode, the robot will clean a square-shaped area of 1.5 x 1.5 meters around it and return to its starting point once spot cleaning is completed.

If the robot stops responding or cannot be turned off, press and hold the Power button for 10 seconds to force a shutdown. Then press and hold the Power button for 3 seconds to turn the robot back on.

Press the Power button on the robot, or use the app to make the robot start from the base station. Then the robot will plan the optimal cleaning route and perform the cleaning task based on the created map. The mop pads will be cleaned before the robot starts mopping.

When mopping, the robot will automatically return to the base station to wash its mop pads based on the mop pad cleaning frequency specified in the app.

To use only the sweeping function, select “Sweeping” in the app, and the robot will automatically lift the mop assembly before sweeping. Or you can remove the mop assembly and then the robot will automatically switch to the sweeping mode.

Part	Maintenance Frequency	Replacement Period
Used Water Tank	After each use	/
Dust Bin	As needed
Clean Water Tank
Main Brush	Once every 2 weeks	Every 6 to 12 months
Dust Bin Filter		Every 3 to 6 months
Side Brush
Mop Pad	/	Every 1 to 3 months

1. Remove the used water tank, open its cover and pour out the dirty water.

2. Rinse the used water tank with clean water, and use a proper tool to clean its inner wall.

Note: The float ball in the used water tank is a movable part. Do not apply too much force when cleaning it to avoid damaging it.

1. Press the brush guard clips inwards to remove the brush guard and lift the brush out of the robot.

2. Pull out the brush covers. Use a proper tool to remove the hair tangled in the brush.

3. Remove and clean the side brush.

4. Use a tool such as a small screwdriver to separate the axle and tire of the universal wheel. Do not use excessive force.

5. Rinse the universal wheel under the running water and put it back after drying it completely.

1. Remove the filter and tap its basket gently. Do not attempt to clean the filter with a brush, finger, or any sharp objects so as to avoid damaging it.

2. Rinse the dust bin and filter with water and dry them completely before reinstalling.

Note: Rinse the dust bin and filter with clean water only. Do not use any detergent. Use the dust bin and filter only when they are completely dry.

Wipe the following sensors and charging contacts of the robot by using a soft, dry cloth: Cliff Sensors, Laser Distance Sensor (LDS), Edge Sensor, Bumper, Carpet Sensor, and Charging Contacts.

Clean the charging contacts and the signaling area of the base station with a soft, dry cloth.

Remove the mop pad from the mop pad holder to replace it.

The robot contains a high-performance lithium-ion battery pack. Make sure that the battery remains well-charged for daily use to maintain optimal battery performance. If the robot is not used for an extended period of time, turn it off and put it away. To prevent damage from over-discharging, charge the robot at least once every three months.

The battery may be low. Recharge the robot on the base and try again.

The temperature of the battery is too low or too high. It is recommended to operate the appliance at a temperature between 32 °F (0°C) and 104 °F (40°C).

The base station may not be receiving power. Please confirm that both ends of the power cord are plugged in correctly.

The robot may be in poor contact with the charging contacts. Clean the charging contacts on both the base station and the robot.

Check whether there is any foreign object at the connector of the robot and remove the foreign object if any.

The password of Wi-Fi may be incorrect. Please enter the correct password.

You may be connected to a 5GHz Wi-Fi band, which is not supported. Please ensure your robot is connected to a 2.4GHz band.

The Wi-Fi signal may be weak. Make sure the robot is in an area with good Wi-Fi coverage.

The robot may not be ready to be configured. Please exit and re-enter the app, and then try again as instructed.

The base station may be disconnected from power or may have been moved when the robot is not on it.

There may be too many obstructions around the base station. Place the base station in a more open area.

Moving the robot may cause it to re-position itself, and it will recreate a map if re-positioning fails. If the robot is too far from the base station, it might not be able to automatically return on its own, in which case you will need to manually place the robot onto the base station.

Wipe the signaling area on the base station to remove dust or debris.

The robot cannot be turned off when it is charging. It is recommended to move the robot from the base station, and then press and hold the power button for three seconds to turn it off.

If the robot cannot be turned off by performing the step above, press and hold the Power button for 10 seconds to forcibly turn off the robot.

It takes about 6 hours to fully charge the robot when its battery is low.

If you operate the robot at temperatures outside of the specified range, the charging speed will automatically slow down to extend the battery life.

The charging contacts on both the robot and the base may be dirty, please wipe them with a dry cloth.

Check whether the dust bin filter is clogged. If so, clean it or replace it.

A hard object may be caught in the multi-surface rubber brush or the dust bin. Check and remove any hard object.

The main brush or the side brush may become tangled. Check and remove any foreign objects.

Switch the suction mode to Standard or Quiet.

Objects such as power cords and slippers should be organized before using the robot.

Working on wet slippery surfaces may cause the main wheel to slip. It is recommended to dry the wet places before using the robot.

Make sure that the doors of the rooms to be cleaned are open.

Check whether there is a threshold higher than 2 cm at the door of the room. The robot cannot climb over high thresholds or steps.

The place in front of the room to be cleaned may be wet and slippery, causing the robot to work abnormally. It is recommended to dry the floor before using the robot.

Check whether the seal on the used water tank is loose or not correctly installed. Manually reset it if so.

Gently press down on the used water tank to make sure it is installed correctly.

Remove the washboard and check whether the sewage drain is blocked and clean it.

Check the cleaning solution. Do not add any liquid other than the officially-approved cleaning solution.

Model	RLL11GC
Charging Time	Approx. 6 hours
Rated Voltage	14.4 V
Rated Power	60 W
Operation Frequency	2400-2483.5 MHz
Maximum Output Power	<20 dBm

Model	RCWC1
Rated Input	100-240 V~ 50-60 Hz
Rated Output	20 V 1 A
Rated Power	30 W