SISER JULIET SNAHDCJ12 (01) PDF DOCUMENT

The main components of the SISER JULIET SNAHDCJ12 are as follows:

1. Machine Head: The main operational head of the cutter.

2. Flip Cover: A protective cover for the machine.

3. Touch Screen: The interface for controlling the cutter.

4. Cutting Strip: A protective strip where the blade makes contact during cutting.

5. Tool Holder: Holds the cutting blade holder or marker adapter.

6. Feed Tray: Helps to stabilize the material being fed into the cutter.

7. Adjustable Pinch Rollers: Feeds material in and out of the cutter.

8. Grit Marks: Markers to guide the placement of pinch rollers for optimal traction.

9. Power Button: Turns the cutter on and off.

10. Pinch Roller Levers: Adjusts the tension of the pinch rollers.

11. USB-A Port: Used for connecting flash drives to the cutter.

12. USB-B Port: Used for connecting the cutter to a computer.

13. DC Power Port: The connection port for the power supply.

14. Roller Bar Lever: Locks down or releases material under the roller bar and allows pinch rollers to be adjusted.

15. Raised Feet: Lifts the cutter for stability and clearance.

The SISER JULIET SNAHDCJ12 includes the following accessories in its packaging:

• Marker Adapter

• 45° Blades

• 60° Blade

• Blade Holder

• USB Cord

• Power Cord and Power Supply

• 12″x12″ Cutting Mat

• Two sheets of 6″x12″ Siser® Heat Transfer Vinyl

• One Cover Sheet

Follow these steps to manually set up your SISER JULIET SNAHDCJ12:

1. Unpack: Remove all protective packaging from the cutter and its accessories. This includes the plastic clips from the pinch rollers.

2. Power On: Plug the round end of the power cord into the DC power port on the rear of the machine. Plug the opposite end into a standard electrical outlet. Press the power button to turn the cutter on.

3. Install Blade: Carefully remove the 45° blade from its packaging and insert it into the socket on the blade holder with the pointed side facing outwards.

4. Adjust Blade Depth: Twist the upper screw of the blade holder clockwise to expose less of the blade, or counterclockwise to expose more. The ideal length of the exposed blade is about the width of a credit card. Once adjusted, twist the inner screw to lock the blade in position.

5. Insert Blade Holder: Insert the blade holder into the tool holder on the machine head with the blade facing down. Turn the knob on the tool holder clockwise to tighten it.

6. Load Material: Lower the roller bar lever to adjust the pinch rollers. Position the rollers over the grit marks for optimal traction. Place your material or cutting mat under the rollers and align it. Raise the roller bar lever to secure the material or mat in place. The pinch roller levers can be flipped ‘up’ to increase tension or ‘down’ to ease tension.

7. Set Cut Settings: Tap ‘Cut Settings’ on the touch screen. Tap the current preset to view the menu. Select the preset that matches your material to automatically adjust the cut force and speed.

8. Perform a Test Cut: Tap ‘Test Cut’ to cut a small shape from your material. This ensures the cut settings are correct. After testing, select the ‘Home’ icon to return to the home screen.

When performing a test cut with your SISER JULIET SNAHDCJ12, you can identify the quality of the cut by observing the following:

• Bad Cut (Too Shallow): The cut is not deep enough and the material cannot be weeded. This means you need to increase the cut force (pressure).

• Bad Cut (Too Deep): The cut goes through both the material and the carrier sheet. This means you need to decrease the cut force (pressure).

• Good Cut: The cut goes through the material layer, but the carrier sheet is not cut through. This is the ideal result for proper weeding and application.

1. Connect USB Drive: Plug your USB flash drive into the USB-A port on the rear of the cutter.

2. Access USB Menu: On the touch screen, tap the ‘Settings’ button, then select ‘USB’ from the menu.

3. Select File: From the drop-down list, select the cut file you wish to use.

4. Position Blade: On the main screen, use the on-screen arrow buttons to move the blade to the desired starting position on your material.

5. Start Cutting: Once the blade is in position, tap the play button to begin cutting.

The Home Screen of the SISER JULIET SNAHDCJ12 provides the following options:

1. WiFi Indicator: Displays the status of the WiFi connection.

2. Directional Arrows: Moves the material and the machine head for positioning.

3. Play Button: Resumes a paused cut or recuts the last known design.

4. Tool Reorientation: Moves the tool holder back to its starting position.

5. Settings: Opens the main cutter settings menu.

6. Cut Settings: Opens the presets menu with adjustable cut settings for force and speed.

7. Test Cut: Performs a test cut at the tool holder’s current position.

When a cut job is running on your SISER JULIET SNAHDCJ12, the screen will display the following options:

1. Pause Button: Pauses the job at its current position.

2. Job Progress Bar: A circle that fills in to display the progress of the current job.

3. Cancel Button: Cancels the current job entirely.

From the ‘Cut Settings’ menu on the SISER JULIET SNAHDCJ12, you can adjust the following:

1. Back Button: Returns to the previous screen.

2. Home Button: Returns to the Home Screen.

3. Cutting Presets: Opens the preset cutting menu to choose settings for specific materials.

4. Cut Speed: Adjusts how fast the machine head moves during cutting.

5. Force: Adjusts how much pressure the machine head exerts, controlling the depth of the cut.

6. Update Preset: Overwrites the selected preset with the current settings you have adjusted.

The main ‘Settings’ menu on the SISER JULIET SNAHDCJ12 gives you access to the following sub-menus:

1. General Settings: Opens the menu for general cutter settings like LED brightness, alerts, and language.

2. WiFi: Opens the WiFi settings menu to connect to a wireless network.

3. Camera: Opens the camera settings menu for precise registration.

4. USB: Opens the USB menu for opening cut files from a connected USB flash drive.

5. System Info: Displays system information about the cutter.

In the ‘General Settings’ menu of your SISER JULIET SNAHDCJ12, you can make the following adjustments:

• LED: Turn the machine’s LED light ON or OFF and adjust its brightness.

• Alert: Turn the chime and/or LED light ON or OFF that indicates a completed job.

• Sleep: Set the amount of inactivity time before the cutter goes into sleep mode.

• Unit: Choose between metric (e.g., cm) and imperial (e.g., inches) measurements.

• Language: Select the desired display language for the touch screen interface.

To set up the WiFi connection on your SISER JULIET SNAHDCJ12, navigate to the ‘WiFi’ settings menu and use the following options:

1. Scan: Searches for available WiFi networks that the cutter can connect to.

2. Eye Button: Shows or hides the password as you enter it.

3. IP Address: Allows you to manually enter an IP Address for the network connection.

4. Apply: Uses the selected network or manually entered IP Address to connect.

5. Default: Switches the cutter’s WiFi to Hotspot mode, allowing you to connect directly to the machine.

The camera on the SISER JULIET SNAHDCJ12 allows for accurate tool registration for print and cut jobs. Use the ‘Camera’ menu options as follows:

1. Registration Snapshot: A crosshair overlay provides a visual preview of the tool’s orientation relative to the material.

2. Zoom: Zooms in or out on the current camera snapshot for a more detailed view.

3. Camera Snapshot: Takes a new snapshot at the tool’s current position.

4. OK: Confirms and sets the tool’s position based on the camera view.

5. Directional Arrows: Moves the machine head and material to get a different camera view of the registration marks.

6. Camera Light: Changes the brightness of the built-in camera light for better visibility.

The ‘System Information’ screen on the SISER JULIET SNAHDCJ12 displays technical details about the cutter’s firmware and hardware, such as MODE, HVER, SVER, MPID, and BAUD rate.

This screen also contains the Default All Settings button. Pressing this button will reset all cutter settings back to their original factory settings, which includes all cutting presets.

Please read and follow all safety information before using the SISER JULIET SNAHDCJ12:

• Warning: Risk of Injury, Fire, and Electric Shock. Use of the product in a manner not outlined in the operation manual may result in damage, injury, or fatal injury.

• For Indoor Use Only: The product should be used and stored in dry, indoor locations kept between 40°F and 95°F. Do not operate in or near liquids.

• Adult Operation: This product is not a toy and is intended for adult operation. It is not for use by children 12 years or under. Children must be supervised around the product.

• Condition: Do not operate the product if it is damaged or malfunctioning.

• Stable Surface: Use the product on a level and stable surface with enough space in front of and behind it for proper operation.

• Power Supply: Only use the power cord and power supply provided with the product. Do not use them if they are damaged. The cord and supply must be fully inserted into both the outlet and the cutter.

• Power Cord Safety: Position the power cord to avoid a tripping hazard. Do not place the product on the power cord.

• Disconnecting Power: Always grasp the plug, not the cord, when unplugging from an electrical outlet. Always turn the product off before unplugging.

• Surge Protector: It is recommended to plug the product into a surge protector to prevent damage from electrical malfunctions.

• Blade Handling: Use caution when handling cutting blades and do not touch the sharp edge. Store blades out of reach of children. Do not use a broken blade.

• Moving Parts: Keep objects, hair, loose jewelry, clothing, and fingers away from the product while it is operating. Do not place fingers or objects inside the product or near moving parts while it is powered on or operating.

• During Operation: Do not touch the cutting mat or materials while the product is operating until they are fully unloaded.

• Cleaning: Disconnect from power before cleaning. Clean the product with a soft, dry cloth. Do not use solvents like thinner, alcohol, or nail polish remover.

• Packaging: Keep any plastic bags used in packaging out of reach of children or dispose of them properly.

• Modifications: Do not disassemble, modify, or otherwise alter the product. Do not attempt to repair it if it malfunctions.

The SISER JULIET SNAHDCJ12 has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, you are encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.