CHANNEL MASTER CM-3001HD (01) PDF Document

Step 1. Connect one end of the blue-banded coaxial cable to the corresponding blue-colored connector (“ANT”) on the power supply. Connect the other end of the blue-banded cable to the connector at the bottom of the body of the antenna.

Step 2. Connect one end of the yellow-banded coaxial cable to the corresponding yellow-colored connector (“TV”) on the power supply. Connect the other end of the yellow-banded cable to your television, set-top box, or DVR.

Step 3. Use tape to temporarily attach the SMARTenna+ to the desired location. Ideal placement is on a wall or in a window, facing the direction of the broadcast towers in your area.

Step 4. Plug the SMARTenna+ power supply into an electrical outlet. After plugging it in, move to the position (on a couch, in a chair, etc.) at which you will normally watch TV. The SMARTenna+ will run a scan for approximately 2 minutes to optimize the antenna settings.

During the scanning period, the LED on the antenna will blink continuously. Remain at your preferred viewing location during this initial scan to allow the antenna to account for radio wave reflections caused by objects or people. Do not stand in front of the antenna during the scanning period. Once the scan is complete, the LED will turn a solid color.

Note: If the antenna is moved during the scanning period (blinking LED) or during normal operation (solid LED), it will need to be unplugged or reset to repeat the scanning process.

Step 5. After the SMARTenna+ scanning is complete, ensure your television, set-top box, or DVR is set to scan for Antenna channels, NOT CABLE. You will need to choose the option that says Antenna, Air, or Broadcast. Once your device is set, proceed with the Auto Channel Scan.

Step 6. Once desired performance is achieved and you have checked that all desired channels are being received, permanently attach the antenna using the included adhesive tabs.

Once the Channel Scan on your TV or converter box is complete, check to make sure all desired channels are being received. If you think you are missing a channel, repeat the setup steps in an alternative location and then rescan for channels on your device.

The CHANNEL MASTER CM-3001HD comes with 7 different selectable antenna modes to fine-tune reception if you are not getting optimal performance after the initial scan.

The antenna is automatically set to operate in Mode 1 by default.

To switch to other Modes, quickly press the button on the bottom of the antenna to select the other modes: 2 quick pushes for Mode 2, 3 quick pushes for Mode 3, and so forth, up to 7 pushes for Mode 7.

After making your mode selection, the LED will quickly flash to indicate the antenna mode selected – 2 flashes indicate Mode 2, 3 flashes indicate Mode 3, and so on.

To return to Mode 1, quickly push the button a single time.

Note: When using alternate antenna Modes, you can optionally re-run the channel scan on your TV to see if additional channels can be picked up.

To RESET the CHANNEL MASTER CM-3001HD antenna, hold down the button at the bottom of the antenna for at least 5 seconds, and then release the button.

Installation

• Ground the installation in accordance with NEC® or other applicable codes.

• Locate the power adapter and receiver indoors in an open, well-ventilated area. Do not place them in an enclosure (such as a cabinet) without proper ventilation.

• Place the receiver on its feet on a firm, stable, horizontal surface.

• Unplug the power adapter from the power socket during installation and follow all connection instructions.

• Only connect the original power adapter to the receiver. Other power adapters may damage the circuitry and cause a fire risk.

• DO NOT place heavy objects on the receiver or power adapter.

• Keep plastic packaging and small parts away from babies and children.

Protect from Water

• DO NOT place objects filled with liquids, such as vases or drinks, on or near the power adapter or receiver.

General Precautions

• DO NOT remove the power adapter cover due to risk of electric shock from live parts inside.

• DO NOT allow objects to drop or be pushed inside the receiver, for example by children.

• DO NOT place naked flames such as lighted candles on or near the receiver or power adapter.

Equipment Care

• Unplug the power adapter from the power socket before cleaning.

• If the power adapter or receiver is damaged, unplug it from the power socket and have it checked by qualified personnel before operating it any further.

If you are within 50 miles of broadcast towers, not receiving any channels is very rare and is typically a setup issue or a cause of obstructive materials such as buildings or trees. Double-check your connections and confirm that your television is set to scan for antenna channels and not cable channels.

Indoor reception can be challenging in certain building types. Try repositioning the CHANNEL MASTER CM-3001HD SMARTenna+ and repeating the setup process. If you continue to experience problems you may need to upgrade to an outdoor antenna.

It is recommended to mount the CHANNEL MASTER CM-3001HD SMARTenna+ at a high position such as near the ceiling, or on a nearby window, in order to enable the best performance.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Do not make changes or modifications to this equipment. This could void the user’s authority to operate the equipment.