SUNBEAM ELITE STYLE II T85B THROW (01) PDF Document

When setting up your SUNBEAM ELITE STYLE II T85B THROW, please follow these directions in the order they are given to ensure your product will work correctly. Do not turn on the product until it has been fully assembled.

Step 1. Connect the Control Cord connector and module securely. Locate the heated throw’s information label near the module. Connect the cord into the module at the bottom of the heated throw until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection.

Step 2. Plug the Power Cord into a 110-120 volt wall outlet.

CAUTION:

• Do not plug main power cord into the wall outlet until you have completely set up your heated product per the instructions.

• Disconnect power cord from wall before detaching control from heated product.

• Always make sure cords and controls are NOT trapped or pinched between bed slats, mattress, springs, against wall, foot board or bed frame, or between furniture, walls or chairs.

• Do not wrap control in throw when in use.

• Do not use with generator power.

Step 1. To turn on the SUNBEAM ELITE STYLE II T85B THROW, press the button in the middle of the control. The indicator light will glow, depending on which setting the heated throw is set, and the heated throw will begin to warm.

Step 2. To turn the heated throw OFF, press the button through the different settings until the temperature setting lights are not glowing.

CAUTION: ALWAYS turn the heated throw “OFF” and disconnect the power cord from the outlet when not in use.

The SUNBEAM ELITE STYLE II T85B THROW uses the Elite Style™ II control with the following features:

The “Auto-Off” feature on your SUNBEAM ELITE STYLE II T85B THROW is designed for conservation of energy by automatically turning your product off after 3 hours of continuous use.

CAUTION: Do not dry clean. Do not use bleach. Do not use wringer. Do not iron. Do not immerse control or cord in water or other liquids. Do not use mothballs or sprays of any kind. Do not reconnect the heated product until it is completely dry. We recommend washing before initial use.

Before Washing or Storing Your Heated Bedding Product:

1. Disconnect power cord from wall BEFORE detaching control cord from the heated product.

2. Ensure that no cords are still connected and none of the wires have worn through the fabric.

3. Carefully follow all washing instructions or your heated product may shrink and possibly cause a fire hazard.

Washing Instructions:

1. Machine wash in cold water, gentle cycle or hand wash.

Caution: Do not use commercial dryers or the dryers at your local laundromat. They get too hot and would damage the wiring of the heated product.

2. Tumble dry low, delicate cycle.

3. Remove the throw while still damp and gently stretch to its original size.

4. Drape the heated product over a clothesline or a shower rod. DO NOT use clothespins.

5. The heated product must be COMPLETELY dry before reconnecting the power plug or control plug.

Hang to Dry:

1. While still damp, gently stretch the throw back to its original size.

2. Drape the heated product over a clothesline or hang over a shower rod. DO NOT use clothespins.

3. The heated product must be COMPLETELY dry before reconnecting the power plug or control plug.

The following people should NOT use the SUNBEAM ELITE STYLE II T85B THROW:

• An infant

• A child

• An incapacitated or immobile person

• A paraplegic

• A quadriplegic

• A diabetic

• Anyone insensitive to heat such as a person with poor blood circulation

• Anyone who cannot clearly understand the instructions and/or operate the controls

Please stop using the heated product immediately. A damaged cord or malfunctioning control can be a hazard. Contact Consumer Care for assistance.

No. The control will feel warm to the touch when functioning properly.

Your SUNBEAM ELITE STYLE II T85B THROW is not a heating pad. It will not feel hot to the touch when laid out flat in a normal manner. Try the following fold test to see if it is operating properly:

1. Fold the warming throw 3 times over.

2. Make sure the control cord is connected to the module and then plug the power cord into an outlet.

3. Turn on your heated product, then turn the control to the highest setting and wait 5 to 7 minutes.

4. Put your hand between the folds and you should feel the throw warming up.

Caution: DO NOT continue the test for more than 7 minutes. DO NOT attempt to make any internal adjustments to this appliance. If you have tried all of the solutions above and the heated product still doesn’t work, stop using it immediately, disconnect the power cord and contact Consumer Care.

The control is designed to notify you in the event that a problem has been discovered by flashing the light on the control. Follow instructions on the flag tag to reset the control. First, check the heated product for visual damage. If no visual damage is found, unplug the system from the wall outlet. Check that the control is well-connected to the module. Plug the power cord into the wall outlet and turn the control On. If the product still does not operate after 2 or 3 times trying to reset, disconnect the power cord and contact Consumer Care.

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons. Misuse or failure to follow these warnings and instructions may cause overheating, fire, personal injury and/or property damage:

1. Be sure to read carefully all instructions before using this heated product.

2. Do not use this heated product with an infant, child, incapacitated or immobile person, paraplegic or quadriplegic, a diabetic, anyone insensitive to heat, such as a person with poor blood circulation, or anyone who cannot clearly understand the instructions and/or operate the controls.

3. Do not tuck in, pinch, flex or expose the wired heating area of this heated product.

4. Do not route electrical cords between the mattress and box spring. Do not allow the cords to be pinched. Do not use with damaged cords. Damaged cords can lead to overheating or fire.

5. Keep the control away from drafty areas that may become damp or wet such as an open window.

6. Do not use pins or other metallic means – They may damage the electric wiring.

7. Do not use if wet. If a spill occurs, turn heated product off, unplug, and dry before re-using.

8. Controller is not waterproof. Do not immerse in water or other liquids.

9. Be sure that this heated product is used only on an AC supply circuit of the proper voltage. Do not use with an extension cord. Do not use with generators, power converters or inverters.

10. Turn off or unplug this heated product when not in use.

11. Excessive heating may result from folding or bunching this heated product while in use.

12. Examine the heated product, cord and controller before each use for signs of wear or damage. If improper operation, wear or damage is observed, discontinue its use immediately, unplug it, and call Consumer Care.

13. For throw blankets: Do not use with rocking chairs, recliners, chairs with casters or wheels, or other furniture subject to movement.

14. Do not use this heated product on a waterbed, bunk bed, mechanically adjustable bed or a child’s crib/bed.

15. Do not use in conjunction with another electrically heated product.

16. Do not tuck in the supply cord or control in a sofa or other furniture. All portions of this heated product should be visible at all times.

17. Wrapping of cord around the controller may damage the cord. Loop loosely when storing. Allow to cool before storing and do not crease by placing items on top of it. Store in the original packaging, in a cool, dark, dry place.

18. Do not dry clean this heated product. Cleaning solvents may damage the insulation of the heating element. Improper laundering may cause problems with the heating wire, which can lead to fire.

19. Keep all dogs, cats and other pets away from this heated product. This is an electrical appliance that they can damage or be injured by.

20. If provided with a detachable controller, use only with the provided controller.

21. Do not use this heated product with analgesic creams, liniments, salve or ointment preparations. Skin burns could result.

22. Check with your healthcare provider before using with a pacemaker or any medical devices.

23. Not for hotel, motel, hospital or other institutional use.

The SUNBEAM ELITE STYLE II T85B THROW has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. If the plug fits loosely into the AC outlet or if the AC outlet feels warm do not use that outlet.