TOSHIBA E-STUDIO3525AC (01) PDF MANUAL

Make copies following the procedure below:

1. Make sure that paper is placed in the drawer(s).
2. Place the original(s).
3. Enter the desired number of copies on the touch panel if you want more than one copy.
4. Select the copy modes as required.
5. Press the [START] button on the control panel. Copying starts. The paper exits with its copied side down.

You can specify the orientation of the placed originals.

1. Press a paper direction button on the Basic menu, matching the orientation of the placed original.

The paper size is automatically detected when you place paper in the drawer(s).

This equipment detects the size of an original and selects paper of the same size automatically.

1. Press [APS] on the touch panel.
2. Select other copy modes as required, and then press the [START] button on the control panel.

You need to select paper by yourself when copying the following originals whose sizes cannot be detected correctly:

• Highly transparent originals (e.g. OHP film, tracing paper)
• Totally dark originals or originals with dark borders
• Non-standard size originals (e.g. newspapers, magazines)

1. Press the drawer button corresponding to the desired paper size.
2. Select other copy modes as required, and then press the [START] button on the control panel.

You can copy or scan a set of originals whose sizes are individually different, using the ADF with the mixed size function.

The original sizes that can be mixed are as follows:

North America: LD, LG, LT, LT-R, COMP

Other than North America: A3, A4, A4-R, B4, B5, FOLIO

1. Press [Zoom] on the Basic menu.
2. Press [Mixed Size].
3. Select a paper size.
4. Select other copy modes as required, and then press the [START] button on the control panel.

When you place any special paper other than plain paper or that not used for normal copying, you need to set the thickness and attribute into this equipment.

When you place recycled paper, thick paper in the drawer, set the thickness and attribute into this equipment.

Thin paper, sticker labels, or special paper can be used to make copies by using the bypass tray.

Cover sheets or paper to insert a specific page can be prepared and copied in a drawer different from an ordinary drawer. Place paper in a drawer and set attribute as the paper type.

When you make copies on OHP film, sticker labels, envelopes, or non-standard size paper, place the copy paper on the bypass tray. Bypass copying is also recommended for copying on standard size paper which is not set in any of the drawers.

1. Place paper on the bypass tray.
2. Select the same size button under “Copy” as that of the paper you placed on the bypass tray.
3. Press [Paper Type] on the touch panel if the paper type of the paper you placed on the bypass tray is other than plain paper.
4. Select the paper type, and press [OK].
5. After setting the paper size and type, press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original(s) and paper on the bypass tray.
2. Press [Size Setting] on the touch panel.
3. Press the button of the same size as the paper you placed on the bypass tray.
4. Press [Other] under “Copy”.
5. Press [Paper Type] if the paper you placed on the bypass tray is other than plain paper.
6. Select the paper type and press [OK].
7. After setting the paper size and paper type, press [OK].
8. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original on the original glass.
2. Place paper on the bypass tray.
3. Press [Size Setting] on the touch panel.
4. Press the button of the same size as the envelope you placed on the bypass tray.
5. Press [Other] under “Copy” and press [OK].
6. Select other copy modes as required, and then press the [START] button on the control panel.

You can specify the size of non-standard size paper and copy it.

1. Place the original.
2. Place paper on the bypass tray.
3. Press [Custom Paper] on the touch panel.
4. Key in the dimension, and press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.

The exit tray currently selected is displayed on the equipment status indication area. To change the exit tray, press [Exit Tray]. Every time you press this, the display changes from the exit tray of the equipment, each exit tray of the finisher and Job Separator, and automatic selection in this order.

You can switch the color mode. There are 3 color modes as shown below.

Full Color: All originals are copied in full colors. (Default)

Black: All originals are copied in black and white.

Auto Color: The equipment automatically judges the type of each color on originals. Colored originals are copied in full colors and black-and-white originals are copied in black and white.

Press any of [Full Color], [Black] or [Auto Color] on the touch panel.

This equipment detects the density level of originals and automatically adjusts the density level of the copied image to the optimal one. Alternatively, you can manually adjust it to the desired level.

Press [Auto] on the touch panel.

Press either or ▸ to select the desired density level.

You can change the reproduction ratio of copied images in the following procedures:

• Automatic Magnification Selection (AMS)
• Specifying both original size and copy paper size separately
• Specifying reproduction ratio manually
• Copying photo originals in the optimal reproduction ratio for copy paper size (Photo Zoom)
• Reducing images to scan the entire original, including the edges (Full Image)

Specify the copy paper size in advance so that this equipment will detect the original size and automatically select the optimal reproduction ratio to the copy paper size.

1. Press [Zoom] on the Basic menu.
2. Select the desired paper size, press [AMS] and then [OK].
3. Place the original(s).

1. Press [Zoom] on the Basic menu.
2. Select the desired sizes for the original and copy paper, and then press [OK].

If you want to select a size other than the following for the original size and copy paper size, you need to register the size as “Other” following the procedures below. Once you register this size, it will be specified every time you press [Other] on the touch panel.

1. Press [Size Setting] on the touch panel.
2. Select the desired size.

1. Press [Zoom] on the Basic menu.
2. Press the buttons below to select the desired reproduction ratio.
3. Select the desired size, and then press [OK].

1. Press [Zoom] on the Basic menu.
2. Press [Photo Zoom].
3. Select the original size.
4. Select the desired copy paper size, and then press [OK].
5. Select other copy modes as required, and then press the [START] button on the control panel.
6. Place the next original, and then press [Next Copy] on the touch panel or the [START] button on the control panel.
7. When the scanning of all the originals is finished, press [Job Finish] on the touch panel.

1. Press [Custom] on the touch panel.
2. Key in the size of the original, and press [OK].

1. Press [Zoom] on the Basic menu.
2. Select sizes for the original and copy paper, and press [OK].
3. Press [Full Image] on the Edit menu.

You can make a copy with a scanned image reduced and moved to the center of the paper.

1. Press [Zoom] on the Basic menu.
2. Select a desired reproduction ratio.
3. Press [Centering Copy].
4. Press [OK] on the displayed centering copy screen.
5. Press [OK] on the [Zoom] screen.

See the table below for each finishing mode.

When you make more than one set of copies, they can be made to exit in the same page order as that of the originals. This mode is called the sort mode. Copies can also be made to exit grouped by page. This mode is called the group mode. When the sort and group mode is selected, copies automatically exit in the offset mode (shift exiting) by shifting the exit position for each sorted set.

1. Press [Finishing] on the Basic menu.
2. Select [Sort] or [Group], and then press [OK].
3. Key in the desired number of copies on the Basic menu.

When you make more than one set of copies, one set can be made to exit on top of another set, alternating in portrait and landscape directions. This mode is called the rotate sort mode. Use 2 drawers and 2 stacks of paper of the same size. Place one stack of paper in one drawer in a portrait direction and place the other in another drawer in a landscape direction before you start copying. When the rotate sort mode is selected, copies automatically exit in the offset mode (shift exiting).

1. Press [Finishing] on the Basic menu.
2. Select [Rotate Sort], and then press [OK].
3. Key in the desired number of copies on the Basic menu.

When you make more than one set of copies, the copied paper can be automatically stapled set by set. This mode is called the staple sort mode. You can choose from 4 different stapling positions.

1. Press [Finishing] on the Basic menu.
2. Press the button for the staple position, select the direction that matches the original you set from “Original Direction”, and press [OK].

You can copy more than one original and bind them in a booklet format (Magazine sort). With the Saddle Stitch Finisher, you can also have the copied booklet folded at its center (Center fold) and besides stapled (Saddle stitch).

1. Place the original(s).
2. Press [Finishing] on the Basic menu.
3. Select the direction that matches the direction you set from “Original Direction”, and press [Binding].
4. Select a binding mode and press [OK].
5. When you select [Magazine Sort], [Magazine Sort & Center Fold], or [Magazine Sort & Saddle Stitch], specify the binding margin and press [OK].
6. Combine the copied paper if the center fold mode or magazine sort & center fold mode is used.

You can punch copied paper when the Hole Punch Unit is installed on the Finisher. You can choose from two positions of holes.

1. Press [Finishing] on the Basic menu.
2. Select [Hole Punch] and [Original Direction], and then press [OK].

1. Press [2-Sided] on the Basic menu.
2. Select the desired mode and original direction, and then press [OK].

1. Press [2-Sided] on the Basic menu.
2. Select the desired mode, book or tablet of original and paper, and original direction, and then press [OK].

You can make 2-sided copies from book-type originals such as books or catalog as in the same page order.

1. Press [2-Sided] on the Basic menu.
2. Select [Book -> 2].
3. Select the start page to be scanned and page layout.
4. Press [OK].
5. Press the drawer button corresponding to the desired paper size.
6. Select other copy modes as required.
7. Place the original on the original glass.
8. Press the [START] button on the control panel. Once the pages are scanned, set the next ones on the original glass.
9. When all the pages have been scanned, press [Finished].

You can make copies with the optimal image quality by selecting the following modes for your original. The selectable original mode differs depending on the color mode as shown in the table below. Select the color mode first, and then the original mode. Moreover, the selectable original mode varies depending on the model.

1. Press [Original Mode] on the Basic menu.
2. Select the original mode, and then press [OK].

You can display the Edit menu by pressing the [Edit] tab on the touch panel when you want to use various editing functions.

1. Press [Image Shift] on the Edit menu.
2. Select the type of binding margin.
3. Adjust the width of the binding margin, and press [OK].
4. Press [OK].

1. Press [Image Shift] on the Edit menu.
2. Press [Book].
3. Adjust the width of the binding margin, and press [OK].
4. Press [OK].

You can whiten the edge of the copied image when a shadow-like dark part appears on it. This function is called “edge erase”. It is useful when you want to make the copied image neat and clear if the edge of the original is dirty or torn.

1. Press [Edge Erase] on the Edit menu.
2. Adjust the width of the part to be erased, and press [OK].

You can whiten the center of the copied image when a shadow-like part appears on it.

1. Select the drawer for the desired paper size.
2. Press [Book Center Erase] on the Edit menu.
3. Adjust the width of the part to be erased, and press [OK].
4. Place the original on the original glass.

You can copy the 2 facing pages of a book-type original or 2 original sheets placed side by side onto 2 separate sheets of paper or on both sides of 1 sheet of paper. This function is called “dual page”. You do not have to shift the original on the original glass.

1. Press [Dual Page] on the Edit menu.
2. Press [1 Side] or [2 Side].
3. Select other copy modes as required.
4. Press the [Basic] tab to display the Basic menu, and then select A4, B5 or LT as the copy paper size.
5. Open the desired page of the original and place it on the original glass.