ZOJIRUSHI SF-SD10 (01) PDF Document

Keep the bottle out of reach of infants and small children to prevent risks of scalding or injury.

Always clean the bottle thoroughly after use to prevent malfunctions like rusting, perforation, or spoiled contents.

Always close the stopper tightly to prevent beverages from spilling and ensure the spout is closed after pouring.

Do not use the bottle if it loses its heat retention properties, as the outside may become very hot if hot beverages are poured inside.

Consume beverages within the same day to prevent them from spoiling and producing gas that could increase internal pressure.

Do not place cans or bottles inside the main body, as they may deform or damage the product.

Do not remove the sticker on the bottom of the main body, as this may cause malfunctions such as rusting or perforation.

Do not drink out of the bottle while driving to avoid scalds, stains, or serious accidents caused by distraction.

Leave 1cm (1/2 inch) of room on top when filling the bottle. Filling beyond the ridge may cause contents to overflow when placing the stopper, or beverages may become caught in the stopper and leak out.

Tilt the product slowly when pouring hot beverages to avoid scalds.

Do not shake the bottle, as it may cause scalds or injuries.

Be careful not to scald yourself when drinking. Because of vacuum insulation, the outside of the bottle will not feel hot even if the contents remain very hot for many hours.

Always use the cup when drinking hot beverages. Never drink directly out of the bottle.

If the stopper becomes difficult to remove when filled with hot beverages, press the button to open the spout to release internal pressure before removing the stopper. Do not forcefully remove the stopper.

Dry ice and carbonated drinks: These can cause the spout to become difficult to open or cause the stopper and cup to burst.

Liquids containing salt, such as soup: These can cause rust resulting in the loss of thermal insulation.

Dairy products and fruit juice: If left inside for a long period, contents may spoil and produce gas that could cause the stopper to burst.

Fruit pulp and tea leaves: These may become caught in the stopper and cause contents to spill.

Do not leave a tea bag inside and close the stopper, as the bag may swell and cause leaks.

Rinse the inside and outside of the main body mouth, the stopper, and the cup as soon as possible after consumption to prevent rust or pinholes.

Clean the inside using a soft sponge to protect the nonstick coating from being scratched. Scratches to the coating may cause rust and pinholes.

Outside Main Body: This model cannot be washed under water. Washing under water may allow water to get inside and cause rusting or leaking. To clean, soak a soft cloth in warm water and mild dishwashing liquid, wring it well, and wipe the surface.

Cup and Stopper: Wash with warm water and mild dishwashing liquid using a soft sponge with a handle. Rinse and wipe moisture out to dry. Detach and wash gaskets after each use and remember to reattach them.

Inside Main Body: Fill with warm water, close the stopper, and pour the water out through the spout several times. Remove the stopper, wash with warm water and mild dishwashing liquid using a soft sponge with a handle, then rinse and wipe dry.

Carrying Strap: Soak a soft cloth in warm water and dishwashing soap, wring well, and wipe clean.

Do not soak the main body.

Do not clean using paint thinner, benzine, metal wire scrub brushes, scrubbing brushes that include abrasive cleansers, polishing powders, cleansers, or melamine sponges.

Do not use chlorine type bleach, as it may cause rusting on the inner surface and spring used in the stopper.

Do not use a dishwasher or dish-dryer.

Do not boil to sanitize, as it may cause damage, rusting, or deformation.

To remove rust spots or water stains: Fill the bottle with hot water with 10 percent vinegar and let it stand for 30 minutes to one hour without attaching the stopper, then wash the interior thoroughly.

To remove coffee and tea stains: Use Zojirushi cleaning detergent SB-ZA01 or SB-ZA01E. Always remove the stopper when using these cleaners.

Stand the bottle upright and wait 2 to 3 seconds before closing the spout. This prevents droplets from remaining inside the cup or leaking later. Wipe off any excess liquids on the cup before closing.

This occurs when the bottle is filled with hot beverages. Heat causes air inside to expand, building up internal pressure. To prevent this, when filling with hot beverages, close the stopper while keeping the spout open, wait about 20 seconds, and then close the spout.

Yes, a rattling noise heard when the product is shaken comes from the copper or aluminum foil in the vacuum insulation. This is used to increase heat or cold retention and does not indicate a malfunction.