TP-LINK TAPO D210 (01) PDF MANUAL

• 2K 3MP Ultra-Clear Images – Always know what happens in front of your door through the Tapo app. With the spotlight and 2K 3MP resolution, check all the fine details captured even in low-light environments.

• 160° Ultra-Wide Diagonal FOV* – Receive head-to-toe views even when visitors stand too close to the doorbell with a 160° ultra-wide diagonal FOV.

• 6400mAh Battery Life – The equipped 6400mAh rechargeable battery extends the doorbell’s use.

• Color Night Vision – Reveals high-fidelity details and color at night with the spotlight.

• Quick Response – Respond to your deliveries without saying a word with customizable responses through the Tapo app.

• Multiple Ways to Answer – With two-way audio or a recorded quick response, communicate directly with your deliveries through the Tapo app.

• Flexible Storage Choices – Save recorded videos on the microSD card† (up to 512 GB) or by using Tapo Care** cloud storage services.

• Two-Way Audio – Enables communication through a built-in microphone and speaker.

• IP65 Weatherproof – Offers excellent waterproof and dustproof performance for outdoor scenarios.

• Free Al Detection – Enjoy free AI detection to identify people and vehicles, and notify you as needed.

Before installing the new doorbell, remove your existing doorbell, and determine if you need a mounting wedge to adjust the viewing angle of the doorbell.

1. Install the doorbell on a flat and clean wall.

2. The doorbell should be placed 1.2 m (4 ft) above the ground.

3. (Optional) Use the included 15° mounting wedge for a more focused view from a specific side. You can also flip the wedge 180° to change the angle.

4. Avoid placing the doorbell close to a side wall in the field of view. If you must, use the mounting wedge to adjust the viewing angle to reduce reflected light from the wall for better night vision performance.

This option is applicable for tile, glass, marble, metal, stainless steel, and smooth wall surfaces.

Required Accessories: Mounting Bracket, 3M Adhesive.

Optional Accessories: Mounting wedge, Mounting Wedge Screws ×4.

1. Attach the included adhesive to the back of the bracket or the wedge. If you use the wedge to adjust the angle, first affix the bracket and the wedge with screws. Note: The adhesive is for one-time use. Avoid re-using the adhesive to ensure its adhesion.

2. Wipe off the dust from the surface, stick the bracket or wedge with adhesive to a clean wall, and press it down for 15 seconds to ensure the bracket is firmly attached.

3. Then starting from the bottom, attach the doorbell to the bracket.

Required Accessories: Mounting Template, Mounting Bracket, Mounting Screws ×2, Anchors ×2.

Optional Accessories: Mounting wedge, Foam Pad.

1. Stick the mounting template to the desired place. Drill two holes according to the template. The drill bit size should be Φ=6 mm (15/64 in.).

2. Insert two anchors into the holes. Use the mounting screws to affix the bracket (or wedge with bracket if you use the wedge to adjust angle) over the anchors. Note: When mounting to uneven walls, stick the foam pad on the back of the wedge.

3. Starting from the bottom, attach the doorbell to the bracket.

If you have trouble attaching the doorbell or it causes false anti-theft alarms, check if you overtightened the screws that the bracket bent. Adjust the depth of the screw and reinstall the doorbell.

After installing the doorbell, follow the steps below to set up the doorbell and pair with the chime.

Step 1. Download Tapo App

Get the Tapo app from the App Store or Google Play.

Step 2. Log In

Open the app, and log in with your TP-Link ID. If you don’t have an account, create one first.

Step 3. Add Your Camera

Tap the ‘⊕’ button in the app and search for your model. Follow the app instructions to set up your doorbell. Then plug in your chime and pair with the doorbell.

Your doorbell can be paired with multiple chimes following the same steps. You can also find the instructions later in settings.

Amazon Frustration-Free Setup can help connect and set up Tapo smart devices in fewer steps, without having to remember and re-enter your Wi-Fi password on each device.

To use this feature, confirm the following:

• The new Tapo device supports Amazon FFS.

• The new Tapo device is purchased from Amazon.

• You have an Amazon FFS enabled Alexa device or router.

• You have saved your Wi-Fi information to Amazon by using Alexa echo.

• Your Tapo device and router are on the same network as your Alexa echo.

If the LED does not turn solid white after a long time, you can try to add the Tapo device manually. Press the Reset button on your Tapo device once. Then open the Tapo app, tap the + button on the page, select your device model, and follow the app instructions.

1. Open the Amazon Alexa app. Then tap More and select Skills & Games.

2. Enter Tapo in the search bar and choose Tapo.

3. Tap the ENABLE TO USE button.

4. Log in with your TP-Link ID that has bound to your Tapo device, and tap Authorize. After authorized successfully, the message “Tapo has been successfully linked” will come up.

5. Plug in your Tapo device and the setup will complete automatically in two minutes. For setting up more Tapo devices, just plug in and enjoy!

If this device does not display on the Home page in the Tapo app, try setting it up manually. Tap the + button on the page, select your device model, and then follow the app instructions.

After setup, your device will be listed on the Home page. You can tap your device to manage it.

1. Home Page

You can check your battery, favorite/unfavorite, and remove your device on the Home page.

2. Status Page

Tap your device to enter its Status page. On this page, you can:

• Watch multiple Tapo cameras/doorbells simultaneously.

• Take a screen shot.

• Record a clip.

• Talk to your visitors.

• Enable/disable Privacy Mode.

• Turn on/off spotlight.

• Play back event recordings and check the photos and videos you take yourself.

• Switch to landscape mode.

• Make a video call.

• Adjust the volume.

• Quickly select a preset response to communicate with visitors.

• Choose whether to have the tag when people or vehicles are detected.

From the Status page, tap the settings icon to go to the Device Settings page. Then select Detection. Here you can set when to wake up your doorbell, and the detection zones and sensitivity for each detection type.

• Wake-up Settings: Choose when the doorbell wakes up (Event Detected or Doorbell Pressed).

• Wake-up Sensitivity: Adjust the sensitivity for wake-up triggers. Higher sensitivity results in easier wake-up and more notifications.

• Motion Detection: Detect in real-time whether there is motion within the camera’s view. You can set detection zones and adjust sensitivity. Increased sensitivity results in fewer missed recordings; lower sensitivity results in fewer unwanted recordings.

• Person, Pet, and Vehicle Detection: Enable or disable specific detection types.

From the Device Settings page, go to Battery Status. Here you can:

• View the current battery level.

• Choose whether to show the battery status and percentage on Live View.

• Set the working mode (High Performance, Balanced, Power Saving, or Custom).

• Enable Auto Power Saving Mode to automatically switch to Power Saving Mode when the battery drops below 10%.

• Add a compatible solar panel as a power supply.

• Check battery usage and wake-up times for the past 7 or 30 days.

From the Device Settings page, go to Doorbell. Here you can configure:

• Doorbell Ring: Set the ringtone and volume of your doorbell.

• Paired Chimes: Check paired chimes/hub and add new ones.

• Doorbell Video Call: When someone presses the doorbell, you’ll receive a ring call if the Tapo app is already open on your screen. If the Tapo app is running in the background, you will receive a notification of the incoming call. When disabled, you will only receive message notifications.

• Anti-theft Alarm: When enabled, an alarm will be triggered once the doorbell is removed from the wall. Device resetting via the Reset button is not allowed when this feature is on. Do not turn on this feature if you haven’t installed the doorbell.

When the alarm is triggered, the doorbell will:

[Details from the app screen in the PDF, which are expandable but not shown in the image, would be listed here.]

How to dismiss the alarm?

[Details from the app screen in the PDF, which are expandable but not shown in the image, would be listed here.]

How to pause the alarm?

[Details from the app screen in the PDF, which are expandable but not shown in the image, would be listed here.]

From the Device Settings page, go to Storage & Recording. Here you can check your microSD card status, set the clips settings, and choose whether to record sound during recording.

• microSD Card Recording: Enable or disable recording to a local microSD card.

• Record Sound: When disabled, your camera will not record any sound.

• Clip Settings:

– Retrigger Time: Set intervals between event-triggered recordings.

– Record Buffer: When motion is no longer detected, the camera will keep recording for the set time.

– Maximum Clip Length: Set the maximum length for a single clip. Longer recordings will be divided into multiple clips.

* You can extend the battery life by setting a longer retrigger time and reducing the record buffer and clip length.

From the Device Settings page, go to Video & Display. Here you can adjust:

• Night Mode Settings: Set the recording effect at night. Options include Infrared Mode (black-and-white), Full-Color Mode (uses spotlight), and Doorbell Mode (spotlight on ring, otherwise infrared).

• Video Quality: Set the video resolution for the doorbell.

• Privacy Zones: Customize zones that cannot be viewed or monitored to protect your privacy.

• On-screen Display Info: Customize information that overlays the doorbell’s footage, such as a timestamp and custom text.

• Display Tag on Screen: Display the detection tag on your screen.

If you have turned on the spotlight on Live View, you can adjust the brightness. Go to Device Settings > Spotlight Settings. Here you can adjust the brightness level from 1 to 5.

When enabled, the streaming and recording feature will be temporarily unavailable. You can toggle this on or off from the Device Settings page.

Go to Device Settings > Notifications. Here you can choose what type of activity notifications you want to receive. You can enable/disable Activity Notifications, set the Activity Type (e.g., person, pet, vehicle), and set a Schedule for when you receive them.

Go to Device Settings > Share Device. You can tap Share to invite your family members to manage the smart device together. When enabled, streaming and recording feature will be temporarily unavailable for the shared user.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• Never touch the product with wet hands.

• Do not disassemble, repair or modify the product.

• Do not use the device where wireless devices are not allowed.

• Do not use the product if the casing has been broken. Danger of electric shock.

• Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.

• Do not place near automatically controlled devices such as fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.

• Observe restrictions on using wireless products in fuel depots, chemical plants or when blasting operations are in progress.

• Do not use liquid to clean the product. Only use a dry cloth.

• Never put metal objects inside the product. If a metal object enters the product turn off the circuit breaker and contact an authorised electrician.

• This product is not intended to be used when providing medical care. Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids to determine if they are adequately shielded from external RF (radio frequency) energy.

• Do not use this product in health care facilities. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

• Do not use this product near water for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

• The product should be kept free from excessive smoke, dust or high temperature and vibration.

• This product should not be exposed to direct sunlight.

• Do not place heavy objects on top of the product.

• This product may interfere with other electronic products such as TV, radios, personal computers, phones or other wireless devices.

• This equipment shall be installed at a height of fewer than 2 meters when sticking to a clean wall.

• Doorbell Operating Temperature: -20 °C ~ 45°C (-4°F ~ 113°F)

• Chime Operating Temperature: 0 °C ~ 40°C (32°F ~ 104°F)

• Maximum installation height: 6ft (2m)

• Please use the original power supply or only the power type specified for this product.

• Before cleaning this product, please unplug the power cord. Do not use liquid, aerosol cleaners or a damp cloth for cleaning.

• Pay attention to moisture, do not spill water or other liquids on this product.

• The slots and openings are for ventilation to ensure reliable operation of the product and to prevent overheating, do not block or cover the openings.

• Do not place this product near a heat source. Unless there is proper ventilation, it should not be placed in a closed location.

• Do not open the case or repair it yourself. If the product is faulty, please contact the original factory or agent.