AMAZON BASICS B00GUTY3DK (01) PDF MANUAL

The contents include:

• Mini Portable Bluetooth Speaker

• Carrying pouch

• USB charging cable

• This BTV2 Instruction Manual

Your speaker is partially charged when it arrives so you can use it right away. For the best reception, keep your speaker within 30 feet of the device it’s paired to.

1. Turn ON your speaker. A tone sounds, the LED blinks quickly, and your speaker enters pairing mode.

Note: If you do not hear a tone and the LED doesn’t blink quickly, press and hold the function button for 1 to 3 seconds to put your speaker in pairing mode. A tone sounds and the LED blinks quickly.

2. Turn ON your Bluetooth device (like a phone or tablet).

3. On your device, locate your Bluetooth settings and turn on Bluetooth.

4. In Bluetooth Settings, scan for devices if necessary, then select Amazon_BT2 from your device’s list. The LED stops blinking and lights blue. Your device and speaker are paired and your speaker is ready to use.

If the speaker does not automatically enter pairing mode (tone sounds, LED blinks quickly) when turned on, press and hold the function button for 1 to 3 seconds to put it in pairing mode. A tone will sound and the LED will blink quickly.

The speaker stays in pairing mode for 3 minutes or until you pair a device. If you do not pair a device within 3 minutes, the speaker exits pairing mode and the LED flashes slowly. To start pairing mode again, press and hold the function button for 2 seconds.

1. Disconnect from the previous device by pressing and holding the function button for 1 to 3 seconds. A tone sounds, the LED blinks quickly, and your speaker enters pairing mode.

2. Repeat the pairing steps for your next device.

You can pair multiple devices with the speaker, but you can only have one device actively paired at a time.

When the speaker is successfully paired with your device, the LED stops blinking and lights blue. Your device and speaker are paired and your speaker is ready to use.

Start playing music on your paired device. Music will play through your speaker.

On your speaker, press + or – to increase or decrease the volume. A tone sounds when the maximum volume setting is reached.

Press the function button to pause playback. Press again to resume playback.

You can listen through your speaker and speak through your speaker’s microphone during phone calls.

Position your speaker about 2 feet away and speak normally. For the microphone to pick up your voice effectively, make sure that the microphone is facing you. The LED should be closest to you.

If you make a call while paired, the audio and microphone automatically default to your speaker.

• Use your phone to make the call.

• Press the function button on the speaker to end the call.

If you receive a call while paired, your phone rings through your speaker.

To listen and speak through your speaker:

• Press the function button to answer the call.

• Press the function button to end the call.

• Press and hold the function button to reject the call.

To listen and speak through your phone (depending on your phone) instead of the speaker during a call:

• Use your phone to answer the call initially.

OR

• Use your phone’s settings to switch to your phone audio during a call.

1. Connect a 3.5 mm audio cable (not included) from your speaker’s AUX jack to your audio device (like an MP3 player).

2. If connected to Bluetooth, press and hold the function button to disconnect from Bluetooth. This allows the AUX connection to take precedence.

When connected to AUX, use the controls on the connected audio device (e.g., MP3 player, phone) instead of your speaker’s buttons for playback and volume control.

When your speaker is turned on and the battery is low, your speaker’s LED flashes red. If not charged, your speaker turns off.

To charge your speaker, connect the USB charging cable to the charging port on your speaker and an available USB port on your computer.

• If your speaker is ON, the LED lights purple when charging. When fully charged and connected to a Bluetooth device, the LED lights blue.

• If your speaker is OFF, the LED lights red while charging and turns off when fully charged.

• Move your speaker and Bluetooth device closer together.

• If you do not pair a device within 3 minutes, your speaker exits pairing mode and the LED flashes slowly. Press and hold the function button for 1 to 3 seconds to put your speaker into pairing mode. A tone sounds and the LED blinks quickly.

• Press and hold the function button to make sure that your speaker is not connected to any other Bluetooth device (this action typically puts the speaker into pairing mode, disconnecting previous active connections).

• Adjust the volume on your device. It should be at about 50% as a starting point.

• Adjust your speaker volume using the + or – buttons on the speaker.

• Make sure that your phone is paired to your speaker.

• Make sure that the microphone is facing you. The LED should be closest to you, as the microphone is located on the front panel near the LED.

• Move your speaker closer to your paired device. The maximum distance is 30 feet.

• Turn down the volume on both the speaker and the connected device, then gradually increase it to a comfortable level.

• Some functions may be restricted depending on the device paired to your speaker.

• If the device is connected to the AUX jack, you must use the controls on the connected device, not the speaker buttons.

• Make sure the device is within 30 feet of your speaker.

• Make sure your device supports Bluetooth 4.0 (the speaker supports Bluetooth 4.0).

To reduce the risk of fire or electric shock: Do not expose this appliance to rain or moisture.

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.