TOSHIBA E-STUDIO9029A (01) PDF MANUAL

Press [Stop] on the touch panel.

Copying or scanning stops.

Press [Job Cancel] on the touch panel to stop copying.

Press [Next Copy] on the touch panel or the [START] button on the control panel to restart.

Even if copying is in progress or “Ready (Warming Up)” is displayed on the touch panel, you can scan the next original (auto job start).

1. Set the number of copy sets and the copy modes as required.

2. Press the [START] button on the control panel.

You can confirm which jobs are in waiting on the touch panel or cancel them as required. For details, see the reference below:

Information About Equipment – Information About Equipment – Confirming Job Statuses of Printing/Copying/Scanning/Faxing – Confirming jobs in progress or ones in waiting

Press [Stop] on the touch panel to stop a job while originals are being scanned.

When you press [Job Cancel] on the touch panel or the [FUNCTION CLEAR] button on the control panel while the scanning is being paused, the scanning will end. (In this case, the data which were scanned before the job was paused will be copied.) To restart the scanning, press the [START] button.

When you scan the next original as a priority copying job, it is carried out immediately after the job in progress is finished (priority job).

Up to 10 jobs can be registered as priority ones.

You can interrupt the copy job in progress to make other copies (interrupt copying).

1. Press [Interrupt Priority] and select [Interrupt].

2. Select other copy modes as required.

3. Press the [START] button.

The following functions cannot be used together with interrupt copying:

Cover sheet copying, Sheet insertion copying, Job build, Store to e-Filing, Copy & File

When you make a large amount of copies, you can check if they will be made exactly as you desire by copying only one set before copying them all (proof copy). Then you can change the modes or settings (e.g. the number of copy sets, receiving tray, page number, time stamp, sort, stapling, hole punching) after checking the proof copy.

1. Select the number of copy sets and copy modes.

2. Press [Proof Copy] on the touch panel.

3. Press the [START] button on the control panel.

4. Change the number of copy sets and copy modes as required after checking the proof copy.

5. Press the [START] button on the control panel.

The mode will be changed to [Sort] automatically.

You can specify the orientation of the placed originals.

1. Press a paper direction button on the Basic menu, matching the orientation of the placed original.

This setting can be also specified in “Finishing mode” or “Duplex copying mode”.

When you change the orientation on different setting screens, the last specified setting is applied.

This equipment detects the size of an original and selects paper of the same size automatically.

1. Press [APS] on the touch panel.

2. Select other copy modes as required, and then press the [START] button on the control panel.

Follow the directions.

You need to select paper by yourself when copying the following originals whose sizes cannot be detected correctly:

1. Press the drawer button corresponding to the desired paper size.

2. Select other copy modes as required, and then press the [START] button on the control panel.

You can copy or scan a set of originals whose sizes are individually different, using the ADF with the mixed size function.

1. Press [Zoom] on the Basic menu.

2. Press [Mixed Size].

3. Select a paper size.

4. Select other copy modes as required, and then press the [START] button on the control panel.

Remove the original from the ADF and change its direction accordingly.

When you place recycled paper, thick paper in the drawer, set the thickness and attribute into this equipment. To learn how to place paper and specify the paper type, see the reference below:

Preparation of Paper (e-STUDIO6525AC Series/e-STUDIO6528A Series) – LOADING PAPER – Loading Paper in Drawers

Preparation of Paper (e-STUDIO7527AC Series/e-STUDIO9029A Series) – LOADING PAPER – Loading Paper in Drawers

After setting the thickness and attributes for a drawer, set it to feed paper and make copies.

Thin paper, sticker labels, or special paper can be used to make copies by using the bypass tray.

Place such paper on the bypass tray and set the thickness and attributes into this equipment before you start copying. To learn how to place paper and specify the paper type, see the reference below:

Preparation of Paper (e-STUDIO6525AC Series/e-STUDIO6528A Series) – LOADING PAPER – Loading Paper on the Bypass Tray

Preparation of Paper (e-STUDIO7527AC Series/e-STUDIO9029A Series) – LOADING PAPER – Loading Paper on the Bypass Tray

When you make copies on OHP film, sticker labels, envelopes, or non-standard size paper, place the copy paper on the bypass tray. Bypass copying is also recommended for copying on standard size paper which is not set in any of the drawers.

• The height of the paper must not exceed the indicator on the side guides.
• When you use more than one sheet of paper, fan the sheets well before placing them on the bypass tray.
• Do not push paper into the entrance of the bypass feeder. This could cause a paper misfeed.
• When you copy on sheets of OHP film, remove the copied OHP film one sheet at a time as they exit onto the receiving tray. If the sheets of OHP film pile up, they may get curled and may not be projected properly.

If you place the originals on the ADF for bypass copying and do not set the paper size, the originals will be copied upside down. Be sure to set the paper size when you wish to do bypass copying.

Bypass copying stops when the paper placed on the bypass tray runs out during copying, even if the paper of the same size is in any of the drawers. Copying restarts when paper is supplied to the bypass tray.

When bypass copying has been completed, the [FUNCTION CLEAR] button on the control panel blinks. Press this button to switch bypass copying to normal copying using the drawers.

(Even if you do not press the [FUNCTION CLEAR] button, the bypass copying mode will be cleared when the automatic function clear mode kicks in after a specified period of time.)

1. Place paper on the bypass tray.

2. Select the same size button under “Copy” as that of the paper you placed on the bypass tray.

3. Press [Paper Type] on the touch panel if the paper type of the paper you placed on the bypass tray is other than plain paper.

4. Select the paper type, and press [OK].

5. After setting the paper size and type, press [OK].

6. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original(s) and paper on the bypass tray.

2. Press [Size Setting] on the touch panel.

3. Press the button of the same size as the paper you placed on the bypass tray.

4. Press [Other] under “Copy”.

5. Press [Paper Type] if the paper you placed on the bypass tray is other than plain paper.

6. Select the paper type and press [OK].

7. After setting the paper size and paper type, press [OK].

8. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original on the original glass.

2. Place paper on the bypass tray.

3. Press [Size Setting] on the touch panel.

4. Press the button of the same size as the envelope you placed on the bypass tray.

5. Press [Other] under “Copy” and press [OK].

6. Select other copy modes as required, and then press the [START] button on the control panel.

You can specify the size of non-standard size paper and copy it.

1. Place the original.

2. Place paper on the bypass tray.

3. Press [Custom Paper] on the touch panel.

4. Key in the dimension, and press [OK].

5. Select other copy modes as required, and then press the [START] button on the control panel.

The exit tray currently selected is displayed on the equipment status indication area. To change the exit tray, press [Exit Tray]. Every time you press this, the display changes from the exit tray of the equipment, each exit tray of the finisher and Job Separator, and automatic selection in this order.

You can switch the color mode. There are 3 color modes as shown below.

Full Color: All originals are copied in full colors. (Default)

Black: All originals are copied in black and white.

Auto Color: The equipment automatically judges the type of each color on originals. Colored originals are copied in full colors and black-and-white originals are copied in black and white.

Press any of [Full Color], [Black] or [Auto Color] on the touch panel.

When you select [Auto Color], some originals may not be copied exactly as they look, such as the cases shown below. Select either [Full Color] or [Black].

• When color originals are copied in black:
• Example:
• Originals whose colored area is extremely small
• Originals which are completely black
• Originals whose colors are light
• When black originals are copied in full colors:
• Example:
• Yellowish originals
• Originals with a colored background

This equipment detects the density level of originals and automatically adjusts the density level of the copied image to the optimal one. Alternatively, you can manually adjust it to the desired level.

Press [Auto] on the touch panel.

Press either or to select the desired density level.

Specify the copy paper size in advance so that this equipment will detect the original size and automatically select the optimal reproduction ratio to the copy paper size.

1. Press [Zoom] on the Basic menu.

2. Select the desired paper size, press [AMS] and then [OK].

3. Place the original(s).

If you want to select a size other than the following for the original size and copy paper size, you need to register the size as “Other” following the procedures below. Once you register this size, it will be specified every time you press [Other] on the touch panel.

1. Press [Size Setting] on the touch panel.

2. Select the desired size.

1. Follow the same procedure noted in steps 1 to 3 in the reference below:

2. Register dimensions.

Select a desired memory number and enter the values in [Length] and [Width].

1. Press [Zoom] on the Basic menu.

2. Press the buttons below to select the desired reproduction ratio.

3. Select the desired size, and then press [OK].

1. Press [Zoom] on the Basic menu.

2. Press [Photo Zoom].

3. Select the original size.

4. Select the desired copy paper size, and then press [OK].

5. Select other copy modes as required, and then press the [START] button on the control panel.

6. Place the next original, and then press [Next Copy] on the touch panel or the [START] button on the control panel.

7. When the scanning of all the originals is finished, press [Job Finish] on the touch panel.

You can select the exit tray if the finisher or the Job Separator is installed.

When you make more than one set of copies, they can be made to exit in the same page order as that of the originals. This mode is called the sort mode. Copies can also be made to exit grouped by page. This mode is called the group mode.

1. Press [Finishing] on the Basic menu.

2. Select [Sort] or [Group], and then press [OK].

3. Key in the desired number of copies on the Basic menu.

When you make more than one set of copies, one set can be made to exit on top of another set, alternating in portrait and landscape directions. This mode is called the rotate sort mode. Use 2 drawers and 2 stacks of paper of the same size. Place one stack of paper in one drawer in a portrait direction and place the other in another drawer in a landscape direction before you start copying.

1. Press [Finishing] on the Basic menu.

2. Select [Rotate Sort], and then press [OK].

3. Key in the desired number of copies on the Basic menu.

When you make more than one set of copies, the copied paper can be automatically stapled set by set. This mode is called the staple sort mode. You can choose from 4 different stapling positions.

1. Press [Finishing] on the Basic menu.

2. Press the button for the staple position, select the direction that matches the original you set from “Original Direction”, and press [OK].

You can punch copied paper when the Hole Punch Unit is installed on the Finisher. You can choose from two positions of holes.

1. Press [Finishing] on the Basic menu.

2. Select [Hole Punch] and [Original Direction], and then press [OK].

You can copy a 1-sided original to a 2-sided copy or vice versa, or copy a 2-sided original to a 2-sided copy. This is useful when you want to save the paper, or when you want to copy a book-type original maintaining the same page order.

1. Press [2-Sided] on the Basic menu.

2. Select the desired mode and original direction, and then press [OK].

[1->1 Simplex]: 1-sided original to 1-sided copy

[2->1 Split]: 2-sided original to 1-sided copy

1. Press [2-Sided] on the Basic menu.

2. Select the desired mode, book or tablet of original and paper, and original direction, and then press [OK].

[1 -> 2 Duplex]: 1-sided original to 2-sided copy

[2 -> 2 Duplex]: 2-sided original to 2-sided copy

You can make 2-sided copies from book-type originals such as books or catalog as in the same page order.

1. Press [2-Sided] on the Basic menu.

2. Select [Book -> 2].

3. Select the start page to be scanned and page layout.

4. Press [OK].

5. Press the drawer button corresponding to the desired paper size.

6. Select other copy modes as required.

7. Place