VEVOR ACO-005 (01) PDF Document

The VEVOR ACO-005 is a non-lubrication pump that provides very clean air. It can be used for aquatic breeding, restaurant and live aquatic product keeping, food packing, printing, spraying, electronic circuit board welding, supporting medical equipment, environmental equipment, and the use of gas stoves.

The VEVOR ACO-005 offers the following features:

1. Convenient to operate without oil, noise, and air pollution.

2. Cylinders and pistons are made of excellent materials, which are strong and durable and have little wear after a long time of working.

3. The structure is compact with innovative modeling, using high-quality materials, advanced manufacturing, small size, and lightweight.

4. Smooth operation.

5. Significant energy savings, as the power requirement for the VEVOR ACO-005 is about one-fifth of traditional structures, making it suitable for low-voltage exhaust pressure requirements.

Follow these steps to install and connect the VEVOR ACO-005:

1. Plug in the VEVOR ACO-005.

2. Connect the hose to the VEVOR ACO-005.

3. Plug the distributor into the hose.

4. Plug the soft tube into the distributor.

5. Plug the stop valve into the soft tube.

The working environmental temperature for the VEVOR ACO-005 should be within 0 degrees Celsius to 35 degrees Celsius. Maintain good ventilation and smoothness to prevent excessive temperature rise. The VEVOR ACO-005 should be protected from being rain-drenched, soaked with water, and should not be kept in the heat of the sun or a dusty environment.

Adhere to the following safety guidelines for the VEVOR ACO-005:

1. Do not pull or drag the VEVOR ACO-005 with the power line.

2. When pulling out the plug, hold the plug itself; do not pull the power cord.

3. Do not cut and replace the power plug by yourself.

4. Do not operate the VEVOR ACO-005 if the power line or the shell is damaged.

5. Disassembling and dismounting of the VEVOR ACO-005 by non-professionals is not allowed.

6. If the VEVOR ACO-005 drops into water, cut off the power supply before removing it. Hand it over to professionals for check and maintenance.

7. Electrical shock hazard: Do not touch the VEVOR ACO-005 with wet hands or while standing on a wet surface. Always use it in a dry environment and plug it into a properly grounded outlet.

8. Fire hazard: Do not use the VEVOR ACO-005 near flammable or combustible materials. Keep it away from sources of heat or sparks, such as flames, cigarettes, or electrical appliances.

9. Explosion hazard: Do not use the VEVOR ACO-005 with flammable, explosive, or poisonous gases. Always check the safety data sheet of the gas before using it. Do not exceed the specified pressure range.

10. Corrosion hazard: Do not use the VEVOR ACO-005 with gases that can corrode metals. Check gas compatibility with the materials of the VEVOR ACO-005. Use protective gloves and eyewear when handling corrosive materials.

Clear the filter sponges of the VEVOR ACO-005 at least once every month. If you are not going to use the VEVOR ACO-005 for a long time, cut off the power and place it in a ventilated area. Operate it for about ten minutes every month to ensure it is not broken and can run smoothly when needed.

Refer to the following troubleshooting table for the VEVOR ACO-005:

The technical specifications for the VEVOR ACO-005 are as follows:

Yes, the VEVOR ACO-005 must be installed flatly 20 centimeters above the water level and kept immovable to prevent liquid from flowing back and causing the VEVOR ACO-005 to break.

The VEVOR ACO-005 generates heat during operation, which can slightly warm the air and water. If temperature sensitivity is critical for your aquatic environment, it is recommended to pass the air tube through a simple chiller water tank before it enters the aquarium to prevent an increase in the aquarium temperature.