ADVANTECH AWS-8129H1-RAE (01) PDF Document

The ADVANTECH AWS-8129H1-RAE is an industrial workstation featuring a 12.1 inch flat panel display, designed to meet tough industrial standards with a high-quality steel frame for security and environmental protection.

Before setting up your ADVANTECH AWS-8129H1-RAE, ensure the following materials are present:

1. One ADVANTECH AWS-8129H1-RAE industrial workstation with 12.1 inch flat panel display.

2. One accessory box, including: one HMI products drivers and utilities CD-ROM, one utility diskette for function key programming, one user’s manual, a cable to link the front PS/2 connector to the CPU card, a flat gray cable for 3.5 inch HDD and slim CD-ROM, a Y-cable for PS/2 keyboard and mouse, an RS-232 cable to link the touchscreen to the CPU card (only on -T models), and a screw bag with screws.

To ensure safe operation of the ADVANTECH AWS-8129H1-RAE, follow these instructions:

1. Read safety instructions carefully and keep the manual for reference.

2. Disconnect from AC outlet before cleaning with a damp cloth; do not use liquid or spray detergents.

3. Ensure the power outlet is near the equipment and easily accessible.

4. Keep the ADVANTECH AWS-8129H1-RAE away from humidity.

5. Place on a reliable surface to prevent falling damage.

6. Do not cover air convection openings.

7. Ensure source voltage is correct before connecting.

8. Position power cords to prevent tripping and do not place items over them.

9. Disconnect if not used for long periods to avoid transient overvoltage damage.

10. Do not pour liquid into any openings.

11. Do not open the unit; servicing should only be performed by qualified personnel.

12. Do not leave the ADVANTECH AWS-8129H1-RAE in uncontrolled environments where the storage temperature is below -20 degrees Celsius or above 60 degrees Celsius.

To use the keyboard and keypad on the ADVANTECH AWS-8129H1-RAE simultaneously, you must connect the keyboard connector on the backplane to the keyboard connector on the CPU card. Then, connect the external keyboard jack to the keyboard jack located next to the power supply. Note that if you connect the keyboard to the 5-pin DIN connector on the CPU card, neither the keyboard nor the keypad will work.

The ADVANTECH AWS-8129H1-RAE has the following general specifications:

Front panel: Aluminum, meets NEMA 4 or IP 65.

Disk drive housing: Supports one slim 3.5 inch FDD, one 3.5 inch HDD and one slim CD-ROM.

Cooling system: One 49 CFM fan on rear panel.

Keyboard connector: 6-pin PS/2 connector with dust-proof door on front panel.

Operating temperature: 0 to 50 degrees Celsius (32 to 122 degrees Fahrenheit).

Relative humidity: 5 to 85 percent at 50 degrees Celsius, non-condensing.

Dimensions (W x H x D): 482 x 266 x 307 mm (19.0 x 10.5 x 12.1 inches).

Weight: 15 kg (33 lb).

The ADVANTECH AWS-8129H1-RAE features the following LCD display technical details:

To install cards in the ADVANTECH AWS-8129H1-RAE, first open the top panel. Slowly slide the card into the backplane socket and press carefully to seat it. Secure the card with a screw to the top mounting bar. Connect any necessary wires, and then reattach the cover once finished.

The ADVANTECH AWS-8129H1-RAE allows for the installation of additional drives. To add a 3.5 inch hard disk drive or a slim CD-ROM drive, unscrew the drive mount assembly from the body of the case. Attach the drive to the assembly using the provided screws, and attach the ribbon connector. Once the drive is secured, set the ribbon cables in place and mount the drive mount assembly back into the case.

To mount the ADVANTECH AWS-8129H1-RAE within a panel, set the unit within your panel aperture so that the screw holes on the panel align with the mounting bolts on the flange of the ADVANTECH AWS-8129H1-RAE. Secure the bolts to the panel.

To program the macro keys on the ADVANTECH AWS-8129H1-RAE, copy the files from the utility disk to your hard disk. Locate the .pad file that corresponds to the ADVANTECH AWS-8129H1-RAE. Boot your workstation, enter the DOS command, and run the Main.exe program. Use the “Load” function to load the definition file, and the “Edit” function to select and define the macro keys. When finished, use the “Save” function to save your changes with a .txt extension. Finally, use the “Run” function to program the keyboard translator board with the new settings.

Before servicing the power supply of the ADVANTECH AWS-8129H1-RAE, you must shut off all power and unplug the unit. Detach and remove the top and rear covers. Unscrew the four screws on the side panel, and disconnect all DC output connectors and the AC line to remove the power supply.

To replace the LCD backlight in the ADVANTECH AWS-8129H1-RAE, follow these steps:

1. Open the top and rear covers.

2. Disconnect the cable from the LCD controller and LCD.

3. Pull out the bracket located below the backplane.

4. Detach the bracket behind the front panel.

5. Disconnect the inverter cables and any touchscreen controller cables.

6. Unscrew the four screws holding the LCD and carefully pull it out.

7. Unscrew the screws on the LCD unit and change the backlight. Use caution, as the backlight is small and fragile.

To service or replace the keyboard translator on the ADVANTECH AWS-8129H1-RAE, switch off the power and detach the main power cord. Detach the work drawer and cover from the unit. Pull the work drawer out, remove the keypad connector protective bracket, and carefully detach all cables connected to the keyboard translator. Finally, unscrew the four screws on the corners to pull out and replace the board.

To service or replace the touchscreen controller on the ADVANTECH AWS-8129H1-RAE, open the top and rear covers, disconnect the cable from the LCD controller and LCD, and pull out the bracket located below the backplane. Detach the bracket behind the front panel, disconnect the inverter and touchscreen controller cables, and replace the controller. Do not bend the touchscreen tail attached to the touchscreen sensor.

The power supply specifications for the ADVANTECH AWS-8129H1-RAE include:

Input range: 90 to 135/180 to 265 VAC.

Input frequency: 47 to 63 Hz.

Maximum continuous DC output power shall not exceed 250 W.

The output load range is detailed below: