PYLE PRO PPHP898A (01) PDF DOCUMENT

Before using your new Speaker System, please review the following instructions for safety and investment.

Before connecting the speaker, make sure the system is off and the controls are on the minimum level. On the contrary, the system could be damaged.

1. Plug the power cable into the AC outlet and to the system and the speaker.

2. Plug the Microphone into the “MIC” input.

3. Connect your audio source (CD, DECK, MP3, DVD, etc.) to the “LINE IN” input.

4. Turn on the systems. A green LED will light up to indicate the speaker is on.

5. Set the volume on the low level on the MIC and the LINE IN input.

6. Increase the master volume (placed on the right side of the LINE OUT connector).

7. Set TREBLE and BASS controls to equalize the sound.

8. A red LED will light up when the system detects overload power. You must decrease the volume.

Do not place the microphone against the speaker. It can cause feedback echo and it will damage the system.

The 6.3 and canon connectors marked as LINE OUT can handle an amplifier or even another powered speaker cabinet, in cascade. On the bottom of the speaker, there is a hole to place a stand.

Model: PPHP898A: 8″ 400Watts Powered 2 Way Plastic Molded Speaker Cabinet

Woofer: 8″ Woofer

Driver: 1″ Titanium Compression Driver

Inputs: XLR Mic Input, XLR & Stereo RCA Line Input

Output: XLR Line Output

Controls: Master Volume, Bass & Treble Control

Frequency Response: 45Hz-20Khz

Power Output: 200Watts RMS, 400Watts Peak

Crossover Frequency: 3.0Khz

Mounting: 35mm Speaker Stand Mount

Voltage: 110v-230 voltage

Dimensions: 13.8inch X 11.8inch X 19.3inch

1) 1/4 MIC LEVEL INPUT JACK: This jack is used for a Microphone and line level inputs. Connect a CD player or Tape Decks to LINE inputs.

2) MICROPHONE LINE LEVEL INPUT LEVEL: This knob is used to regulate the output signal of the microphone or CD player/tape deck that is connected to the Mic/Line Level jack.

3) BALANCED RCA LINE INPUT: This connection is designed to accept a balance line input signal from a mixer or other line level device with a balanced output jack. Use a balanced cable when the signal cable length exceeds 15 feet to reduce excessive signal loss. Be sure to connect only line level input devices such as mixers and tape machines to this jack.

4) BASS CONTROL: This knob is used to regulate the amount of bass applied to the output signal. The maximum amount of bass gain is +8Db and the maximum amount of bass decrease is -12db. Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.

5) TREBLE CONTROL: This knob is used to regulate the amount of treble applied to the output signal. The maximum amount of treble gain is +12db and the maximum amount of treble decrease is -12db. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal.

6) LINE LEVEL INPUT VOLUME: This knob is used to regulate the output signal if the line level source is connected to the line level input jacks.

7) XLR PARALLELED OUTPUT JACK: This jack is used to send the incoming line level signal from either of the line level input jacks to another powered speaker such as a mixer or power amp.

8) FUSE HOLDER: This housing stores the 7 amp GMA protective fuse. Always replace with the exact same type fuse, unless otherwise instructed, by an authorized service technician. Replacing with any other type of fuse than that of the recommended fuse will void your unit warranty.

9) CLIP L.E.D: When your Mic Line Level or speaker Levels are distorted or too loud, this L.E.D will light, letting you know to adjust your volume level to a lower setting.

10) POWER L.E.D: This L.E.D will be lit when you switch on the power.

11) MAIN POWER SWITCH: This is the main power ON/OFF button. A yellow LED directly above the power switch will glow, indicating power is ON. Before main power is applied, be sure you have made all connections to the speaker. Remember to avoid damaging pops to the speakers; the mixer is turned on first and turned off last.

12) MAIN POWER INLET: This connector is used to supply main power to the unit via the included detachable power cord. The power connection uses an I.E.C. type connector. Use only the supplied polarized AC power cord that matches this type of connection. Be sure to only connect this unit to a power outlet that matches the printed power label on the unit. Never use a power cord when the ground prong has been removed or broken off. The ground prong is used to reduce the risk of electrical shock in case of an electrical short. This cord is designed to fit in one direction only. Do not attempt to force a cord if it does not fit; be sure the cord is being inserted properly.

COMPONENT	PPHP898A SPECIFICATION
WOOFER
Impedance	4OHM
Sencitivity	95DB
Frequency	45-20k Hz
Diameter	8INCH
Coil Diameter	1.5INCH
Magnet	30OZ
TWEETER
Impendance	8OHM
Sencitivity	101DB
Frequency	800Hz-20kHz
Coil Diameter	1INCH
Diaphragm	Titanium
Magnet	NEODYMIUM
Build-in Amp	YES
Power(MAX)	400W
Dimension	13.8inchX11.8inchX19.3inch