Free English YAMAHA KPA-501 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD YAMAHA KPA-501 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I operate the YAMAHA KPA-501 for basic karaoke play?
Follow these steps to begin using your YAMAHA KPA-501:
1. Turn on the power of the unit.
2. Select the source to be played with the INPUT selector and start playback. Adjust the volume control to the appropriate level.
3. Select the speakers system by pressing the SPEAKERS A and/or B button.
4. Connect the microphone(s) to the MIC jack(s) and turn on the microphone(s).
5. Adjust the microphone level with the LEVEL control while speaking into the microphone.
6. Re-adjust the overall volume with the VOLUME control.
How do I play sound multiplex sources on the YAMAHA KPA-501?
When playing a sound multiplex karaoke disc or tape, perform the following on your YAMAHA KPA-501:
1. Press the MPX/STEREO button so that the MPX indicator lights.
2. Adjust the MPX BALANCE control. To decrease the volume level of the original vocals, turn the control toward MUSIC.
How do I play general stereo sources on the YAMAHA KPA-501?
When playing a stereo source such as general CDs, LDs, or music tapes, ensure that the MPX/STEREO button is set to STEREO so that the MPX indicator goes off. Then, press the ONE TOUCH KARAOKE button so that the indicator lights. This reduces the volume of the original vocals.
How do I add echo effects to my voice on the YAMAHA KPA-501?
The YAMAHA KPA-501 uses the ECHO and DELAY controls for this purpose:
To adjust the echo level, turn the ECHO control toward 10 to increase the level or toward 0 to decrease it.
To adjust the echo length, turn the DELAY control toward 10 to expand the length or toward 0 to shorten it.
Note: If a high-pitched howling sound occurs, separate the microphone farther away from the speakers, decrease the microphone level, or lower the overall volume with the VOLUME control.
How do I adjust the music tone and balance on the YAMAHA KPA-501?
Use the following controls on your YAMAHA KPA-501:
To adjust the balance between left and right speakers, use the BALANCE control. Turn toward R to move the sound image to the right, or toward L to move it to the left.
To adjust only the music volume, turn the MUSIC VOLUME control. Turn toward -20 dB to decrease the volume of input sources other than the microphones.
To adjust the high frequency sound, use the TREBLE control. Turning toward +5 increases high frequency sound levels, while turning toward -5 decreases them.
To adjust the low frequency sound, use the BASS control. Turning toward +5 increases low frequency sound levels, while turning toward -5 decreases them.
How do I replace original vocals with my voice on the YAMAHA KPA-501?
Press the VOCAL AID button on your YAMAHA KPA-501 so that the indicator lights. When you sing into the microphone, your voice will replace the original vocals.
How do I use vocal effects on the YAMAHA KPA-501?
You can select the following effects on the YAMAHA KPA-501 to suit the music type you sing:
BALLAD: Suitable for mellow songs with slow-tempo.
POPS: Suitable for pop music.
JAZZ: Provides reflections like in a small hall for a jazz club atmosphere.
ROCK: Suitable for dynamic and rhythmical rock sound.
Press the same button again to cancel the effect.
How do I obtain the desired musical pitch on the YAMAHA KPA-501?
Use the DIGITAL KEY CONTROLLER buttons on the YAMAHA KPA-501 to obtain the desired musical pitch. You can lower the pitch, return to normal pitch, or heighten the pitch. If the input signal is interrupted for about 4 seconds, the setting will return to the normal pitch.
How do I record karaoke play on the YAMAHA KPA-501?
You can record using a cassette deck or VCR connected to the YAMAHA KPA-501. Before recording, select the source to be played with the input selectors. When recording, select a source other than TAPE or VCR as applicable.
How do I troubleshoot common issues on the YAMAHA KPA-501?
| Symptom | Possible Cause | Remedy |
|---|---|---|
| Your voice is not heard through the microphone. | Microphone plug is not firmly inserted or microphone is turned off. | Insert plug firmly or turn on the microphone. |
| Volume of original vocals cannot be reduced when MPX BALANCE is turned to MUSIC. | MPX/STEREO button not set properly. | For sound multiplex, set to MPX. For general stereo, set to STEREO and press ONE TOUCH KARAOKE. |
| Your voice does not replace original vocals when VOCAL AID is pressed. | Microphone volume is low or singing voice is not loud enough. | Turn up microphone volume with MIC LEVEL control or sing louder. |
| The sound of the playback source is not heard. | Input selector not set properly or jumper bars not firmly inserted. | Set to the correct source or insert jumper bars firmly into ACCESSORY jacks. |
How do I connect speakers to the YAMAHA KPA-501?
To connect speakers to the YAMAHA KPA-501, follow these steps:
1. Raise or press down the terminal tab.
2. Insert the bare wire (after removing approx 5mm/1/4 inch of insulation from the speaker wires).
3. Press down or raise the tab to secure the wire.
Ensure that the polarity (+ and -) of the speaker wires is correct. Do not let the bare speaker wires touch each other or the metal parts of the unit.
CLICK HERE TO DOWNLOAD YAMAHA KPA-501 (01) PDF DOCUMENT