BEYERDYNAMIC AMIRON 300 (01) PDF MANUAL

Only use the AMIRON 300 earphones as described in this manual.

Please observe the relevant country-specific regulations before using the product.

Do not use the AMIRON 300 earphones when they are damaged.

High volume levels over longer listening periods can permanently damage your hearing.

Before using the AMIRON 300 earphones, set the volume to minimum.

Only increase the volume after positioning the AMIRON 300 earphones.

Do not use the AMIRON 300 earphones at high volume for a long period. When listening and speaking normally using AMIRON 300 earphones, your own voice should still be perceptible.

In case of tinnitus, reduce the volume. If necessary, consult a doctor.

Always ensure an adequate volume level. It is advisable to keep listening periods as short as possible at high volume levels.

The AMIRON 300 earphones drastically reduce the perception of ambient noise. Using the AMIRON 300 earphones in road traffic can be potentially dangerous. The user’s hearing must not be impaired to the extent that it causes road safety risks.

Do not use the AMIRON 300 earphones within the action area of potentially dangerous machines and tools.

Avoid using the AMIRON 300 earphones in situations where hearing must not be impaired – particularly in road traffic, when crossing a level crossing or on a construction site.

Danger from heat, water and mechanical stress: Excessive heat, water and mechanical stress may cause explosion, heat, fire, smoke or fumes. Injuries and irreversible damage to the battery may result.

Do not expose the battery to excessive heat, fires or extremely low air pressure. There is a risk of explosion, fire, smoke or gas.

Do not subject the battery to mechanical stress such as crushing. This may lead to irreversible damage to the battery, explosion or injuries.

Do not open the housing or disassemble/replace the battery.

Only use a USB 2.0/3.0 standard compliant 5 V power supply unit to charge the battery via the integrated USB socket type C.

Earphones left and right (L / R)

One pair of size “M” eartips mounted on the earphones

Charging case

5 pairs of eartips (XS, S, M, L, XL)

USB cable

Quick Start Guide and Compliance Booklet

For an optimum fit and sound quality, five pairs of silicone eartips in different sizes are included. A good sound and effective ANC (Active Noise Cancellation) is only ensured with suitable eartips.

1. Choose the eartips to ensure the best fit for your ears. You may require different sizes for both ears.

2. To use the eartips, carefully slip them over the AMIRON 300 nozzle.

3. Insert the earphone into your ear with a slight clockwise twisting motion.

4. Make sure that the earphone fits as shown.

If you are using them regularly, we recommend changing the eartips every three months.

We recommend that you only charge the battery with the supplied USB cable. Please fully charge the batteries in the charging case and earphones before using the AMIRON 300 for the first time.

1. Insert the earphones into the charging case and close the lid.

2. To charge the case, connect the USB cable to charge.

3. Alternatively, you can place the charging case on a wireless charging station.

When the battery of the charging case is fully charged, the LED on the charging case changes from steady white to red for 4 seconds and then turns off. The earphones are charged when closing the lid.

If the battery of the charging case is empty, the LED will flash red for four times when the lid is open or closed.

When fully charged, disconnect the USB cable from the charging case and the product.

CAUTION! High temperatures, especially with a high charge level, can cause irreversible damage.

If the battery is not used or is stored for extended periods of time, it is recommended to charge it to approx. 50% and store it at no more than 20°C.

Switch off the battery-powered product after use.

Before you use AMIRON 300, you must connect it to a mobile phone or other Bluetooth-enabled device.

1. AMIRON 300 automatically enters pairing mode when the charging case is open. AMIRON 300 can also be put into pairing mode by the following options:

a. Put both earphones into the charging case.

b. Press and hold the pairing button (next to the USB port) for 5 seconds until the LEDs of the earphones flash red and white alternately.

2. Select “beyerdynamic AMIRON 300” from the pairing list of the playback device.

Notes:

When you open the charging case for the first time, AMIRON 300 will be automatically in pairing mode.

When you place the earphones back into the charging case and close the lid, they will disconnect automatically.

The earphones will connect to the last connected device when you open the charging case.

If your earphones are connecting to a device and you want to add a new device, place the earphones into the charging case. Keep the lid open, press and hold the button of the charging case for 5 seconds to put the earphones into the pairing mode. Select “beyerdynamic AMIRON 300” in the pairing list on the new device. The earphones can connect to two devices at the same time.

When the earphones are beyond Bluetooth® pairing distance, they will be disconnected. If they are back in reach within 3 minutes, they will automatically restore the connection, otherwise you have to connect manually.

While the earphones are in the charging case, press and hold the button on the charging case for approx. 12 seconds. The earphone LEDs are steady red and white for 2 seconds, then steady red for 1 second.

AMIRON 300 will automatically power on when you open the charging case.

AMIRON 300 will automatically power off when you place the earphones in the case and close the lid.

Start / pause playback: Tap the touch pad once to start or stop playback.

Next track: Tap the touch pad of the right (R) earphone three times to play the next track.

Previous track: Tap the touch pad of the left (L) earphone three times to play the previous track.

Tap the touch pad twice to switch between ANC on, Transparency on, ANC off.

Tap the touch pad twice and hold with the second touch to activate the voice assistant.

Tap and hold the touch pad of the right or left earphone until the desired volume is reached (only works if you are using both earphones).

Increase volume: Right earphone (R): Press and hold the touch pad to increase the volume.

Reduce volume: Left earphone (L): Press and hold the touch pad to decrease the volume.

Tap the touch pad once to accept an incoming call or to switch between two active calls.

Tap the touch pad twice to hang up.

Tap the touch pad twice to reject an incoming call.

No call active	Operation
Accept incoming call	Tap once
Reject incoming call	Tap twice
End active call	Tap twice

Call already active	Operation
Accept incoming call and hold active call	Tap once
Reject second incoming call	Tap twice
Switch between two calls	Tap once
End active call and switch to held call	Tap twice

When resetting to factory settings, all personal data is deleted!

While the earphones are in the charging case, press and hold the button on the charging case for approx. 12 seconds. The earphone LEDs are steady red and white for 2 seconds, then steady red for 1 second.

To pair new earphones (e.g. when replacing defective or lost earphones), place both earphones into the charging case, and close the lid for at least 10 seconds. Both earphones will pair automatically.

Earphones in ear

Function	Operation (earphones)
Start / stop media playback	Tap once
Switch between noise cancellation (ANC) and transparency mode	Tap twice
Activate voice assistant	Tap twice and hold with the second tap
Accept incoming call	Tap once
Reject incoming call / end active call	Tap twice
Increase volume	Tap and hold right
Reduce volume	Tap and hold left

Both earphones in the charging case

Function	Operation (charging case)
Switch to pairing mode	Open the lid, press and hold the button for 5 s
Reset to factory settings	Press and hold the button approx. 12 s; the pairing list will be also deleted

Charging case LED display

Status	Indication
Being charged via USB: 0 – 20%	Steady red
Being charged via USB: 21 – 69%	Flashes red each 5 s
Being charged via USB: 70 – 100%	Steady white
Being charged via USB: Full	Changes from steady white to red for 4 s, then turns off
Not being charged (open/close lid): 0 – 20%	Flashes red 4 times
Not being charged (open/close lid): 21 – 100%	Flashes white 4 times

Earphones LED display

Status	Indication
Switched on but not connected to a device (pairable, pairing record exists)	LEDs flash white slowly
Switched on but not connected to a device (in pairing mode)	LEDs flash red and white
Switched on and connected to a device	LEDs flash red slowly
Battery below 20%	No LED display – there is a low battery voice prompt
Charging	No LED display
Battery fully charged	No LED display

Due to dirty eartips and the formation of a warm and humid climate in the ear canal, an increased germ level can lead to a higher risk of ear canal infections. Therefore, please clean the eartips regularly.

Remove the eartips from the housing.

Clean the eartips under running lukewarm water and a little ph-neutral soap or with a soft, lint-free moistened cloth.

Remove any cerumen that may be inside the eartip with a cotton bud.

Then rinse off the soap and dry the eartips with a lint-free cloth or leave them to dry overnight.

Only attach the eartips when they are completely dry so that no remaining liquid can enter the electronics of the earphone.

Clean the housing of the earphone with a soft, lint-free cloth. If necessary, you can moisten the cloth slightly with lukewarm water. Make sure that no liquid can enter the housing.

Do not use any solvent-based cleaners, as these will damage the surface.

If you want to remove cerumen from the housing, make sure that you do not rub it into the small openings for pressure equalisation and the microphones.

When you clean the cerumen protective grid (e.g. with a cotton bud or brush), the cerumen should be dry and the protective grid should point to the floor so that loosened cerumen residue does not fall into the earphone.

The symbol on the product, in the operating instructions or on the packaging means that electrical and electronic devices must be disposed of separately from household waste at the end of their life cycle.

Always dispose of used equipment in accordance with applicable regulations.

Battery disposal:

Dispose of batteries separately from the product after use in accordance with the applicable regulations. They must not be disposed of with household waste. Returning batteries is free of charge.

Discharge the batteries before disposal.

Non-destructive removal of the battery by the end user is not possible with this product. Please contact beyerdynamic or consult independent specialists.

If the earphones won’t switch on, the battery is likely empty or almost empty. Please charge the battery.

If there is no audio output, it means there is no Bluetooth® connection. Please pair the AMIRON 300 with your player.

If the AMIRON 300 does not appear in your Bluetooth® device list, check the following:

Ensure the AMIRON 300 is turned on.

Make sure the AMIRON 300 is in pairing mode.

If there is an existing Bluetooth® connection to another player, disconnect that connection and then connect the AMIRON 300 to the desired device.

If the playback volume is too low, the received audio signal is too low. Increase the playback volume on the player to maximum.

If the sound quality is poor, the sealing of the earphone is not sufficient. Select suitable eartips on the right and left until the sound is ideal.

If you are experiencing connection issues, there may be interferences with other devices.

Move away from WLAN routers and microwave ovens.

Make sure that your body is not between the player and the AMIRON 300.