VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127 (01) PDF Document

The maximum load capacity for the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127 is 10 kg / 22 lbs. This applies to both standard and curved displays.

To mount the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127 using the desk clamp, follow these steps for desks up to 66 mm thick:

Step 1. Attach the lower clamp plate (A) to the pole base (B).

Step 2. Use the provided Allen key (H5, located in the VESA head C501) to secure the clamp plate with the four screws (H).

Step 3. Place the assembled pole base onto the edge of your desk.

Step 4. From underneath the desk, tighten the clamp screw by hand until the base is firmly secured to the desk.

To mount the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127 through a desk grommet or drilled hole, your desk must be between 35 mm and 45 mm thick.

Step 1. If a suitable hole does not exist, drill a 9 mm diameter hole in the desired location on your desk.

Step 2. Place the pole base (B) on the desk, aligning its center hole with the hole in the desk.

Step 3. From underneath the desk, place the bottom plate (J) over the hole.

Step 4. Insert the threaded bolt (M) with its washer (L) through the bottom plate (J) and the desk hole, and screw it into the bottom of the pole base (B).

Step 5. Tighten the bolt until the pole base is secure.

To assemble the monitor arm for the VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127:

Step 1. Slide the lower arm connector (P) over the main pole (B) to the desired height and tighten it.

Step 2. Place the upper arm section (D) onto the lower arm connector (P).

Step 3. Attach the VESA head assembly (E) to the end of the upper arm (D).

Follow these steps to attach your monitor:

Step 1. Attach the VESA plate (E) to the back of your monitor using the four provided screws (N). Ensure the side marked “TOP” is oriented upwards.

Step 2. Lift your monitor and align the opening on the attached VESA plate with the mounting head at the end of the monitor arm.

Step 3. Lower the monitor onto the arm head until you hear a “CLICK”, which indicates it is securely locked in place.

If the monitor tilts too easily or is too stiff, you can adjust the tilt friction. Use an Allen key to tighten or loosen the adjustment screw located on the side of the VESA mounting head. Tightening the screw increases friction, making the tilt stiffer, while loosening it makes the monitor easier to tilt.

After mounting your monitor, you may need to adjust the gas spring tension to balance the monitor’s weight, allowing for smooth height adjustment.

Step 1. Locate the adjustment screw (F) on the upper arm.

Step 2. If your monitor is heavy and drifts downward, use the Allen key (H5) to turn the screw toward the “+” symbol to increase the tension.

Step 3. If your monitor is light and drifts upward, turn the screw toward the “-” symbol to decrease the tension.

Step 4. Continue to adjust until the monitor stays in position when you let go.

The VOGEL’S MOMO MOTION+ (MOTIONPLUS) 4127 features integrated cable management to keep your workspace tidy.

Step 1. Open the cable management cover on the underside of the lower arm.

Step 2. Route your monitor’s power and display cables along the inside of the upper and lower arm sections, securing them within the provided channels and clips.

Step 3. Close the cable management cover to conceal the cables.

Step 4. Route the cables down the pole and secure them as needed.

To set the overall height range of the monitor arm on the main pole, follow these steps:

Step 1. Remove the monitor and arm assembly from the pole.

Step 2. Loosen the height adjustment collar on the pole.

Step 3. Move the collar up or down to the desired height and tighten it securely.

Step 4. Place the arm assembly back onto the pole, resting on the repositioned collar.