VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 (01) PDF Document

The specifications for the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 are as follows:

Max. load: 10 kg / 22 lbs

Max. load Curved Display: 10 kg / 22 lbs

To mount the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 using the desk clamp, follow these steps for a desk with a maximum thickness of 66 mm:

Step 1. Place the pole base (B) on the edge of your desk.

Step 2. From underneath the desk, position the clamp plate (A).

Step 3. Securely tighten the clamp plate (A) against the underside of the desk.

Step 4. Insert the pole into the base (B).

To mount the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 through a desk grommet or a drilled hole, follow these steps. This method is for desks with a thickness between 35 mm and 45 mm.

Step 1. If a hole is not present, drill a 9 mm diameter hole in your desired mounting location.

Step 2. Place the pole base (B) on the desk, aligning it with the hole.

Step 3. From underneath the desk, insert the bolt (J) through the bottom plate (M) and washer (L).

Step 4. Screw the bolt (J) into the bottom of the pole base (B) and tighten it securely.

Step 5. Insert the pole into the base.

After mounting the base and pole, assemble the arm for your VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 as follows:

Step 1. Slide the arm collar (P C201) onto the pole. Adjust it to your desired height and tighten it in place.

Step 2. Place the lower arm section (1x C320) onto the collar (P C201).

Step 3. Attach the upper arm section (D C327) to the top of the lower arm section.

Step 4. Attach the VESA head (E C501) to the end of the upper arm section (D C327).

To attach your monitor to the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 arm, follow these steps:

Step 1. Align the VESA plate (E) with the mounting holes on the back of your monitor. Make sure the side marked “TOP” is facing up.

Step 2. Secure the VESA plate to the monitor using the four provided screws (N).

Step 3. Carefully lift your monitor and lower the attached VESA plate (E) onto the head of the monitor arm.

Step 4. Push down gently until you hear a “CLICK,” indicating the monitor is securely locked in place.

To set the overall height of your monitor on the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137, follow these instructions:

Step 1. Remove the monitor and arm assembly from the main pole.

Step 2. Loosen the screw on the arm collar (P C201) and slide it up or down the pole to your desired height.

Step 3. Once positioned, retighten the screw on the collar to lock it in place.

Step 4. Place the arm and monitor assembly back onto the secured collar.

If your monitor tilts too freely or is too stiff, you can adjust the tilt friction on the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137.

Step 1. Locate the tilt friction adjustment screw on the VESA head.

Step 2. To increase friction (make it harder to tilt), turn the screw towards the “+” symbol.

Step 3. To decrease friction (make it easier to tilt), turn the screw away from the “+” symbol.

Step 4. Adjust until the monitor holds its angle but can still be moved with reasonable force.

To ensure the arm of your VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137 can hold your monitor’s weight at any height, you must adjust the balance:

Step 1. Position the upper arm so it is horizontal (at a 90-degree angle to the lower arm).

Step 2. Locate the adjustment screw (F) on the main arm joint.

Step 3. Use the H5 Allen key to turn the screw.

Step 4. If you have a heavy monitor and the arm sags, turn the screw towards the “+” symbol to increase the tension.

Step 5. If you have a light monitor and the arm rises on its own, turn the screw away from the “+” symbol to decrease the tension.

Step 6. Continue adjusting until the arm stays in place when you let go.

To route and conceal monitor cables on your VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4137, use the integrated cable management system:

Step 1. Open the cable cover on the underside of the lower arm section (1x C320).

Step 2. Place your cables inside the channel and snap the cover back into place.

Step 3. Open the cable cover on the upper arm section.

Step 4. Route the cables through this upper channel and close the cover.

Step 5. Guide the cables from the arm down the main pole to complete the setup.