SISER JULIET (01) PDF DOCUMENT

The main parts of the SISER JULIET cutting machine are:

1. Machine Head

2. Flip Cover

3. Touch Screen

4. Cutting Strip

5. Tool Holder: Holds the cutting blade housing or marker adapter.

6. Feed Tray: Helps stabilize material.

7. Adjustable Pinch Rollers: Feeds material in and out of the cutter.

8. Power Button

9. Pinch Roller Levers: Locks down or releases adjustable pinch rollers.

10. USB-A Port: Used for connecting flash drives to the cutter.

11. USB-B Port: Used for connecting the cutter to a computer.

12. DC Power Port

13. Roller Bar Lever: Locks down or releases material under pinch rollers.

14. Raised Feet

The SISER JULIET comes with the following accessories:

• Marker Adapter

• 45° Blade

• 60° Blade

• Blade Housing

• Power Cord and Power Supply

• USB Cord

• 12″x12″ (30x30cm) Cutting Mat

• Two sheets of 6″x12″ (15x30cm) Siser® Heat Transfer Vinyl

• One Cover Sheet

(Items are not to scale)

To set up your SISER JULIET, follow these steps:

1. Remove all protective packaging from the cutter and accessories, including plastic wrap.

2. Plug the round end of the power cord into the DC power port on the rear of the machine, then plug the opposite end into a standard electrical outlet. Press the power button to turn the cutter on.

3. Carefully remove the 45° blade from packaging and insert it into the socket on the blade housing with the pointed side facing outwards.

4. Twist the upper screw of the blade housing clockwise to expose less of the blade, or counterclockwise to expose more of the blade. The ideal length of exposed blade is about a credit card’s width. Once the blade is properly adjusted, twist the inner screw to lock in the blade position.

5. Insert the blade housing into the tool holder on the machine head with the blade facing down. Turn the knob on the tool holder clockwise to tighten.

6. Lower the roller bar lever and raise the pinch roller levers from the rear of the cutter. Adjust the pinch rollers as needed, then lower the pinch roller levers to lock them in place.

7. Lower the pinch rollers by flipping the roller bar lever up from the rear of the cutter. Push the material or cutting mat against the pinch rollers and press the ‘Up’ arrow on the touch screen to feed it into the cutter.

8. Tap ‘Cut Settings’ on the touch screen, then tap the current preset to view the entire menu. Select the preset that matches your material to automatically adjust the cut force and speed.

9. Tap ‘Test Cut’ to cut a small shape out of your material to ensure the cut settings are correct. After testing, select the ‘Home’ icon to return to the home screen.

10. Once you’re ready to cut, plug in the USB flash drive via the USB-A port on the rear of the cutter. Tap the ‘Settings’ button, then ‘USB’. Select your cut file from the drop down.

11. Move the position of the blade by using the on-screen arrow buttons. Once the blade is in position, tap the play button to begin cutting.

You can identify the quality of a test cut on your SISER JULIET as follows:

• **Bad Cut:** The cut is not deep enough and the material can’t be weeded.

• **Bad Cut:** Both the material and the carrier are cut through.

• **Good Cut:** The material is cut, but the carrier is not cut through.

The functions on the SISER JULIET Home Screen are:

1. **WiFi Indicator:** Displays WiFi connection status.

2. **Directional Arrows:** Moves material and the machine head.

3. **Play Button:** Resumes a cut or recuts the last known design.

4. **Tool Reorientation:** Moves the tool holder back to its starting position.

5. **Settings:** Opens the cutter settings menu.

6. **Cut Settings:** Opens the presets menu with adjustable cut settings.

7. **Test Cut:** Performs a test cut at the tool holder’s current position.

When a job is in progress on your SISER JULIET, the home screen shows:

1. **Pause Button:** Pauses the job at its current position.

2. **Job Progress Bar:** Displays the progress of the current job based on how far the circle is completed.

3. **Cancel Button:** Cancels the current job.

From the ‘CUT SETTINGS’ screen on your SISER JULIET, you can adjust the following:

1. **Back Button:** Returns to the previous screen.

2. **Home Button:** Returns to the Home Screen.

3. **Cutting Presets:** Opens the preset cutting menu.

4. **Cut Speed:** Adjusts how fast the machine head moves.

5. **Force:** Adjusts how much pressure the machine head exerts.

6. **Update Preset:** Overwrites a preset with the current settings.

The main settings options on the SISER JULIET are:

1. **General Settings:** Opens the general cutter settings menu.

2. **WiFi:** Opens the WiFi settings menu.

3. **Camera:** Opens the camera settings menu.

4. **USB:** Opens the USB menu for opening files from a USB flash drive.

5. **System Info:** Displays system information.

In the General Settings menu of your SISER JULIET, you can make the following adjustments:

1. **LED:** Turn the LED ON/OFF and adjust the brightness.

2. **Alert:** Turn the chime and/or LED ON/OFF that indicates a completed job.

3. **Sleep:** Set how much time of inactivity will put the cutter to sleep.

4. **Unit:** Choose between metric and imperial measurements.

5. **Language:** Select the desired language.

To set up the wireless connection for the SISER JULIET cutter:

1. **Scan:** Searches for available WiFi networks that the cutter can connect to.

2. **Eye Button:** Shows or hides the password entered.

3. **IP Address:** Manually enter an IP Address.

4. **Apply:** Uses the manually entered IP Address to connect.

5. **Default:** Switch WiFi to Hotspot mode.

Use the camera on your SISER JULIET for accurate tool registration with these functions:

1. **Registration Snapshot:** A crosshair overlay offers a visual preview of the tool orientation.

2. **Zoom:** Zooms in or out on the current snapshot.

3. **Camera Snapshot:** Takes a snapshot at the tool’s current position.

4. **OK:** Sets the tool position.

5. **Directional Arrows:** Moves the machine head and material for a different camera view.

6. **Camera Light:** Changes the brightness of the camera light.

To access and cut files from a USB drive on your SISER JULIET:

1. **File selection:** Displays folders and files on the connected USB flash drive so the desired cut file can be opened.

2. **Start cut:** Starts the job using the current settings.

The ‘Default All Settings’ button on the SISER JULIET’s System Information screen resets all cutter settings to factory settings, including cutting presets.

Please read all safety information before using the SISER JULIET. Warning: Risk of Injury, Fire, and Electric Shock. Use of the product in a manner not outlined in official material may result in damage, injury, or fatal injury.

• **For Indoor Use Only:** The product is to be used and stored in dry indoor locations only, kept between 5°C and 35°C. Do not operate the product in or near liquids.

• This product is not a toy and is intended to be operated by an adult. It is not intended for use by children 12 years or under. Children must be supervised around the product.

• Do not operate the product if it is damaged or malfunctioning.

• Use this product on a level and stable surface, allowing for enough space in front of and behind it for proper operation.

• Use only the power cord and power supply provided with this product. Do not use the power cord or power supply if damaged.

• The power cord and supply must be fully inserted into the outlet and cutter. The product should not be placed on the power cord, and the cord should be positioned to avoid a tripping hazard.

• Disconnect the product from electrical power by unplugging the power cord from the electrical outlet; always grasp the plug and never the cord.

• Always turn the product off before unplugging it from the electrical outlet.

• Disconnect the product from electrical power when not in use, before cleaning or servicing, and when replacing the cutting blade.

• To avoid injury, use caution when handling the cutting blades and do not touch the sharp edge. Cutting blades should be stored and kept out of reach of children.

• Do not use a broken blade. Remove the broken blade from the blade housing with tweezers.

• Do not load unintended materials onto the cutting mat or into the cutter.

• Keep objects, hair, loose jewelry, clothing, and fingers away from the product when it is operating, as injuries may result from the rapid movements.

• Do not touch the cutting mat or materials when the product is operating until they are unloaded from the product.

• Do not place fingers or other objects inside the product, or near any moving parts, while it is powered on, connected to electrical power, or while operating.

• Do not use solvents, such as thinner, alcohol, or nail polish remover to clean the product as it may damage the finish or touch screen. Clean the product with a soft, dry cloth.

• Any plastic bags used in packaging should be kept out of reach of children or properly disposed of.

• Do not disassemble, modify, or otherwise alter the product.

• If the product malfunctions or becomes damaged, do not attempt to repair.

The SISER JULIET has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experience radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.