ADLER AD 7064 (01) PDF Document

Attach one end of the aluminum tube into the motor housing by aligning the two connectors in place and push until an audible click can be heard, indicating that the release button has locked in place properly.

Attach the floor brush or the electric mopping brush into the other end of the aluminum tube by releasing the button on the aluminum tube, using the same method as assembling the aluminum tube to the motor housing.

Attach the crevice nozzle or 2-in-1 brush for upholstery into the motor housing and push inside until an audible click can be heard, indicating that the release button has locked in place properly.

Plug the charging adapter into an electrical outlet and into the charging port located on the motor housing. During charging, the battery indicator icon on the touch LED screen will flash. After being fully charged, the battery indicator icon will remain lit continuously.

Press the release button on the wall mount to install the motor housing onto the wall mount. Then, plug the charging adapter into a power outlet and the charging port located on the side of the wall mount. During charging, the battery indicator icon on the touch LED screen will flash. Once the charging of the battery module is complete, press the release button again to remove the motor housing.

The icons provide the following information:

Brushes icon: Lighted continuously during normal brush operation; flashes when the floor brush or mopping brush is blocked.

Airflow icon: Lighted continuously during normal device operation; flashes when the airflow is blocked. If it flashes, switch off the device and remove dust from the dust container.

Charging icon: Lighted continuously during the normal charging process. If it flashes, there is an issue with the charging process.

Battery icon: Lighted continuously during normal operation. It consists of 4 elements. When fully charged, 4 elements are visible. When the battery is low, only one element is stable. When completely discharged, the screen turns off. During charging, the icon shows an increasing number of elements.

White fan icon: The strip under the icon indicates low, middle, or high suction power.

AUTO icon: Flashes when activated. Current suction power is based on the dust/dirt level detected by the dust sensor. Activation is shown by the color of the light ring around the LED screen: blue for low suction, red for middle suction, and purple for high suction.

First, assemble the desired brush. Press and hold the power button for about 3 seconds to turn on the device. The default mode is high-level suction power. Use the white fan icon on the touch LED screen to adjust suction power between low, middle, and high. To use automatic mode, touch the AUTO icon. The AUTO icon will flash when active, and the vacuum will adjust its suction power based on the dirt detected. Press the power button again to switch off the device.

Open the water tank lid on the electric mopping brush and pour in water. Do not use foaming cleaning agents or bleach. Close the lid. Assemble the mopping brush to the tube and motor housing. Unlock the water feed by turning the water feed knob to the position of the open padlock icon on the water tank surface. Press and hold the power button for about 3 seconds to turn on the vacuum. The pads will rotate to start wet cleaning. To stop the water flow, turn the water feed knob back to the closed padlock icon position.

Switch off the device and disassemble the tube. Hold the motor housing over a trash can or toilet, and press the dust container release button. The container will open at the bottom, and the dust will fall out.

Filters should be cleaned regularly. Disassemble the filters from the dust container before cleaning. Do not pour water inside the dust container to clean the filter, as this will damage the device. The stainless steel mesh filter and the HEPA filter must be twisted anticlockwise to unlock them. The stainless steel mesh filter can be cleaned with a dry brush. The HEPA filter should be shaken to remove dust, cleaned with a dry brush, and can finally be washed with tap water. Ensure the HEPA filter is completely dry before reassembling.

Troubleshooting steps include:

If the device does not work: Check the battery status on the touch LED screen. If the battery is low, charge the battery module.

If the device cannot vacuum or has weak suction: Empty the dust container if it is full. Also, check if the battery power is sufficient and charge it if necessary.

If there is a dirt leak: Ensure the dust container is not full. Make sure the release button at the bottom of the dust container is locked.

If the motor unit cannot suck when connected to the floor brush: Empty the dust container, clean the container and filters, and ensure the openings and aluminum tube are not blocked by debris.

Wipe the mopping brush with a damp cloth and dry it thoroughly before use. The pads can be cleaned in a washing machine at 40 degrees Celsius using a standard cleaning agent. To replace pads, pull them off the mopping brush surface, as they are attached with Velcro. Ensure the new pads are placed in the same position.