TOSHIBA E-STUDIO2521AC (01) PDF MANUAL

To stop copying, press [Stop] on the touch panel. Copying or scanning stops.

To restart copying, Press [Job Cancel] on the touch panel to stop copying. Press [Next Copy] on the touch panel or the [START] button on the control panel to restart.

Even if copying is in progress or “Ready (Warming Up)” is displayed on the touch panel, you can scan the next original (auto job start).

1. Set the number of copy sets and the copy modes as required.

2. Press the [START] button on the control panel.

You can confirm which jobs are in waiting on the touch panel or cancel them as required. For details, see the reference below:

Information About Equipment – Information About Equipment – Confirming Job Statuses of Printing/Copying/Scanning/Faxing – Confirming jobs in progress or ones in waiting

Press [Stop] on the touch panel to stop a job while originals are being scanned.

When you press [Job Cancel] on the touch panel or the [FUNCTION CLEAR] button on the control panel while the scanning is being paused, the scanning will end. (In this case, the data which were scanned before the job was paused will be copied.) To restart the scanning, press the [START] button.

When you scan the next original as a priority copying job, it is carried out immediately after the job in progress is finished (priority job).

1. Press [Interrupt Priority] and select [Priority].

2. Set the number of copy sets and the copy settings as required.

3. Press the [START] button. After the job in progress is finished, a priority copying job starts.

You can confirm the registered priority job on the touch panel. In addition, you can remove it. For details, see the reference below:

Information About Equipment – Information About Equipment – Confirming Job Statuses of Printing/Copying/Scanning/Faxing – Confirming jobs in progress or ones in waiting

When you make a large amount of copies, you can check if they will be made exactly as you desire by copying only one set before copying them all (proof copy). Then you can change the modes or settings (e.g. the number of copy sets, receiving tray, page number, time stamp, sort, stapling, hole punching) after checking the proof copy.

1. Select the number of copy sets and copy modes.

2. Press [Proof Copy] on the touch panel.

3. Press the [START] button on the control panel. Scanning starts. 1 set of copies will be printed out.

4. Change the number of copy sets and copy modes as required after checking the proof copy. Modes or settings such as the number of copy sets, the receiving tray, page number, time stamp, sort, stapling and punching can be changed.

5. Press the [START] button on the control panel.

You can specify the orientation of the placed originals.

1. Press a paper direction button on the Basic menu, matching the orientation of the placed original.

This equipment detects the size of an original and selects paper of the same size automatically.

1. Press [APS] on the touch panel.

2. Select other copy modes as required, and then press the [START] button on the control panel.

You need to select paper by yourself when copying the following originals whose sizes cannot be detected correctly:

• Highly transparent originals (e.g. OHP film, tracing paper)
• Totally dark originals or originals with dark borders
• Non-standard size originals (e.g. newspapers, magazines)

1. Press the drawer button corresponding to the desired paper size.

2. Select other copy modes as required, and then press the [START] button on the control panel.

When you place any special paper other than plain paper or that not used for normal copying, you need to set the thickness and attribute into this equipment.

When you place recycled paper, thick paper in the drawer, set the thickness and attribute into this equipment. To learn how to place paper and specify the paper type, see the reference below:

Preparation of Paper (e-STUDIO6525AC Series/e-STUDIO6528A Series) – LOADING PAPER – Loading Paper in Drawers

Preparation of Paper (e-STUDIO7527AC Series/e-STUDIO9029A Series) – LOADING PAPER – Loading Paper in Drawers

After setting the thickness and attributes for a drawer, set it to feed paper and make copies.

Thin paper, sticker labels, or special paper can be used to make copies by using the bypass tray.

Place such paper on the bypass tray and set the thickness and attributes into this equipment before you start copying. To learn how to place paper and specify the paper type, see the reference below:

Preparation of Paper (e-STUDIO6525AC Series/e-STUDIO6528A Series) – LOADING PAPER – Loading Paper on the Bypass Tray

Preparation of Paper (e-STUDIO7527AC Series/e-STUDIO9029A Series) – LOADING PAPER – Loading Paper on the Bypass Tray

Cover sheets or paper to insert a specific page can be prepared and copied in a drawer different from an ordinary drawer. Place paper in a drawer and set attribute as the paper type. For setting for attribute, see the reference below:

Preparation of Paper (e-STUDIO6525AC Series/e-STUDIO6528A Series) – LOADING PAPER – Doing Paper Settings – Setting paper type

Preparation of Paper (e-STUDIO7527AC Series/e-STUDIO9029A Series) – LOADING PAPER – Doing Paper Settings – Setting paper type

When you make copies on OHP film, sticker labels, envelopes, or non-standard size paper, place the copy paper on the bypass tray. Bypass copying is also recommended for copying on standard size paper which is not set in any of the drawers.

The operating procedure for bypass copying differs depending on the paper size to be used. See the table below for the operating procedure of each size.

1. Place paper on the bypass tray.

2. Select the same size button under “Copy” as that of the paper you placed on the bypass tray.

3. Press [Paper Type] on the touch panel if the paper type of the paper you placed on the bypass tray is other than plain paper.

4. Select the paper type, and press [OK].

5. After setting the paper size and type, press [OK]. The menu returns to the Basic menu.

6. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original(s) and paper on the bypass tray.

2. Press [Size Setting] on the touch panel.

3. Press the button of the same size as the paper you placed on the bypass tray.

4. Press [Other] under “Copy”.

5. Press [Paper Type] if the paper you placed on the bypass tray is other than plain paper.

6. Select the paper type and press [OK].

7. After setting the paper size and paper type, press [OK].

8. Select other copy modes as required, and then press the [START] button on the control panel.

1. Place the original on the original glass.

2. Place paper on the bypass tray.

3. Press [Size Setting] on the touch panel.

4. Press the button of the same size as the envelope you placed on the bypass tray.

5. Press [Other] under “Copy” and press [OK].

6. Select other copy modes as required, and then press the [START] button on the control panel. Copying starts.

You can specify the size of non-standard size paper and copy it.

1. Place the original.

2. Place paper on the bypass tray.

3. Press [Custom Paper] on the touch panel.

4. Key in the dimension, and press [OK].

5. Select other copy modes as required, and then press the [START] button on the control panel.

The exit tray currently selected is displayed on the equipment status indication area. To change the exit tray, press [Exit Tray]. Every time you press this, the display changes from the exit tray of the equipment, each exit tray of the finisher and Job Separator, and automatic selection in this order.

Press either or to select the desired density level.

1. Press [Zoom] on the Basic menu.

2. Select the desired paper size, press [AMS] and then [OK].

3. Place the original(s).

If you want to select a size other than the following for the original size and copy paper size, you need to register the size as “Other” following the procedures below. Once you register this size, it will be specified every time you press [Other] on the touch panel.

1. Press [Size Setting] on the touch panel.

2. Select the desired size.

1. Follow the same procedure noted in steps 1 to 3 in the reference below: P.37 “Bypass copying on non-standard size paper”

2. Register dimensions. Select a desired memory number and enter the values in [Length] and [Width]. After entering required information, press [Memory].

1. Press [Zoom] on the Basic menu.

2. Press the buttons below to select the desired reproduction ratio.

3. Select the desired size, and then press [OK].

1. Press [Custom] on the touch panel.

2. Key in the size of the original, and press [OK].

1. Press [Finishing] on the Basic menu.

2. Select [Sort] or [Group], and then press [OK].

3. Key in the desired number of copies on the Basic menu.

1. Press [Finishing] on the Basic menu.

2. Select [Rotate Sort], and then press [OK].

3. Key in the desired number of copies on the Basic menu.

1. Press [Finishing] on the Basic menu.

2. Press the button for the staple position, select the direction that matches the original you set from “Original Direction”, and press [OK].

1. Press [2-Sided] on the Basic menu.

2. Select the desired mode and original direction, and then press [OK].

1. Press [2-Sided] on the Basic menu.

2. Select the desired mode, book or tablet of original and paper, and original direction, and then press [OK].

1. Press [2-Sided] on the Basic menu.

2. Select [Book -> 2].

3. Select the start page to be scanned and page layout.

4. Press [OK]. The menu returns to the Basic menu.

5. Press the drawer button corresponding to the desired paper size.

6. Select other copy modes as required.

7. Place the original on the original glass.

8. Press the [START] button on the control panel. Once the pages are scanned, set the next ones on the original glass.

9. When all the pages have been scanned, press [Finished].

1. Press [Original Mode] on the Basic menu.

2. Select the original mode, and then press [OK].

You can display the Edit menu by pressing the [Edit] tab on the touch panel when you want to use various editing functions.

1. Press [Image Shift] on the Edit menu.

2. Select the type of binding margin.

3. Adjust the width of the binding margin, and press [OK].

4. Press [OK].

1. Press [Image Shift] on the Edit menu.

2. Press [Book].

3. Adjust the width of the binding margin, and press [OK].

4. Press [OK].

1. Press [Edge Erase] on the Edit menu.

2. Adjust the width of the part to be erased, and press [OK].

1. Select the drawer for the desired paper size.

2. Press [Book Center Erase] on the Edit menu.

3. Adjust the width of the part to be erased, and press [OK].

4. Place the original on the original glass.

1. Press [Dual Page] on the Edit menu.

2. Press [1 Side] or [2 Side].

3. Select other copy modes as required.

4. Press the [Basic] tab to display the Basic menu, and then select A4, B5 or LT as the copy paper size.

5. Open the desired page of the original and place it on the original glass.

6. Press the [START] button on the control panel. When the scanning of the opened pages is finished, open the next pages and place them.

7. When all the pages have been scanned, press [Finished].

1. Press [2 in 1/4 in 1] on the Edit menu.

2. Perform 2 in 1 / 4 in 1 setting, and press [OK].

You can select the various editing functions shown below for scanned images.

Trimming: You can select a certain area of an original and copy only the selected area.

Masking: You can mask a certain area of an original and copy only the unmasked area.

Mirror image: You can reverse an image like a mirror.

Negative/Positive reversal: You can reverse the light-and-dark of an image.

1. Press [Editing] on the Edit menu.

2. Select [Trim] or [Mask].

3. Place the original on the original glass with its face up.

4. Read the following 4 values to specify the area using the left and top scales on the original glass.

5. Key in the read values, and press [OK].

6. Place the original again on the original glass with its face down.

1. Press [Editing] on the Edit menu.

2. Select [Mirror] or [Neg/Pos], and then press [OK].

1. Place the paper for the cover sheets and specify the paper type.

2. Place the normal paper in the drawer(s).

3. Place the original(s).

4. Press [Cover Sheet] on the Edit menu.

5. Select the front and back cover settings, and then press [OK].

6. Press the [Basic] tab to display the Basic menu. Then select a drawer in which normal paper is placed (not the one for the cover sheets).

7. Select other copy modes as required, and then press the [START] button on the control panel.

8. Place the next original, and then press [Next Copy] on the touch panel or the [START] button on the control panel.

1. Place sheets for sheet insertion and specify the paper type.

2. Press [Sheet Insertion] on the Edit menu.

3. Select