DJI NEO (02) PDF Document

Tutorial videos for the DJI NEO can be accessed by scanning the QR code provided in the Quick Start Guide. These videos provide visual instructions on how to operate and set up your aircraft.

The DJI NEO requires the DJI Fly app. You can download this application by scanning the QR code found in the documentation provided with your device.

The user manual for the DJI NEO is available digitally. You can access it by scanning the QR code located in the first section of the Quick Start Guide.

To remove the gimbal protector from the DJI NEO, follow these steps:

1. Locate the gimbal protector on the front of the aircraft.

2. Press down on the designated area of the protector as shown in the diagram.

3. Carefully pull the protector away from the gimbal to remove it.

The Intelligent Flight Battery for the DJI NEO must be charged before it is used for the first time. Charging the battery is necessary to activate it, as batteries are shipped in a hibernation mode for safety.

The DJI NEO Intelligent Flight Battery should be charged using a power source that meets specific requirements. Refer to the table below for power specifications:

To power on the DJI NEO, perform a specific button sequence: press the power button once, and then immediately press and hold the button for more than 2 seconds.

To power off the DJI NEO, use the same sequence as powering on: press the power button once, and then press and hold the button for more than 2 seconds.

To connect and activate your DJI NEO, follow these steps within the mobile app:

1. Open the DJI Fly app on your mobile device.

2. On the home screen, tap the Connection Guide located in the bottom right corner.

3. Select the DJI NEO aircraft model from the list.

4. Follow the on-screen instructions provided by the app to complete the connection and activation process.

By default, the Palm Control feature on the DJI NEO is set to Follow Mode.

Palm Control on the DJI NEO involves a four-step process for takeoff and flight:

Step 1: Position the DJI NEO on your flat palm in front of you while standing in an open area.

Step 2: Ensure you are facing the camera and hold your hand steady. Wait for approximately 2 seconds for the aircraft to recognize the command.

Step 3: The DJI NEO will start its motors and take off from your palm into a hover.

Step 4: The aircraft will then enter Follow Mode, where it will track and follow your movements automatically.

During Palm Control for the DJI NEO, there is a recognition period indicated in the instructions as taking 2 seconds. Once recognized, the aircraft initiates takeoff.

The power button for the DJI NEO is located on the top of the aircraft body, positioned between the status indicators and the battery compartment.

The DJI NEO features a fully shielded design with four integrated propeller guards that encircle each of the four propellers for enhanced safety during palm takeoffs and landings.

The DJI NEO requires a charger with a minimum power output of 10 Watts (5V, 2A) to properly activate and charge the Intelligent Flight Battery.

Yes, the DJI NEO supports Palm Control, which allows you to perform basic flight operations like takeoff and following without a dedicated remote controller, using only your hand gestures and the camera’s tracking capabilities.

If your DJI NEO does not power on, ensure that the Intelligent Flight Battery has been activated by charging it with a power source of at least 10W (5V, 2A). Also, verify you are using the correct button sequence: a short press followed by a long press of 2 seconds.

Yes, the DJI NEO includes Follow Mode as the default setting when using the Palm Control feature.

The documentation provided for the DJI NEO is the Quick Start Guide version 1.0.

Yes, the DJI NEO comes with a gimbal protector that must be removed before flight to allow the gimbal and camera to move freely.

After entering the Connection Guide in the DJI Fly app, a list of aircraft will appear. You must scroll or search to find and select the DJI NEO from this list to proceed with the setup.

To perform a palm takeoff with the DJI NEO:

1. Place the aircraft on your open palm.

2. Look toward the camera so the DJI NEO can identify the user.

3. Wait for the 2-second recognition period.

4. The motors will start, and the aircraft will lift off from your hand.

Technical support for the DJI NEO can be obtained by scanning the Contact DJI Support QR code found in the “We Are Here For You” section of the guide.

Latest content and downloads for the DJI NEO can be found by scanning the QR code located near the download section of the Quick Start Guide.

The diagrams of the DJI NEO show a quadcopter configuration with four propellers housed within protective guards. While the Quick Start Guide does not detail replacement, they are standard components of the aircraft.

This icon instructs the user to interact with the mobile screen. Specifically, for the DJI NEO, it indicates where to tap the Connection Guide on the home screen of the DJI Fly app.

Once the DJI NEO has taken off from the palm and entered Follow Mode, it uses its onboard sensors and camera to maintain a set distance and orientation while tracking the user as they walk or move.

Yes, the camera of the DJI NEO should be facing the user during the recognition phase (Step 2 of Palm Control) to ensure the aircraft can successfully lock onto the user before taking off.

This symbol indicates that the charger used for the DJI NEO must provide at least 10 Watts of power. Using a charger with lower wattage may result in the battery failing to activate or charging very slowly.

No, the DJI NEO cannot be used immediately. You must first remove the gimbal protector and charge the Intelligent Flight Battery to activate it and the aircraft.

The status lights for the DJI NEO are located on the top of the aircraft near the power button. These LEDs indicate the battery level and the current status of the aircraft.

When using Palm Control, the DJI NEO enters Follow Mode automatically by default after it takes off from your hand and identifies you as the subject.

You should hold the DJI NEO on a flat, level palm. Your hand should be steady and held at a height where the camera can clearly see your face.

No, the DJI NEO is activated through the DJI Fly app on a compatible mobile device using the Connection Guide provided in the software.

Open the DJI Fly app, go to the home screen, and look for the “Connection Guide” in the bottom right corner. Tapping this will open the model selection menu where the DJI NEO is listed.

During these 2 seconds, the DJI NEO camera system performs subject recognition. Once the aircraft has identified the user, it prepares the motors for takeoff.

Yes, based on the charging and power diagrams, the Intelligent Flight Battery is a distinct component that is inserted into the rear of the DJI NEO aircraft.

The DJI NEO Palm Control instructions show the aircraft being used in an open outdoor environment with trees and space. It is recommended to use these modes in areas with sufficient space for the aircraft to move safely.

When inserting the battery into the DJI NEO, ensure it is pushed all the way in until it clicks or aligns with the rear housing, as shown in the charging diagram.