AMAZON BASICS B07V6Z97QJ (01) PDF DOCUMENT

When using the AMAZON BASICS B07V6Z97QJ chair, basic safety precautions should always be followed to reduce the risk of injury:

• For domestic and office use only.

• A competent adult must assemble this product.

• Keep children and pets away while assembling up the product.

• Always use on a firm, level ground.

• Do not use this product if any parts are missing, damaged or worn.

• To avoid scratching the floor, assemble the product on a soft surface, such as a carpet.

• Do not overtighten the fasteners (hardware).

• Regularly examine the product for wear and tear. Replace at first sign of damage or if parts become detached.

• Assemble the product in a spacious area, preferably on a carpet, near the place where the unit is to be located.

• Do not stand on the seat. Do not sit on the armrest.

• The gas lift must be replaced and/or repaired by a qualified professional only.

• Keep all sharp objects away from the upholstery.

• Before first use, check the product for transport damages.

• DANGER Risk of suffocation! Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocation.

The title of the product states a capacity of 300 lbs (136 kg). The Important Safeguards section notes that the product is intended for users up to 265 lbs (120 kg).

The following parts are included for the assembly of your AMAZON BASICS B07V6Z97QJ chair:

• A: Casters (5x)

• B: Base (1x)

• C: Gas Lift (1x)

• D: Seat Mechanism (1x)

• E: Armrests (2x)

• F: Backrest (1x)

• G: Seat Cushion (1x)

• H: Screws 1/4″ x 7/8″ (4x)

• I: Screws 5/16″ x 1-1/4″ (4x)

• J: Screws 5/16″ x 1-1/2″ (4x)

• K: Washers (4x)

• L: Screw Caps (4x)

• M: Allen Wrench (1x)

Follow these steps to assemble the AMAZON BASICS B07V6Z97QJ chair:

1. Insert the five casters (A) into the legs of the base (B). Insert the gas lift (C) into the center hole of the base.

2. Attach the seat mechanism (D) to the underside of the seat cushion (G) using four screws (H) and the Allen wrench (M).

3. Attach the backrest (F) to the back of the seat mechanism using four screws (I) and the Allen wrench (M).

4. Place the assembled upper part of the chair onto the gas lift (C) on the base assembly.

5. Attach the armrests (E) to the sides of the seat and backrest assembly using four screws (J) and four washers (K) with the Allen wrench (M). Ensure the washers are placed between the screw head and the armrest bracket.

6. Press the screw caps (L) into the screw holes on the armrests to cover the screw heads.

To adjust the seat height of the AMAZON BASICS B07V6Z97QJ chair, pull the lever located under the right side of the seat upwards. The seat will rise. To lower the seat, pull the lever up while seated.

The tilt lock feature on the AMAZON BASICS B07V6Z97QJ chair is controlled by the same lever used for height adjustment.

• To lock the chair in an upright position, push the lever inwards towards the center of the chair.

• To unlock the tilt function and allow the chair to recline, pull the lever outwards away from the chair.

To adjust the tilt tension of your AMAZON BASICS B07V6Z97QJ chair, use the large round knob located under the front of the seat.

• Turn the knob clockwise (towards the “+” symbol) to increase the tension, making it harder to tilt back.

• Turn the knob counter-clockwise (towards the “-” symbol) to decrease the tension, making it easier to tilt back.

To clean the AMAZON BASICS B07V6Z97QJ chair, wipe with a soft, slightly moist cloth.

Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

• Check the components regularly to make sure all screws and bolts are tightened.

• Store in a cool and dry place away from children and pets, ideally in original packaging.

• Vacuum the upholstery regularly. Small dust particles are very abrasive and can wear furniture prematurely.

• Avoid placing the product furniture in direct sunlight as color may fade over time when placed in direct sunlight.

• Try to maintain at least 3 feet (1 meter) between the product and any heat sources. Prolonged exposure to heat sources or radiators causes cracking in the leather.