VOX SS-T008B (01) PDF DOCUMENT

WARNING: Separate the handheld part from the power cord before cleaning the handheld part in water.

1. This product uses a USB charging cable.

2. You can use a 5V adapter mobile phone charger, or a USB interface of cars, computers and others for charging.

3. If the charging cable is damaged, replace it with a new one to avoid danger.

4. The product shall be charged and stored between 5°C and 35°C.

5. Make sure the charge and charging cable are dry. Do not plug or unplug with wet hands to prevent electric shock.

6. Please check if the foil is damaged or deformed before use to avoid damage to your skin.

7. Clean the electric shaver with clean water, but do not soak it in water for a long time.

8. Do not use salt water, hot water above 60°C, thinners, gasoline, alcohol or other chemicals to clean the electric shaver.

9. During the use and charging process, the electric shaver may be slightly heated. This is normal and please feel free to use it.

10. Please do not charge the electric shaver too long.

11. Do not store the electric shaver in direct sunlight or near other sources of heat.

1. When the display shows “Available time, 05 minutes”, the indicator light will flash, indicating that the battery is low-energy and needs charging.

2. Plug the USB charging cable end into the electric shaver, then connect the USB cable to the charger and plug it into the power socket, or plug the other end of the USB cable into a USB port of computers or cars.

3. When the power is turned on, the display will light up, with scrolling numbers which will increase as the charging time extends, indicating that it’s charging.

4. Full charging takes about 1.5 hours on a continuous basis. After full charging, “FULL” and “90 min” will be displayed, indicating the shaver has been fully charged and can be used for about 60 minutes (Note: 90 means a rough available duration instead of full charging until 100).

The LED display of this product can display remaining energy. A fully charged electric shaver can provide a shaving duration up to about 60 minutes, but the actual shaving duration may be less than expected due to differences in shaving habits, cleaning habits and beard types.

Note: The electric shaver can be used while it’s being charged by means of USB cable connection if it still has remaining energy.

1. Press the switch button to turn on the electric shaver.

2. Move the electric shaver foil against the growth direction of your beard on your skin and make straight and reciprocated movements.

3. Hair on your neck can also be shaved.

4. Before shaving your head, clean it with warm water and keep your hair dry. For a better effect of use, please use the brush if you need to clean the shaving head during the head shaving process, and wash the shaving head after shaving is completed.

When shaving is completed:

Press the switch button again to turn off the electric shaver.

Please do not use any damaged shaving head to avoid injury to your skin; instead, replace it immediately with our original spare shaving head which can be bought where you buy your shaver.

1. Press and hold the electric shaver switch button for 3 seconds, and then the electric shaver LED display indicates that the safety lock has been locked.

2. Repeat the above step to unlock.

1. Stall protection: When the electric shaver is overloaded, it will be automatically turned off, and the LED display will indicate stall protection. At this time, it should be cleaned up before use.

2. Cleaning reminder: When the faucet symbol flashes on the LED display, it indicates that the electric shaver needs to be cleaned.

To ensure a better shaving effect, the shaver must be cleaned regularly. The easiest and most sanitary way to clean the product is to wash the shaver head part and the whisker storeroom with water each time after using it.

Do be careful while using hot water. Do remember to check the water is not too hot to avoid harming hands.

1. Cut off the power supply of the shaver, then unplug the charger and also pull out the product’s plug from the shaver.

2. Open the shaver head part.

3. Clean the shaver head part and the hair storeroom with hot running water.

Make sure both of the shaver head part and the hair storeroom be cleaned thoroughly.

4. Wash the product’s surface.

5. Close the shaver head part and throw off surplus water.

Do not wipe the shaver head part with a towel or paper tissues, which may cause damages to the shaver head.

The shaving head should be replaced at least once every six months for a good experience. If there is no damage caused by human factors, the shaver can have a long service life. Any damaged shaving head can only be replaced with our original double-ring blade shaving head.

Separate the handheld part from the power cord before cleaning the handheld part in water.

Operating Instructions

Switch off the shaver, pull it up (not screw) to unload the shaving head, and insert the flange of the hair clipper head part into the groove on the top of the shaver body. Then press down the hair clipper head part to mount it on the shaver body (a click will be heard).

Trim

Note: Make sure your hair is clean and dry, and please don’t use the product for wet hair just washed.

1. Before trimming, first do remember to comb hair along its growth direction with a comb.

2. Mount the comb accessory into the slots on both sides of the product (a click will be heard), and make sure it’s mounted correctly.

3. The included combs are optional for different haircut lengths, such as 3mm, 5mm and 7mm, which can be mounted as required. To replace a comb, unload it from the groove on one side first.

4. Press the ON/OFF button and move the product slowly on hair. To get the best haircut effect, it’s necessary to move the product against the growth direction of hair.

Clean

1. Pull out the hair clipper head and clean the trimming part with the included brush or wash the hair clipper head assembly with water.

2. Don’t clean the product with such liquids as abrasives, alcohol, petrol or acetone.

3. Clean the product immediately each time it’s used.

Mounting Instructions for Vibrissa Trimmer

Switch off the shaver, pull it up (not screw) to unload the shaving head, and insert the flange of the vibrissa trimmer head part into the groove on the top of the shaver body. Then press down the vibrissa trimmer head part to mount it on the shaver body (a click will be heard).

Nose and ear trimmer head (Nose Hair)

1. Make sure your nasal cavity is clean.

2. Start the ON/OFF button, insert the vibrissa trimmer tip into one of your nasal cavities slowly and meanwhile turn the tip to remove overlong vibrissa. The insertion depth of the tip into your nasal cavity must not exceed 0.5cm. To reduce pruritus, make sure that one side of the tip is firmly pressed against your skin.

Trim Ear Hair

1. Clean your external auditory canal to ensure there is no cerumen.

2. Start the ON/OFF button and then make the tip circle along your ear gently to remove protrudent hair on your helix.

3. Insert the vibrissa trimmer tip into the external auditory canal carefully. The insertion depth of the tip into your auditory canal shall not exceed 0.5m, or else your eardrum may be injured.

Remove sebum and dirt on your face with the facial cleaner every day, which helps to keep your skin clean and healthy.

1. Make sure the device has been turned off and that the cleaning brush has been attached to the device.

2. Moisten the facial cleaner with water. Do not clean your face directly with a dry facial cleaner, which may irritate your skin.

Environmental Protection

1. To discard the product, please don’t put it together with general domestic rubbish heaps but hand it to the officially designated recycle center for the environmental protection.

2. The built-in rechargeable battery contains substances which may pollute the environment, so it must be unloaded from the product or sent to the officially designated recycle center to be disposed before it is discarded. The battery should not be unloaded unless it has been used up.

1. Unplug the charger and also pull out the product’s plug from the shaver.

2. Unload the battery. Do not plug in the shaver again after unloading the battery.