VEVOR SR191522 (01) PDF MANUAL

Please read this manual carefully before using the product. Failure to do so may result in serious injury.

1. Assemble only according to these instructions. Improper assembly can create hazards.

2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.

3. Keep the assembly area clean and well-lit.

4. Keep bystanders out of the area during assembly.

5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.

6. The product capabilities apply to properly and completely assembled products only.

7. Assemble on a flat, level, hard and smooth surface capable of safely supporting the Rattan Accent Cabinet.

8. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

1. This product is not a toy. Do not allow children to play with or near this item.

2. Do not exceed weight capacities, before moving.

3. Use only on a flat, hard and smooth surface capable of safely supporting a fully loaded Rattan Accent Cabinet.

4. Use as intended only. Inspect before every use; do not use if parts are loose or damaged.

*Products such as specifications, appearance, and design are subject to modification without prior notice.

The package contains the following parts:

Part 1: Top Panel

Part 2: Left Side Panel

Part 3: Right Side Panel

Part 4: Legs (x4)

Part 5: Shelf

Part 6: Bottom Panel

Part 7: Left Door

Part 8: Right Door

Part 9: Upper Back Brace

Part 10: Back Panels (x2)

Part 11: Leg Support Braces (x2)

Part 12: Lower Back Brace

The following hardware is included:

A: Cam Lock x11

B: Cam Lock Dowel x11

C: Wood Dowel x10

D: Magnetic Catch Base x1

E: Handle x2

F: Screw x12

G: Shelf Support Pin x4

H: Hinge x4

I: Screw x4

J: Screw x10

K: Magnetic Catch Plate x2

L: Screw x18

M: Felt Pad x4

O: Washer x1

P: Screw x2

Q: Anti-Tip Strap x1

R: Screw x1

S: Wall Anchor x1

T: Anti-Tip Bracket x8

U: Screw x4

Follow these steps to assemble the cabinet:

Step 1: Fix hardware B (Cam Lock Dowel) to Part 2 (Left Side Panel) and Part 3 (Right Side Panel).

Step 2: Connect Part 3 (Right Side Panel) and Part 9 (Upper Back Brace) / Part 12 (Lower Back Brace) using hardware B (Cam Lock Dowel), and tighten them with hardware A (Cam Lock) and C (Wood Dowel).

Step 3: Connect Part 2 (Left Side Panel) and Part 9 (Upper Back Brace) using hardware B (Cam Lock Dowel), and tighten them with hardware A (Cam Lock).

Step 4: Insert Part 10 (Back Panels) into the groove of Part 2 and Part 3. Insert hardware C (Wood Dowel) into Part 2 and Part 3, and connect Part 6 (Bottom Panel) to Part 2 and 3 using hardware C. Fix Part 6 to Part 2 and 3 with screw I.

Step 5: Fix Part 11 (Leg Support Braces) to Part 6 (Bottom Panel) with screw F. Screw Part 4 (Legs) to Part 11. Stick hardware M (Felt Pad) to the bottom of the four legs.

Step 6: Slide Part 10 (Back Panels) into the groove of Part 2 and 3.

Step 7: Fix hardware B (Cam Lock Dowel) to Part 1 (Top Panel). Fix hardware D (Magnetic Catch Base) to Part 1 with screw J.

Step 8: Insert hardware C (Wood Dowel) into Part 2 and 3. Connect Part 1 (Top Panel) to Part 2 and 3 using hardware C. Tighten Part 1 to Part 2 and 3 with hardware A (Cam Lock).

Step 9: Fix hardware H (Hinge) to Part 7 (Left Door) and Part 8 (Right Door) with screw L. Fix hardware E (Handle) to Part 7 and 8 with screw L.

Step 10: Fix Part 7 and 8 to Part 2 and 3 with screw L. Fix hardware K (Magnetic Catch Plate) to Part 7 and 8 with screw U.

Step 11: Put Part 5 (Shelf) into the cabinet. Insert hardware G (Shelf Support Pin) into the screw holes on Part 2 and 3 to support the shelf.

Step 12: Use screw J to fix hardware T (Anti-Tip Bracket) to the corners on the back of the cabinet.

Step 13: Fix hardware Q (Anti-Tip Strap) to Part 1 (Top Panel) with hardware P (Screw) and O (Washer).

Step 14: Fix hardware S (Wall Anchor) to the wall. Fix hardware Q (Anti-Tip Strap) to hardware S with hardware P (Screw) and R (Screw) to secure the cabinet to the wall.